Alissa Charlotte Wiengarten - mpq.mpg.de · and study the intermolecular interactions. The concept...
Transcript of Alissa Charlotte Wiengarten - mpq.mpg.de · and study the intermolecular interactions. The concept...
Technische Universitat Munchen
Physik Department E20
Molecular Nanoscience and Chemical Physics of Interfaces
Scanning tunneling microscopy investigation
of structure and electronic properties of
surface-confined tetrapyrrolic species
Dissertation
Alissa Charlotte Wiengarten
Technische Universitat Munchen
Lehrstuhl E20 - Molekulare Nanowissenschaften und Chemische Physikvon Grenzflachen
Scanning tunneling microscopy investigation
of structure and electronic properties of
surface-confined tetrapyrrolic species
Alissa Charlotte Wiengarten
Vollstandiger Abdruck der von der Fakultat fur Physik der Technischen Universitat Munchen
zur Erlangung des akademischen Grades eines Doktors der Naturwissenschaften genehmigten
Dissertation.
Vorsitzender: Univ.-Prof. Dr. J. Leo van Hemmen
Prufer der Dissertation: 1. Univ.-Prof. Dr. Johannes V. Barth
2. Univ.-Prof. Dr. Joost Wintterlin,
Ludwig-Maximilians-Universitat Munchen
Die Dissertation wurde am 24.06.2015 bei der Technischen Universitat Munchen
eingereicht und durch die Fakultat fur Physik am 21.07.2015 angenommen.
I
Abstract
On-surface chemical reactions and the adsorption behavior of functional molecules on metal
surfaces are studied; aiming for the formation of covalent nanostructures and derivatives of
molecules with enhanced properties. For a future application in devices and the creation of new
two-dimensional materials it is required to understand the processes on surfaces on the molec-
ular level. In this work, the structural and electronic properties of tetrapyrrolic molecules are
investigated in a well-defined environment, namely on single crystal surfaces in an ultra-high
vacuum chamber, by means of scanning tunneling microscopy and complementary methods.
Catalyzed by a silver substrate, covalent oligomeric nanostructures are formed on the surface
for different porphyrin molecules. The coupling leads to a decrease of the electronic band gap
and the properties of the structures can further be tuned by the incorporation of a metal ion in
the tetrapyrrolic macrocycle. Intramolecular ring-closing reactions are observed, with different
product distributions for metalated and metal-free porphyrins.
The adsorption-induced change of the symmetry and electronic structure of a molecule is de-
scribed for iron-phthalocyanine on a copper surface. Furthermore, for two metallo-porphyrins
adsorbed on a silver surface the binding affinity towards small gas molecules is studied, moti-
vated by the functionality of heme in oxygen transport.
Finally, the intermolecular interactions in a model system for a bimolecular organic solar cell
are investigated.
II
CONTENTS III
Contents
Abstract I
1 Introduction 1
2 Experimental Methods 5
2.1 Scanning Tunneling Microscopy . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1.1 Theory of Scanning Tunneling Microscopy . . . . . . . . . . . . . . . . . . 5
2.1.2 Scanning Tunneling Spectroscopy . . . . . . . . . . . . . . . . . . . . . . . 9
2.1.3 Modes of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.1.4 Instrumentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.1.5 Sample preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.2 Complementary methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.2.1 Near edge X-ray absorption fine structure spectroscopy . . . . . . . . . . 20
2.2.2 Photoelectron spectroscopy . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.2.3 Temperature-programmed desorption . . . . . . . . . . . . . . . . . . . . 23
2.2.4 Computational details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3 Covalent coupling of porphines 25
3.1 Free-base porphine on Ag(111) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.1.1 Homocoupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.1.2 Electronic structure and physical properties . . . . . . . . . . . . . . . . . 32
3.2 Free-base porphine on Ag(100) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.3 Co-porphine on Ag(111) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.3.1 Covalent coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
3.3.2 In-situ metalation of oligomers . . . . . . . . . . . . . . . . . . . . . . . . 41
3.4 Dibromoporphines on Ag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3.5 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
4 Ring-closing reactions on phenyl-substituted porphyrins 55
4.1 Tetraphenylporphyrins on Ag(111) . . . . . . . . . . . . . . . . . . . . . . . . . . 55
4.2 5,15-Diphenylporphyrins on Ag and Cu surfaces . . . . . . . . . . . . . . . . . . . 60
4.2.1 Ring-closing reactions on Ag and Cu . . . . . . . . . . . . . . . . . . . . . 61
4.2.2 Covalent coupling on Ag and Cu . . . . . . . . . . . . . . . . . . . . . . . 64
4.2.3 Electronic structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
4.3 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
5 Adsorption and coupling of iron-phthalocyanine on Cu(111) 71
5.1 Symmetry reduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
5.2 Polymerization reactions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
5.3 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
6 Interaction of metalloporphyrins with diatomic gas molecules 77
6.1 Metalation of 2H-TPP with Iron . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
6.1.1 Metalation on the Ag(111) surface . . . . . . . . . . . . . . . . . . . . . . 78
6.1.2 Metalation on a boron nitride layer . . . . . . . . . . . . . . . . . . . . . . 79
6.2 Interaction of Fe-TPP on Ag(111) with CO and O2 . . . . . . . . . . . . . . . . . 82
6.3 Interaction of Ti-TPP on Ag(111) with O2 . . . . . . . . . . . . . . . . . . . . . . 86
6.3.1 Metalation of 2H-TPP with Titanium . . . . . . . . . . . . . . . . . . . . 87
6.3.2 Oxidation of Ti-porphyrins . . . . . . . . . . . . . . . . . . . . . . . . . . 89
6.4 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
7 Intermolecular interactions at the model interface of an organic solar cell 95
7.1 BO-ADPM on Ag(111) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
7.2 Interaction of BO-ADPM and C60 . . . . . . . . . . . . . . . . . . . . . . . . . . 97
7.3 Measurement of the electronic band gap . . . . . . . . . . . . . . . . . . . . . . . 99
7.4 Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
8 Conclusion and perspectives 101
List of publications 105
References 107
Acknowledgment 125
1
1 Introduction
One of the first laboratory experiments was the inclined plane built by Galileo Galilei. He
paved the way for the subsequent history of laboratory systems that in some way reduced a phe-
nomenon to its basic traits or reproduced it in a controlled manner with the goal to understand
its fundamental principles. This concept is of invaluable importance for science, as research had
been limited to descriptive observations of phenomena before. By far shorter is the history of
surface science employing metal, semiconductor and insulator surfaces as its laboratory systems
and aiming to understand the processes that take place at interfaces.
Although some pioneering studies focus on several effects related to surfaces and interfaces such
as the work of Irving Langmuir on adsorption chemistry and kinetics, [1] the discovery of the
photo effect [2] and of electron diffraction, [3] only in the 1960ies surface science became a field
of research on its own. This breakthrough was triggered by mainly three inventions, namely
electron spectroscopy as a surface-sensitive tool, vacuum chambers enabling to retain clean sur-
faces and slightly later computers that allow complex modeling. [4] Only 20 years later the
invention of the scanning tunneling microscope (STM) allowed to atomically resolve conducting
surfaces and structures on surfaces. [5] This ability was extended to insulating surfaces with the
invention of the atomic force microscope. [6]
Surface science deals with the characterization of solid-vacuum and solid-liquid interfaces, where
the topmost 10 A of a bulk material are regarded as the surface region. Processes on surfaces
are investigated, such as adsorption, desorption, diffusion and self-organization. Furthermore,
the electronic structure of surfaces is explored as well as the growth and properties of thin films.
Surface science also contributes to the field of heterogeneous catalysis with studies on surface
reactions and the catalytic activity of adsorbates. [7, 8] The most prominent application is the
fabrication of semiconductor devices where it is important to understand the interfacial pro-
cesses. As foreseen by Richard Feynman, [9] the structure size in electronic and optoelectronic
devices is still shrinking which requires an understanding of the components on the atomic level.
Porphyrin molecules came into the focus of surface science studies because of their relevance in
many biological systems and their versatile tunable properties. [10] The macrocycle consisting
of four pyrrole rings which are connected by methine groups is very stable and can host differ-
ent metal ions. As part of hemoglobin, porphyrins with an iron center are responsible for the
oxygen transport in blood. [11] Magnesium porphyrins on the other hand play an important
role in the photosynthesis in plants. [12] These and other characteristic features of porphyrins
enabled a variety of applications. Due to their ability to coordinate small gas molecules por-
phyrins are employed as gas sensors, [13–15] whereas their optical properties are explored for
artificial photosynthesis, [16] organic solar cells, [17] light emitting diodes [18] and photosensi-
tizers in photodynamic therapy. [19] Moreover, porphyrins are employed as catalysts. [20, 21]
Their properties can further be tuned by adding different substituents at the macrocycle and
2 1 INTRODUCTION
upon adsorption on metal surfaces the substrate often acts as an additional ligand. [10]
Recently, porphyrins became part of extensive research on molecular systems suitable for the
employment in molecular electronics [22] and optoelectronics. In order to overcome the limi-
tations in structural size for semiconductor materials functional properties of single molecules
are explored, such as switching or rectifying. [22,23] For the application in a device these func-
tional units need to be connected to allow an efficient charge transport. [24] For this reason,
covalent coupling reactions between a variety of molecules on metal surfaces have been investi-
gated. [25,26] Furthermore, the goal is to create new two-dimensional materials. [27, 28]
In this work, functional molecules as porphyrins are studied in a well-defined environment, i.e.
the laboratory system is an ultra-high vacuum chamber where the sample is cooled in order
to reduce thermal motion and increase spectral resolution. A scanning tunneling microscope
enables to characterize the geometric structure of the molecules, probe their electronic states
and study the intermolecular interactions.
The concept of this approach is to understand the basic properties of a system before designing
a device or application. The adsorption of a molecule on a metal surface can drastically change
its properties due to the strong interaction with the substrate. Its geometry can be distorted in
comparison to the gas phase conformation, [29, 30] the electronic states are shifted and broad-
ened because of the interaction with the metal [31] or the magnetic properties of a molecule can
be influenced by the substrate. [32,33] It was also shown that the catalytic activity of adsorbed
molecules depends on their adsorption site [34] as well as their affinity to bind ligands is influ-
enced by the substrate. [35, 36]
This work shows that the interaction with the underlying metal can have a substantial impact
on the functionality of adsorbed molecules and needs to be investigated in a well-defined envi-
ronment in order to understand and tune the properties of a future device.
In the following chapters different molecular systems are discussed and characterized mainly by
STM and several complementary techniques. The mode of operation and theory of STM are
elucidated in chapter 2 (ch.). Furthermore, the instrumentation of the ultra-high vacuum system
is explained as well as the sample preparations. The chapter finishes with the short introduction
of the complementary methods.
In the third chapter, on-surface chemical reactions involving different porphine molecules are
investigated. Porphines are the macrocycle of each porphyrin molecule and they can host a
metal ion in their center. Heat-induced and surface-assisted covalent coupling reactions are
observed for non-metalated porphines on Ag surfaces and for Co-porphines as well, leading to
the formation of covalently coupled oligomers. With the introduction of bromine atoms at the
periphery of the molecules a more directed growth of the nanostructures is aimed for.
Chapter 4 deals with intramolecular ring-closing reactions on tetraphenylporphyrins on a Ag(111)
surface. Enhancing the symmetry of the core of the molecule by the incorporation of a metal
3
ion in the center changes the reaction outcome. A very similar molecule, the diphenylporphyrin,
undergoes the same ring-closing reactions and couples covalently at elevated temperatures.
In the following chapter, the surface-induced symmetry reduction apparent in STM images of a
molecule similar to porphyins, namely Fe-phthalocyanine, is discussed. Moreover, polymeriza-
tion reactions on the Cu(111) surface are observed.
Chapter 6 addresses the reactivity of surface-anchored metallo-porphyrins towards small ligands.
The interaction with the metal substrate strongly influences the binding affinity of the metal
centers and their catalytic activity.
At last, a model system for a bimolecular organic solar cell is investigated. The interaction of
the two compounds is studied on the Ag(111) surface and the electronic band gap is measured.
The results are summarized in the conclusion.
4 1 INTRODUCTION
5
2 Experimental Methods
The main experimental technique employed in this work is scanning tunneling microscopy
(STM). Its theory, the working principle and the experimental details are elucidated in the
following. Furthermore, several other techniques were applied by coworkers in joint efforts to
substantiate some of the findings obtained during the STM measurements. A brief overview
about these complementary methods is given in the last part of this chapter.
2.1 Scanning Tunneling Microscopy
The current arising from electrons tunneling between a sharp metal tip and a conducting
surface due to an applied bias depends exponentially on the vacuum gap width between tip and
surface. This relation was first measured by Binnig and Rohrer in 1982 [37] and let to their
invention of the scanning tunneling microscope (STM). [5] The STM enables to acquire images of
conducting surfaces, structures on these surfaces and adsorbates with atomic resolution. [5, 38]
Since the tunneling current depends exponentially on the distance between tip and surface,
the topography of a surface can be measured by scanning the surface with the tip in a two-
dimensional pattern. Either the tunneling current or the vacuum gap width are kept constant
and the variation in the respective other parameter gives the surface topography.
In 1986, Binnig and Rohrer were awarded the Nobel Prize for their invention. [39] Since then,
a very wide field of research based on the STM evolved, e.g. the characterization of metal and
semiconductor surfaces, [38] of adsorbates on surfaces, [40] of molecular orbitals [41] and spin-
polarized STM. [42]
In the following, the theory of STM, the different modes of operation and the instrumentation
are summarized.
2.1.1 Theory of Scanning Tunneling Microscopy
The first theoretical description of electron tunneling between two solids was given by
Bardeen in 1961. [43] He calculated the tunneling current by evaluating the time-dependent
many-particle wave function of the whole system. After the first STM was put into operation
Tersoff and Hamann employed Bardeen’s method to calculate the tunneling current of an STM
and the local density of states (LDOS) of several surfaces. [44,45] Although their theory is only
correct for tip-surface distances of several A and tips exhibiting s-wave character, it explains the
imaging of surface reconstructions, scattered waves of surface states and defects. The following
description gives a summary of this first approach by Tersoff and Hamann. However, several
different theories were developed up to now, which account for a wide range of experimental
observations (for an overview see [46,47]).
6 2 EXPERIMENTAL METHODS
Figure 2.1: One-dimensional tunneling junction: Shape of the wave function of electrons tunneling through thevacuum gap between two metals.
The imaging in STM relies on electrons overcoming a certain potential barrier U , namely the
work function of the respective material. In classical mechanics electrons cannot overcome a po-
tential barrier that is higher than their own energy E, thus it cannot explain the phenomenon of
tunneling. However, in quantum mechanics electrons are described by wave functions ψ obeying
the Schrodinger equation
− ~2
2m
d2
dz2ψ(z) + U(z)ψ(z) = Eψ(z)
where m is the electron mass and the direction of z is shown in figure 2.1 (fig.). This equation has
solutions for U < E as well as for the case of U > E, i.e. if the potential barrier is higher than
the energy of the electrons they can still penetrate into the barrier with a certain probability
which exponentially decays with z [47] (see fig. 2.1).
Bardeen [43] described the tunneling of electrons between two electrodes A and B, separated
by a vacuum barrier, by solving the Schrodinger equation of the combined system:
i~∂ψ
∂t=
(− ~2
2m
∂2
∂z2+ UA + UB
)ψ
where ψ is the wave function of the whole system and UA and UB are the potential functions of
the two electrodes (see fig. 2.2).
Since there is a certain probability for electrons tunneling from electrode A to B, the wave
function of the whole system ψ is calculated by first order perturbation theory:
ψ = ψµe− iEµt~ +
∞∑ν=1
cν(t)ψνe− iEνt~
where ψµ is the wave function of electrode A with eigenvalues Eµ and ψν is the wave function
of electrode B with eigenvalues Eν , t is the time and cν(t) are the coefficients that need to be
2.1 Scanning Tunneling Microscopy 7
Figure 2.2: One-dimensional tunneling junction: Wave functions of tip and sample.
determined from the Schrodinger equation of the whole system and which give the tunneling
probability.
Based on Bardeen’s theory, Tersoff and Hamann [44, 45] gave an expression for the tunneling
current between the two electrodes A (tip) and B (surface):
I =2πe
~∑µ,ν
f(Eµ)(1− f(Eν + eV ))|Mµν |2δ(Eµ − Eν). (2.1)
The function f(E) is the Fermi function, V is the applied bias and |Mµν |2 is the tunneling matrix
element derived by Bardeen and it is proportional to the tunneling probability. The δ-function
in the end of equation 2.1 (eq.) accounts for the condition of elastic tunneling, i.e. electrons can
only tunnel into states of the same energy.
As a first approximation, it is assumed that the applied biases are small and that the temperature
is small, such that the Fermi function becomes a step function. It follows that
I =2π
~e2V
∑µ,ν
|Mµν |2δ(Eν − EF )δ(Eµ − EF ) (2.2)
where EF is the Fermi energy.
The equation for the tunneling current can be further simplified by assuming that the tip is
point like. Consequently, I is independent of the wave function of the tip ψµ:
I ∝∑ν
|ψν(~r0)|2δ(Eν − EF ) = ρs(~r0, EF ). (2.3)
Thus, if the tip is assumed to be featureless, the tunneling current is proportional to the local
density of states ρs(~r0, EF ) of the surface at ~r0 and at the energy EF . This finding will be
compared to a more detailed calculation of I in the following.
In order to calculate I from eq. 2.2, Tersoff and Hamann calculated the tunneling matrix element
8 2 EXPERIMENTAL METHODS
which was given by Bardeen:
Mµν =~2
2m
∫d~S (ψ∗µ
~∇ψν − ψ∗ν ~∇ψµ). (2.4)
The integral is evaluated on a surface S which has to lie in the vacuum gap between tip and
surface.
Mµν is calculated by firstly giving an expression for ψν by expanding it and secondly assuming
that the tip is spherical at the apex and thus exhibits s-wave character which gives an expression
for ψµ. Therefore, this assumption is only valid for small tip radii, on the other hand, for broader
tips a more detailed description about the local conformation would be required.
Inserting the expressions for the two wave functions into eq. 2.4 and thus into eq. 2.2 gives an
experimentally accessible expression of the tunneling current:
I =32π3
~e2V φ2Dt(EF )
R2
κ4e2κR ×
∑ν
|ψν(~r0)|2δ(Eν − EF ) (2.5)
where φ is the work function of the tip, Dt is the density of states (DOS) per unit volume of the
tip, R is the tip radius and κ =√2mφ~ is the minimum inverse decay length of the wave functions
in vacuum.
If values typical for many metals are inserted, the conductance σ amounts to:
σ =I
V= 0.1R2e2κRρs(~r0, EF ) (2.6)
with ρs being the LDOS of the surface:
ρs(~r0, EF ) =∑ν
|ψν(~r0)|2δ(Eν − EF ).
As |ψν(~r0)|2 ∝ e−2κ(R+d) was derived during the expansion of ψν , it follows that
σ ∝ e−2κd
where d is the distance between tip and surface. The same exponential dependence was measured
by Binning and Rohrer in their first STM experiments. [37] Furthermore, eq. 2.6 gives the same
proportionality as eq. 2.3, i.e. the proportionality of the tunneling current is the same if the tip is
assumed to be point-like. Thus, in this model the properties of the tip are assumed to be known
(namely point-like or s-wave character) and with this the tunneling current only depends on the
electronic structure of the surface and the tip-surface distance. If the tunneling current is held
constant, a convolution of the electronic states of the surface and its topography is recorded.
However, in order to understand the imaging of structures, it is necessary to take into account
the electronic states of the tip as well since the conductance measured in STM is a convolution
2.1 Scanning Tunneling Microscopy 9
of the electronic states of the sample and the tip. [47]
Figure 2.3: Tunneling junction with positive bias applied to the sample: Electrons tunnel from occupied statesof the tip into unoccupied states of the surface.
Figure 2.3 shows schematically how the tunneling process is influenced by the DOS of both tip
and sample. If a bias eV is applied to the sample the two Fermi levels are not aligned anymore
but shifted towards each other by eV . In the case of positive bias in fig. 2.3 electrons can tunnel
from occupied states of the tip into unoccupied states of the surface. The electrons close to the
Fermi energy contribute most to the tunneling current which is marked by the thicker red arrow
since they have the highest energy. If the polarity of the applied bias is inverted the electrons
tunnel from occupied states of the sample into unoccupied states of the tip.
2.1.2 Scanning Tunneling Spectroscopy
Since the tunneling current in STM depends on the density of electronic states of the surface,
the STM enables to investigate not only the topography of a surface but also its electronic
structure. Whereas in the normal scanning mode, all electronic states up to eV contribute
to the tunneling current, in scanning tunneling spectroscopy (STS) only a small energy range
is chosen to contribute to the tunneling process. STS was first proposed by Selloni et al. in
1985 [48] and they computed how the derivative of the tunneling current I is related to the
electronic states of the surface using a simplified tunneling model. The first tunneling spectra
were recorded by Binnig et al. on the Ni(100) surface. [49] In general, STS can be employed
to study surface states and resonances, [50,51] catalytically active sites on the surface [52] and
energy levels of adsorbed molecules. [41]
Based on the calculations summarized above the change in I in dependence of the applied bias
V can be calculated by using the Wentzel-Kramers-Brillouin (WKB) approximation. [53] In the
previous chapter I was calculated under the assumption that the applied bias is small. However,
in STS measurements larger biases are applied to the tunneling junction. Thus, all electronic
10 2 EXPERIMENTAL METHODS
states up to an energy of eV contribute to I in the WKB-approximation:
I ∝∫ eV
0ρs(E)ρt(E)T (E, eV )dE (2.7)
where ρt is the DOS of the tip which is assumed to be constant since clean metallic tips often
exhibit this feature. T is the transmission probability and it accounts for the exponential
dependence of I on the tip-surface distance:
T (E, eV ) = e−2κd.
Differentiating eq. 2.7 with respect to V gives [53,54]:
dI
dV∝ eρs(eV )T (eV, eV ) + e
∫ eV
0ρs(E)
d
d(eV )(T (E, eV ))dE. (2.8)
The integral describes the V -dependence of T (E, eV ) which is a monotonically increasing func-
tion in the WKB-approximation. Therefore, the integral in eq. 2.8 gives a continuous background
in the dI /dV signal which is proportional to the DOS of the surface at the applied bias. Conse-
quently, by measuring the derivative of I the electronic states of the surface can be probed with
submolecular resolution. The ability to position the tip precisely over certain features and to
probe the electronic states on a very small lateral scale has great advantages in comparison to
space-averaging techniques such as photoemission spectroscopy. [53] Moreover, with STS both
occupied and unoccupied states can be probed.
Experimentally, STS can be realized in two different ways. The first method is to keep the
tip-surface distance constant while the applied bias is continuously altered in a certain range.
The recorded tunneling current is differentiated with respect to the bias. [54] As shown above,
the derivative is proportional to the DOS of the surface.
The second method makes use of a small modulation voltage which is superimposed with the
applied dc bias Vdc between tip and surface. The modulation voltage exhibits sinusoidal shape
and its frequency ω has to be larger than the feedback loop cut-off. Thus, I is modulated by ω
but the feedback loop does not correct the tip-surface distance and the ac signal of I gives the
derivative. The component of I which is in phase with ω, measured with a lock-in amplifier,
directly gives the dI /dV signal at Vdc. [49, 53,55]
Spectroscopy can be either performed at one particular site on the surface or an ST spectrum
can be acquired at each point of the image. If the modulation bias technique is used to record
the dI /dV signal at a certain Vdc over a small two-dimensional area, it will be referred to as
dI /dV mapping in the following.
2.1 Scanning Tunneling Microscopy 11
2.1.3 Modes of operation
The two most employed modes of operation in order to acquire topography images are
described in the following. More specialized modes are described elsewhere. [56]
Constant current mode
In the constant current mode the height of the tip over the surface is adjusted in such a way that
the tunneling current is constant during the x-y scan over the surface. A feedback loop applies
a voltage to the piezo which controls the z-movement of the tip and thus alters the height of the
tip in order to keep the tunneling current constant. From the voltage applied to the z-piezo the
topography at each point of the surface can be determined. For this operation mode the surface
does not have to be atomically flat, i.e. steps and adsorbates can easily be imaged. However,
the scanning speed is limited by the response time of the feedback loop. [5, 56]
Constant height mode
The constant height mode enables faster scanning speeds since the feedback loop is open in
order to keep the height of the tip over the surface constant during the x-y scan. [57] The
topography of the surface is derived from the change in the tunneling current at each point.
The disadvantage of this mode is that the surface has to be very flat so that the tip does not
crash into the surface during scanning. Furthermore, to avoid drift a high stability is required.
2.1.4 Instrumentation
The STM utilized in this work was developed by G. Meyer, S. Zophel and K. Schaeffer at
the Freie Universitat Berlin [58, 59] and is commercially available from CreaTec Fischer & Co.
GmbH. [60] It is installed in an ultra-high vacuum (UHV) chamber and usually operated at 6 K.
In the following, the UHV chamber with its different components and the STM scanner itself
are described. Subsequently, the sample preparation is addressed.
UHV chamber
In order to investigate surfaces via STM a very clean environment, e.g. UHV, is required. At
ambient pressures, small molecules such as water, oxygen and carbon monoxide easily cover
metal surfaces or even react with them. If the pressure is decreased the number of particles per
unit volume decreases and the mean free path of the particles increases. As a rough estimation,
it is assumed that the surface is investigated over a time span of 104 s and that the desired
maximal coverage with adsorbates during this time is 1100 of a monolayer. It follows that the
pressure has to be 5 · 10−12 mbar. These low pressures are very hard to achieve and since most
of the remaining gas molecules do not change the surface structure pressures in the range of
10−10 mbar are sufficient for the majority of the experiments. [61]
12 2 EXPERIMENTAL METHODS
Figure 2.4: UHV chamber: STM chamber with cryostat on the left and preparation chamber on the right. Atthe bottom of the chamber the turbo and ion getter pumps are mounted. The whole frame is placed on fourpneumatic legs. Adapted from [62].
The UHV system used for this work consists of two chambers, namely the preparation chamber
and the STM chamber with a cryostat on top (see fig. 2.4). The chambers are connected via
a gate valve. The UHV condition is achieved by several pumps. A dry diaphragm pump ac-
complishes a pressure of 1 mbar in the first stage of the pumping system so that the first turbo
molecular pump (from Alcatel [63]) can be operated. It is followed by the main turbo pump
(from Leybold [64]) which is directly connected to the preparation chamber. Turbo molecular
pumps are able to maintain UHV conditions by rotating tilted blades mounted to the rotor
and inducing a flow of the remaining particles out of the chamber. [61] Furthermore, in each
chamber one ion getter pump further decreases the pressure by ionizing the residual gases with
field-emitted electrons and accelerating them onto a titanium (Ti) electrode where they react
with the Ti and stick to a getter plate. Another method to decrease the pressure is the evapo-
ration of cerium (Ce). If the walls of the chamber are covered with Ce, remaining particles can
react with the Ce and are trapped at the walls. At last, the Ti sublimation pump decreases
the pressure for several hours when Ti is deposited onto a getter plate which is cooled by liquid
nitrogen. With the combination of these pumps the usual base pressure is 5 · 10−10 mbar. The
pressure in both chambers is monitored by cold cathode gauges from Pfeiffer. [63] They ionize
gas molecules and the resulting ion current is a measure for the amount of gas molecules in the
chamber and thus for the pressure. [8]
The preparation chamber is equipped with several tools for sample preparation and cleaning. A
2.1 Scanning Tunneling Microscopy 13
sputter gun ionizes Ar atoms which can be dosed into the chamber via a leak valve. After clean-
ing the sample, the crystallinity can be examined via low energy electron diffraction (LEED).
With a quadrupole mass spectrometer (from Scientific Instruments [65]) the composition of the
residual gases in the chamber or the purity of other gases dosed via leak valves can be deter-
mined.
The molecules required for most of the experiments are evaporated onto the sample via organic
molecular beam epitaxy (OMBE), i.e. the molecules are evaporated from a quartz crucible which
is heated resistively. In order to increase the molecular flux the temperature of the crucible is
increased. Furthermore, different metals can be deposited onto the surface. Cobalt (Co) and
iron (Fe) can be evaporated from a wire which is coiled around a tungsten (W) filament that is
heated resistively. Moreover, Fe was also evaporated by electron bombardment from an electron
beam evaporator with the following parameters: Ifilament = 1.66 A, Iemission = 13 mA, Flux =
2.0 nA, U = 675 V, td = 2 min.
Additionally, up to five sample holders can be stored inside the preparation chamber or a load-
lock can be employed so that different crystals can be studied without breaking the vacuum.
The sample holder is positioned on the manipulator which can be moved from the preparation
chamber into the STM chamber and it can be cooled with liquid helium, either during sample
preparation or in order to pre-cool the sample for the STM measurements. In the STM chamber
the STM scanner is mounted in direct contact to a cryostat which is cooled with liquid helium.
The outer part of the cryostat is filled with liquid nitrogen as a first cooling shield. The inner
part is filled with liquid helium and both parts are equipped with aluminum (Al) radiation
shields. The STM is located inside a radiation shield which is directly attached to the inner part
of the cryostat and thus the whole STM scanner can be stabilized at an equilibrium temperature
of 6 K. Since the pressure gauge in the STM chamber is outside of the radiation shield where
the temperature is higher, it is assumed that the pressure inside the shield is even lower than
measured by the gauge.
The whole system with both chambers is connected via a frame which is positioned on four
pneumatic legs. When inflated with air, they damp low frequency vibrations from the building
and the ground.
STM scanner
The configuration of the STM scanner is shown in fig. 2.5a. The purpose of this beetle-type
design was rigidity and simplicity. [66] The sample is positioned on the base plate on which
three piezo electric tubes are glued. The piezo electric effect enables a very precise control
of the tip movement. If a voltage is applied to a piezo electric material it is deformed in a
certain direction. [47] Since the length scale of the deformation amounts to several A/V at
low temperatures movements with subatomic resolution can be induced in a controlled way.
The three piezo electric tubes are each contacted with four metal electrodes from the outside
14 2 EXPERIMENTAL METHODS
(for triggering the x-y movement) and one from the inside (for triggering the z-movement, see
fig. 2.5b). On top of each tube a sapphire sphere is mounted. The tip is positioned above the
sample and it is fixed to a ramp that lies on the three sapphire spheres. The coarse movement
of the tip is realized by the three piezo tubes. For this purpose the ramp is divided into three
equal parts each of which is slightly inclined. If the same voltage is applied to the three piezos
and if the deformation is slow and uniform the ramp follows the movement of the piezos. A
net displacement of the ramp is achieved by a slow deformation of the piezos followed by a fast
deformation in another direction. The ramp cannot follow the faster movement because of its
inertia and if both steps are repeated after each other the ramp is displaced relatively to the
piezos. Since the three segments of the ramp are inclined a movement in z-direction is realized
as well. The tip is mounted on the inner piezo in the center of the ramp which is responsible
for the fine movement of the tip. [59]
Figure 2.5: a) STM scanner with tip attached to ramp and outer piezos on base plate. The coarse movementof the ramp is triggered by the outer piezos and the fine movement during scanning by the inner piezo. b) Outerpiezo with electrical contacts. By applying voltages the piezo tube can be deformed in all three directions ofspace. Taken from [59].
The base plate with the STM scanner is hanging at three long soft springs that are attached to
the cryostat (see fig. 2.6). During cooling the base plate is pressed against a plate which is in
direct contact with the inner cryostat. The STM scanner can be released to hang freely at the
three springs via a pulling mechanism which can be operated from outside. In order to minimize
vibrations the scanner is released during measurements. Vibrations of buildings are in the range
from 1 to 100 Hz. Both the pneumatic legs and the springs damp these low frequency vibrations.
Another method to further decrease the coupling of the STM with low frequency vibrations is
to keep the resonance frequency of the whole STM scanner as high as possible by designing it
to be rigid. [47] Additionally, three magnets placed below the base plate act as eddy current
dampers.
The tips used in this work are chemically etched W tips. They are fabricated by mounting a
W wire (diameter: 0.25 mm) in such a way that it hangs in the center of a loop of a gold wire
(see fig. 2.7). In the loop a thin film of NaOH solution (2 mol/L) is created by dipping it into a
2.1 Scanning Tunneling Microscopy 15
Figure 2.6: Picture of the STM scanner without cooling shield and without sample. The tip is in the centerabove the block for the sample holder with six metal contacts. Two outer piezos are visible on the base plate andthe three long springs that are attached to the cryostat. Picture taken by Knud Seufert.
solution. The W wire is hold from the top and the part below the loop should be longer than the
length required for the tip. An electro-chemical cell is realized by applying a voltage between
the W wire and the wire of the loop (3 to 4.5 V). Thus, the part of the W wire in the solution
is etched and W-oxide is created. The following chemical reaction takes place:
W (s) + 2OH− + 2H2O →WO2−4 + 3H2(g)
The part of the W wire in solution becomes thinner during the etching process until the waist
is thin enough so that it cannot hold the weight of the bottom part anymore and it falls. The
bottom part should be caught so that it can be used as a tip. Since the etching slowly removes
the material and in the end there is a very high strain at the waist, this technique usually yields
very sharp tips. [47] After etching the tip needs to be cleaned immediately with distilled water
to remove the solvents and by sputtering the W-oxide is removed. Both parts of the W wire can
be used as a tip. The W wire is slightly bent in a zig-zag fashion in order to hold it rigidly in
the tip holder.
In the vacuum chamber the tip is cleaned by argon (Ar) ion sputtering. During the STM mea-
surements the tip needs to be frequently treated as well since it often changes the structure at
the apex by interaction with the substrate or residual gases. For this purpose a bias higher than
usually used during measurements, i.e. up to 10 V is applied between tip and sample or the
current is increased in order to strengthen the tip-surface interaction. Thus, the tip can pick up
material from the surface or drop adsorbates from the apex of the tip. Another procedure is to
bring the tip into physical contact with the surface. If the surface below the tip is clean metal
the tip can be covered with that metal which is desired in many cases (see e.g. ch. 2.1.2). It is
16 2 EXPERIMENTAL METHODS
Figure 2.7: Etching of a W tip in a film of NaOH solution. The gold wire is the counter electrode of theelectro-chemical cell.
also possible to apply a combination of both methods. However, the structure at the apex of
the tip cannot be changed in a controlled way and is mostly unknown. [53] A commonly used
method to test if the tip is metallic at the apex is to record a tunneling spectrum on a bare metal
surface. Silver (Ag) and copper (Cu) surfaces exhibit characteristic surface states. [67,68] If no
other peaks are observed in the dI /dV curve the tip is assumed to be suited for spectroscopy.
The scanning of the tip over the surface is controlled by a digital signal processor (DSP) (see
fig. 2.8). The tunneling current I is amplified and converted into a voltage and this voltage
is converted into a digital signal. The feedback loop compares the voltage resulting from the
tunneling current to the preset value for the tunneling current and applies a voltage to the
piezos in order to adjust the tip-sample distance such that the tunneling current stays constant.
The voltage signal for the piezos is amplified to achieve the desired movement. Furthermore,
the DSP controls the bias between tip and sample. The STMAFM 2.0 software [60] enables to
adjust all parameters for scanning and for dI /dV measurements which are acquired by using
an internal lock-in amplifier with Vrms = 18 mV and f = 2.97 kHz.
2.1.5 Sample preparation
Single crystal cleaning
The different metal crystals were cleaned in UHV environment by several cycles of Ar ion sput-
tering and annealing. The Ar+ ions are generated by backfilling the chamber with Ar gas
( 2.5 ·10−5 mbar) through a leak valve and ionizing the gas particles with an ion gun by electron
impact ionization. The applied voltage of the sputter gun is usually 800 V. The charged particles
are accelerated towards the crystal and collide with the surface where they remove material from
the surface. Consequently, other adsorbates on the surface are either sputtered away or they can
be buried deeper below the surface. [61] During sputtering the current given by the Ar+ ions is
measured to be around 4.5µA. Subsequently, the crystal is annealed at 720 K. During annealing
2.1 Scanning Tunneling Microscopy 17
Figure 2.8: Schematic of the electronics controlling the STM measurements. All signals are processed digitallyand regulated via the software STMAFM 2.0. Taken from [60].
impurities from deeper layers of the crystal as well as remaining Ar ions are brought to the
surface and desorb. Repeated cycles of sputtering and annealing yield clean crystal surfaces.
Crystal surfaces
The single crystals employed in this work are cut in such a way that a certain plane of the
fcc lattice is perpendicular to the surface normal, i.e. the atoms in the top layer are arranged
in the respective crystal structure. The (111) surfaces exhibit a hexagonal structure and three
dense-packed directions. In high resolution STM images these structures can be resolved. In
fig. 2.9a,b STM images of the Cu(111) and Ag(111) surfaces are shown, respectively. Their lat-
tice constants amount to 2.56 A(Cu) and 2.89 A(Ag). [61]
Figure 2.9: STM images with atomic resolution of the three different crystals employed: a) Cu(111), b) Ag(111),c) Ag(100). [5.5 × 2.1 nm2; a) -0.02 V, 3.7 nA; b) -0.96 V, 0.11 nA; c) -0.6 V, 0.13 nA]
The (100) surface is four-fold symmetric with two-dense packed directions that are perpendicu-
lar to each other (fig. 2.9c). The lattice constant amounts to 2.89 A as well.
18 2 EXPERIMENTAL METHODS
Sample holder
The crystal is fixed on an oven mounted on the sample holder (see fig. 2.10). A molybdenum
(Mo) ring holds the crystal on the oven and a tantalum (Ta) wire (diameter 0.5 mm) coiled
around the oven is connected to the Cu heating wires. The heating current required to heat
the sample to 720 K is typically around 2.6 A. The temperature of the sample is measured by
a K-type thermocouple which is attached to the Mo ring in close proximity of the crystal sur-
face. All four cables, the two Cu wires required for heating and the two thermocouple wires are
soldered to metal contacts on a ceramic plate at the back of the sample holder. If the sample
holder is grabbed on the manipulator, metal springs are pressed against the metal contacts so
that the sample can be heated and the temperature can be measured. If the sample is placed
in the STM, it is contacted to establish the bias between tip and sample.
Figure 2.10: Sample holder with a crystal mounted on the oven which can be heated with the Cu heating wires.Adapted from [69].
Preparations
During the different sample preparations described in the following chapters the molecules are
evaporated from the OMBE onto the cleaned crystal. Before depositing molecules for the first
time under UHV conditions they need to be degassed in order to evaporate all remaining sol-
vents or catalysts that are not desired on the surface. The degassing time and temperature
depends on the molecule and its synthesis. For each experiment the temperature of the crucible
Tcru, deposition time td, sample temperature TS during deposition and the resulting coverage
are given in table 1 (tab.) and in the respective chapter.
For the experiments addressing the interaction of porphyrins with gaseous ligands, small gas
molecules (CO and O2) are dosed via a leak valve by backfilling the whole chamber to pressures
2.1 Scanning Tunneling Microscopy 19
Molecule Substrate Tcru (K) TS (K) td (min) Coverage (% ML)
2H-P Ag(111) 470 350 30 0.22H-P Ag(111) 510 300 30 12H-P Ag(111) 510 530 90 0.592H-P Ag(111) 510 570 90 0.452H-P Ag(111) 510 610 90 0.342H-P Ag(100) 520 300 3 0.442H-P Ag(100) 500 640 30 0.76Co-P Ag(111) 540 300 5 0.17Co-P Ag(111) 530 300 30 0.62
Trans-Br-P Ag(111) 520 180 5 sub-MLCis-Br-P Ag(111) 520 250 5 sub-ML2H-TPP Ag(111) 600 300 4 to 7 sub-ML
DPP Ag(111) 560 300 1 sub-MLFePc Cu(111) 680 300 30 sub-ML
BO-ADPM Ag(111) 490 300 23 sub-MLC60 Ag(111) 690 320 50 sub-ML
Table 1: Evaporation parameters for all molecules used in this work. Abbreviations: ML: monolayer, 2H-P:Free-base porphine, Co-P: Co-porphine, Trans-Br-P: 5,15 Dibromoporphine, Cis-Br-P: 5,10 Dibromoporphine, 2H-TPP: Tetraphenylporphyrin, DPP: 5,15 Diphenylporphyrin, FePc: Fe-Phthalocyanine, BO-ADPM: B,O-chelatedazadipyrromethene.
between 5 · 10−8 to 3 · 10−7 mbar. In most of the experiments the sample is kept inside the STM
chamber. During gas dosage the shutter in front of the cryostat is opened and the sample warms
up to approximately 20 K.
One layer of insulating boron nitride (BN) can be grown on the Cu(111) surface by chemical va-
por deposition of borazine (HBNH)3. The chamber is backfilled with borazine (p: 1 ·10−7 mbar)
for 5 min while the sample is held at approximately 1030 K and cooled down slowly after the gas
dosage. A detailed description is given in refs. [70, 71].
After the respective preparation the sample is cooled on the manipulator by liquid helium with
a cooling rate of approximately 1 K/s. When the sample reached a temperature of 100 K it is
transferred to the STM chamber where it is further cooled to 6 K.
The molecules 2H-P and Co-P were purchased from Frontier Scientific, 2H-TPP and FePc from
Sigma-Aldrich, DPP from PorphyChem and C60 from Alfa Aesar. The trans-Br-P and cis-Br-
P were synthesized by Thien H. Ngo (National Institute for Materials Science, Japan). The
synthesis of BO-ADPM is described in ref. [72].
20 2 EXPERIMENTAL METHODS
2.2 Complementary methods
In the following, experimental techniques that were not applied by the author, but uti-
lized by coworkers in order to gain a more comprehensive understanding, are briefly introduced.
The combination of several surface-sensitive techniques allows a more profound characterization
of the different systems than afforded by STM measurements only. The spectroscopic meth-
ods of near edge X-ray absorption fine structure spectroscopy (NEXAFS), X-ray photoelectron
spectroscopy (XPS) and ultraviolet photoelectron spectroscopy (UPS) enable to probe a wide
range of unoccupied and occupied states and to determine the elemental and chemical compo-
sition of adsorbates as well as their orientation relative to the underlying surface. Moreover, in
temperature-programmed desorption (TPD) measurements the occurrence of chemical reactions
on surfaces can be monitored, e.g. by recording the desorption of hydrogen or molecular frag-
ments. Finally, density functional theory (DFT) gives the opportunity to model and interpret
experimental results.
2.2.1 Near edge X-ray absorption fine structure spectroscopy
Near edge X-ray absorption fine structure spectroscopy (NEXAFS) is a spectroscopic method
that probes electronic states of adsorbates on different surfaces. In molecules both electronic and
geometric properties are determined by exciting inner shell electrons into unoccupied molecular
orbitals with linearly polarized soft X-rays. This method is particularly suited for the charac-
terization of atoms with a low atomic number Z, as e.g. C, O and N which are present in most
organic compounds. [73,74]
In the NEXAFS technique, the X-ray absorption is recorded as a function of the photon energy
at a certain absorption edge. Radiation with tunable energy, high brilliance and well-defined
linear polarization are needed. Synchrotron radiation fulfills these requirements in an optimal
way.
In general, the dominant processes in the energy range of soft X-rays are photoabsorption and
-emission. If a core electron is excited in the irradiated material it leaves behind a core hole
which is subsequently filled by an electron from a higher energy level. This second process ei-
ther occurs radiatively by emission of a fluorescence photon or nonradiatively by emission of an
Auger electron. [73] Both the emitted photons and electrons can be used to detect the excitation
of a core electron at a particular energy of the X-rays, such that the absorption probability is
monitored. In the following, only the detection of electrons is considered since they give a higher
yield than fluorescence photons for low Z molecules.
For NEXAFS, the energy of the X-rays is chosen in such a way that core electrons are excited
into unoccupied states of the adsorbates which are slightly below and above the ionization en-
ergy. Due to the low inelastic mean free path of electrons in matter, the electrons leaving the
surface come from a depth of a few nanometers or less. Thus, this method is sensitive to sur-
2.2 Complementary methods 21
faces and subtraction of the signal from the substrate allows a characterization of the adsorbates.
NEXAFS measurements in the electron yield mode require UHV to minimize energy losses of
the ejected electrons. Furthermore, in this environment unwanted contamination of the sample
surface with molecules and atoms from the residual gases is significantly reduced.
Figure 2.11: Absorption signal for NEXAFS: Excitation of core electrons into the unoccupied molecular orbitalsof a diatomic molecule induced by soft X-rays. π? resonances usually lead to sharp peaks in the absorptionspectrum, while σ? states above the vacuum level exhibit a broader line shape.
The excitation of a core electron of an adsorbed diatomic molecule is depicted in fig. 2.11. An
electron in the 1s level of one of the atoms is excited into an unoccupied molecular orbital by
absorption of a photon of given energy. The π? states lie below the vacuum level. Thus, if
the energy of the incoming photons matches the energy difference between the core level and
the unoccupied π? state, resonant excitation occurs and secondary electrons following core hole
decay are detected resulting in a sharp peak in the absorption spectrum. As soon as the photon
energy reaches the ionization threshold of a particular atomic core level an abrupt ionization
step is observed in the absorption spectrum. Since σ? states often lie above the vacuum level
the respective resonances are superimposed with the ionization step. Moreover, they generally
exhibit a broader line width than the π? states. Recording the NEXAFS spectra across the K-
edges of all atoms present in the adsorbate molecules enables to analyze the electronic structure
of the molecules and the bonds between the atoms in the molecule, as the unoccupied molecular
orbitals are bond-specific. [73–75]
Another notable feature of NEXAFS is the angle-resolved measurement of the absorption prob-
ability which can provide information about the geometric orientation of molecules or of specific
functional groups. The absorption of linearly polarized X-rays is maximized if the vector of the
22 2 EXPERIMENTAL METHODS
electric field of the electromagnetic radiation is parallel to the main axis of an orbital, whereas
it is minimal if the electric field vector is perpendicular to the main axis of an orbital. Thus, by
recording the absorption probability at different angles between normal and grazing incidence,
the orientation of selected molecular orbitals relative to the surface can be determined.
The NEXAFS data presented here were recorded at the BESSY II storage ring (Berlin, Ger-
many). The emitted electrons were retarded with a bias voltage of -150 V before detection in
order to detect only electrons coming from the surface region (partial electron yield mode, PEY).
For each of the three recorded incidence angles (20, 53 and 90◦) the photocurrent signal of a
contaminated gold grid traversed by the X-ray beam was recorded simultaneously with the PEY
spectra. After the energy scale was referenced against a characteristic peak at 285 eV of the gold
grid spectrum, the signal of a bare Ag(111) crystal was subtracted from the sample spectrum,
followed by correction for the photon flux and normalization of the edge jump to one.
2.2.2 Photoelectron spectroscopy
With photoelectron spectroscopy (PES) the occupied states of adsorbates on surfaces are
probed by irradiation with photons. This method gives element-specific information and is
highly surface-sensitive. [8, 76]
If a material absorbs photons with a certain energy, bound electrons can be emitted and leave
the material with a given kinetic energy. This phenomenon, known as the photoelectric effect,
was first observed by H. Hertz in 1887. [77] Under the condition that the energy of the photons
~ω is large enough to overcome the work function φ of the material and the binding energy EB
of the respective electron, the kinetic energy of the emitted electron is given by:
Ekin = ~ω − φ− |EB| .
The work function can be determined by the energy cut-off, where Ekin = 0. If φ is known, the
binding energy of the emitted electrons can be calculated from their kinetic energy.
The photo emission spectrum, i.e. the intensity of emitted electrons plotted as a function of the
kinetic energy, can be evaluated on the one hand qualitatively since the binding energies of core
level peaks are element-specific. As a result, the composition of the first few layers of the sample
can be determined. Similar to NEXAFS, the escape depth of the emitted electrons is of the
order of 1 nm which renders PES surface-sensitive as well. Furthermore, a PES spectrum gives
information about the relative amount of detected species by their different peak intensities.
Typically, one distinguishes between two variants of PES: X-ray photoelectron spectroscopy
(XPS) employs X-rays (100 eV to 10 keV), while ultraviolet photoelectron spectroscopy (UPS)
uses UV photons with energies between 5 and 100 eV.
For XPS experiments either a laboratory X-ray source is used or synchrotron radiation generated
in a storage ring. In the latter case, a monochromator selects photons of well-defined energy
before the beam impinges on the surface. The emitted electrons are detected by an electron
2.2 Complementary methods 23
energy analyzer. Due to the short mean free path of the electrons all PES experiments are
usually carried out in UHV. The analyzer selects electrons with a specific kinetic energy. More-
over, by applying a retarding voltage to the electron lens system at the entrance of the analyzer
the kinetic energy can be scanned in a pre-determined interval, such that the Intensity(Ekin)
spectrum is measured.
Because of the high energy of X-rays, XPS probes core levels of atoms. These levels are element-
specific and they also vary moderately in energy depending on the chemical environment of the
emitter atom. Thus, the chemical state of atoms in molecules can be determined.
In contrast, for UPS lower energy photons are provided either by a gas discharge lamp or by
a synchrotron light source. With this method, the energy-dependent DOS of the valence band
can be resolved with much higher resolution than for XPS. [76]
The UPS data shown in ch. 3.1.2 was recorded at the Materials Science beamline of the ELET-
TRA storage ring in Trieste, Italy. The UHV chamber is operated at a base pressure of
2 ·10−10 mbar and is equipped with a SPECS PHOIBOS 150 electron energy analyzer of 150 mm
mean radius fitted with a 1D-DLD detector. The light was linearly polarized with an energy of
30 eV and an energy resolution of 0.13 eV was employed. The electron detection geometry was
varied between normal and grazing emission (60◦ off-normal, corresponding to normal incidence
of the photon beam) with an acceptance angle of ±7◦.
The XPS data presented in ch. 6.3 was recorded with a laboratory Al Kα X-ray source in grazing
electron emission geometry. The UHV chamber exhibits a base pressure of 8 · 10−11 mbar and is
equipped with a hemispherical electron analyzer (Phoibos 100 CCD by SPECS).
2.2.3 Temperature-programmed desorption
During a temperature-programmed desorption (TPD) experiment the desorption of selected
atoms or molecules is detected with a mass spectrometer while the sample is heated in a con-
trolled way with a linear heating-ramp. This technique enables to determine the characteristic
desorption temperature for atoms or molecules from a certain surface. In our specific case, by
detecting the hydrogen (H2) evolution, the occurrence of chemical reactions involving the release
of hydrogen can be evidenced.
The TPD experiments presented here were carried out in a separate custom-built UHV sys-
tem using a liquid nitrogen cooled quadrupole mass spectrometer with a Feulner cup [78] that
can be brought within a few millimeters of the sample. The heating rate was controlled by
a proportional-integral-derivative controller and kept constant within < ±0.1 K/s. The pres-
sure during TPD measurements was between 2 to 8 · 10−11 mbar and typically the background
pressure of H2 was on the detection limit of the mass spectrometer before TPD measurements
begin.
24 2 EXPERIMENTAL METHODS
2.2.4 Computational details
Most of the structural models shown in the following are obtained with the Software Hyper-
Chem. [79] The geometry optimization was carried out either with the semiempirical AM1 and
extended Huckel methods or molecular mechanics (MM+) simulations. Moreover, frontier or-
bitals are calculated using extended Huckel methods.
Several experimental findings of this work are corroborated and complemented by density func-
tional theory (DFT) calculations. In ch. 3.1.2 the calculations of the electronic structure of por-
phines were performed using the software package StoBe, [80] which describes the Kohn-Sham
orbitals by a linear combination of Gaussian type orbitals. The molecules are isolated (without
surface) for all calculations and a revised Perdew, Burke and Ernzerhof (RPBE) exchange-
correlation functional was used. [81, 82] These basis sets were used for the calculation of the
shape of the frontier orbitals and their energetic separation.
The calculations discussed in ch. 4.1 were performed using the Gaussian Software package with
the 6-311G basis in combination with Perdew-Burke-Ernzerhof (PBE) [81] exchange and cor-
relation functionals. The different molecular structures were optimized towards the minimal
ground state energy and the calculations were carried out in gas phase for an isolated molecule,
using the default convergence criteria of the program.
25
3 Covalent coupling of porphines
Covalent nanostructures composed of functional molecules are of great importance for molec-
ular electronics, optoelectronics and light-harvesting. [22,25,26,83–85] They enable to overcome
the limitation for minimal structure sizes and a precise control of the electronic properties of
a device. The advantage of forming such structures artificially on well-defined surfaces is that
these systems can be characterized with sub-molecular resolution in an UHV environment by
local probe techniques. [86, 87]
Porphyrins on metal surfaces as well-studied systems [40, 88–91] are a promising candidate for
the formation of covalent nanostructures on the one hand due to their versatile and tunable
properties and on the other hand because covalently fused porphyrin tapes can already be syn-
thesized in solution. [92–95] These tapes were shown to exhibit exceptional electronic features
- a decreasing band gap with increasing tape length [93, 94, 96] - and nonlinear optical prop-
erties. [94, 97] Furthermore, calculations suggested that fused porphyrins can be employed as
molecule-sized memory units [98] or for efficient excitation energy transfer. [85] Thus, it is desired
to create these tapes on surfaces as well. As spray deposition techniques still exhibit practical
limitations, [99,100] the synthesis of covalent networks under UHV conditions on metal surfaces
is aimed for and was realized for a range of different molecules [25, 26] and for porphyrins as
well. [86, 101,102]
In this chapter, the thermally-induced and surface-assisted covalent coupling of porphine molecules
on Ag surfaces is described. The porphine molecule is the macrocycle of each porphyrin [103–105]
and it can either host two hydrogen atoms in the center (free-base) or a metal ion which can be in-
corporated in the macrocycle on the surface by codeposition of a metal (similarly to tetraphenyl-
porphyrins [89, 106–108]). It is shown, that triply- and doubly-fused porphine tapes can be
formed on the Ag(111) and Ag(100) surfaces in a certain temperature range under the condition
of a high coverage of molecules on the surface. Because of the extended conjugated π-systems of
these oligomers the electronic properties are modified and similarly as in solutions a reduction
of the band gap is observed. The same reaction can be induced for a metal porphine with a
Co center, however the free-base and the Co-porphine exhibit different preferred binding motifs.
Finally, a common method for the formation of ordered covalent nanostructures is the substitu-
tion of hydrogen atoms by halogen atoms at certain positions of the molecule so that a directed
growth can be achieved. The halogen-C bond is dissociated at lower temperatures on metal sur-
faces than the C-H bond leading to a directed growth of nanostructures. [25,26,86,102,109,110]
This approach, referred to as Ullmann coupling, is employed for porphine molecules with two Br
atoms as substituents. On the Ag(111) and Ag(100) surfaces the Br-porphines are observed to
form metal-organic chains (via Ag coordination) and at higher substrate temperatures covalent
structures.
26 3 COVALENT COUPLING OF PORPHINES
3.1 Free-base porphine on Ag(111)
In ref. [104] it is shown that after room temperature (RT) deposition of free-base porphine
(2H-P) onto a Ag(111) surface the molecules are arranged as dispersed monomers, if the cover-
age is below 0.8 monolayers (ML, definition of one ML is given in [104]). The molecules do not
assemble in a regular pattern because of a repulsive interaction between them which is caused
by a charge transfer from the substrate. [104]
Figure 3.1b shows 2H-P molecules on Ag(111) with a coverage of 0.2 ML (Tcru = 470 K, TS =
350 K and td = 30 min, STM image acquired by Felix Bischoff). As depicted in fig. 3.1a, the
two central hydrogen atoms impose a symmetry axis on the 2H-P molecule. This principal
symmetry axis of the molecule (marked with dotted line) is always oriented perpendicular to
one of the three dense-packed directions of the underlying substrate. The molecule appears
square-like in STM images (see fig. 3.1a) with a depression in the center. The two protrusions
on the macrocycle at the position of the pyrrolic nitrogen atoms (N-H) enable to identify the
principal symmetry axis of the molecules in STM images as well as tautomers. [23, 104]
Figure 3.1: 2H-P on Ag(111). a) STM image of a monomer with structural model. The symmetry axis givenby the central hydrogen atoms is perpendicular to the dense-packed direction [1-10] of the crystal. C, N, and Hatoms are indicated in cyan, blue, and white, respectively. b) Room temperature deposition: Molecules are singlydistributed over the surface. c) After annealing at 570 K: Monomers (blue circle), dimers (green circle) and a fewoligomers (e.g. trimers, yellow circle) are observed. b) adapted from [104] and a,c) from [111]. [a) 2.5 × 2.5 nm2,-0.15 V, 0.12 nA; b,c) 22.1 × 22.1 nm2; a) -0.2 V, 0.1 nA b) -0.8 V, 0.2 nA; c) -0.2 V, 0.1 nA]
3.1.1 Homocoupling
In order to couple 2H-P molecules covalently, two different approaches are employed. In the
first approach, slightly more than one ML of 2H-P is deposited onto a Ag(111) surface (Tcru =
510 K, TS = 300 K and td = 30 min) and annealed at 570 K for 20 min. This preparation results
in a sub-ML of monomers, dimers and a few oligomers (marked by circles in fig. 3.1c). The
3.1 Free-base porphine on Ag(111) 27
most abundant oligomer is the dimer shown in fig. 3.2a. Its center-to-center distance amounts to
8.5±0.3 A which is significantly less than measured and calculated for organo-metallic coupling.
In ref. [112] it is shown that Cu-P molecules couple via Cu adatoms on a Cu(110) surface with
a center-to-center distance between two porphine units of 10.8 A. On the other hand, geometry
optimization, based on the semi-empirical AM1 method in the framework of the Hyper-Chem
package, [79] gives a center-to-center distance of 8.5 A for a covalently coupled dimer as shown
in fig. 3.2a. The same number is obtained by geometry optimization carried out with the DFT
code StoBe (see below). Thus, it is assumed that upon annealing dehydrogenation reactions
take place at the periphery of the molecule and that the macrocycles couple covalently via C-C
bonds.
Figure 3.2: Three different binding motifs for covalent coupling of 2H-P on Ag(111): STM topograph andtentative structural model. a) First motif: β − β,meso−meso, β − β. b) Second motif: meso− β, β −meso. c)Third motif: β − β,meso− β. Adapted from [111]. [2.5 × 2.5 nm2, -0.15 V, 0.12 nA]
Overall, three different binding motifs are observed which are depicted with their respective
tentative model in fig. 3.2. The structural models obtained with Hyper-Chem are assigned by
comparison to the STM images. The first binding motif (β − β,meso − meso, β − β, named
after the hydrogen positions marked in fig. 3.1a) involves six dehydrogenation reactions and the
formation of three C-C bonds between the two porphine units (see fig. 3.2a), since the edges of
the dimer are collinear. The second binding motif (meso − β, β −meso) is attributed to four
dehydrogenation reactions and the formation of two C-C bonds (see fig. 3.2b) resulting in an
offset of 2.2± 0.5 A between the two porphine units. The two protrusions marking the symme-
try axis of the molecules are still visible in the oligomers, thus the orientation of the porphine
units in the oligomers towards the substrate can be determined. Within the precision of the
measurement (±5◦), for motif 1 and 2 both units are oriented along the dense-packed directions
of the crystal (marked in fig. 3.5a) in the same way as the monomers.
Finally, the third binding motif (β − β,meso − β) is assumed to involve four dehydrogenation
reactions and the formation of two C-C bonds (see fig. 3.2c). The formation of only a single
28 3 COVALENT COUPLING OF PORPHINES
C-C bond in this motif is excluded because of disagreement of the images with models involving
a single bond. In contrast to the first two binding motifs, only one of the porphine units in
the third binding motif is oriented along the dense-packed directions of the crystal. The second
unit deviates by approximately 15◦ from these crystal directions, resulting in an angle of 45◦
between the two units. Similarly, the gas phase geometry optimization of the third binding
motif by Hyper-Chem yields an angle of 45◦ between the two porphine units. Consequently, the
covalent interaction between the molecules is stronger than the site-specific molecule-substrate
interactions since one of the porphine units deviates from its preferred adsorption site. The fact
that the same covalent coupling reactions are observed on a surface with a different geometry,
namely the Ag(100) surface, supports the conclusion that the substrate does not enforce the
particular conformations of the oligomers (see also ch. 3.2).
Additionally, species of the size of a monomer and a greater apparent height are observed after
annealing (marked with blue dotted circle in fig. 3.1a and shown in fig. 3.3). Their appearance
is cross-like at negative biases (fig. 3.3a) and rhombic at positive sample biases (fig. 3.3b). The
dI /dV spectrum of the brighter species shows a clear peak around -0.1 V whereas the spectra
acquired on 2H-P molecules are nearly featureless (see fig. 3.4). In good agreement with the
dI /dV spectra, the dI /dV maps show pronounced differences between the bright species and a
2H-P monomer. At -0.1 V the bright species exhibits a cross-shaped state whereas the monomer
appears dim (fig. 3.3c,d). In comparison, fig. 3.3f shows a difference in the electronic structure
between the two monomers at a different bias as well.
Figure 3.3: Bright monomer species assigned to 2H-P interacting with one Ag atom. a) Cross-shaped appearanceat negative bias and b) square-shaped appearance at positive bias. c) Topography image and d) dI/dV mapshowing a pronounced state on the bright monomer species and less density of states for the monomer and dimer.e) Topography image and f) dI/dV map indicating clear differences between the three species at another bias. g)Dimer and h) trimer interacting with Ag atoms. [a,b) 2.5 × 2.5 nm2, c-f) 4.5 × 4.1 nm2, g) 2.7 × 2.1 nm2, h) 3.7× 2.1 nm2, a) -1.8 V, 0.09 nA, b) 0.35 V, 0.2 nA, c,d) -0.1 V, 0.2 nA, e,f) -0.4 V, 0.2 nA, g,h) -1.4 V, 0.09 nA]
Due to the similarity in the topographic appearance to other metalated porphines such as Co-P
3.1 Free-base porphine on Ag(111) 29
(see ch. 3.3) the brighter species are assigned to 2H-P molecules that reacted with a Ag atom.
Since these species exhibit a range of different apparent heights there might be different con-
figurations of the Ag atom in the center of the macrocycle. As shown in fig. 3.3h,i not only
monomers can incorporate a Ag atom into the macrocycle but also oligomers.
Figure 3.4: Scanning tunneling spectra (dI/dV ∝ DOS) on the bare metal (black line), on the center of a 2H-Pmonomer (green line) and on the center of a bright monomer (red line). In agreement with the dI/dV map at-0.1 V in fig. 3.3d a peak is present around this bias for the bright 2H-P species but not for the 2H-P.
Employing this first approach to covalently couple porphine molecules 49± 2 % of all molecules
reacted to form oligomers. The average oligomer length is 2.1 ± 0.3 porphine units and the
oligomer coverage is 0.11 ± 0.02 ML of 2H-P. The efficiency of the reaction could not be im-
proved considerably by a prolongation of the annealing time because the reaction on the surface
is limited by desorption of the molecules. At 530 K the desorption rate for monomers amounts
to 3 % ML/min. Thus, the amount of reactants on the surface is limited by desorption.
Therefore, in the second approach a continuous supply of molecules onto the heated surface is
applied that counteracts the desorption. Three different substrate temperatures during depo-
sition are employed (530, 570 and 610 K) and the deposition time is 90 min for all cases. As
depicted in fig. 3.5a,b this procedure results in a sub-ML of monomers and oligomers although
TS is lower than in the first approach. For the same temperature as employed in the first ap-
proach the percentage of molecules bound in oligomers is clearly increased from 49 % to 80 %
(fig. 3.5c,d). A further increase of TS to 610 K during deposition of molecules leads to an average
oligomer length of 8.2 porphine units and 97 % of the molecules are nonmonomers (fig. 3.5e,f).
However, the surface coverage of oligomers stays approximately constant for the three different
temperatures of the second approach (see tab. 2 for details). Thus, the second approach enables
to increase the average oligomer length and the percentage of molecules bound in oligomers.
Furthermore, a higher coverage of oligomers is achieved. Table 2 summarizes the statistical
analysis.
30 3 COVALENT COUPLING OF PORPHINES
Figure 3.5: Deposition of 2H-P on heated substrate (Ag(111)) at three different substrate temperatures TS : a,b)TS = 530 K; c,d) TS = 570 K; e,f) TS = 610 K. The percentage of reacted molecules and the average length ofoligomers increases with increasing TS . The solid lines give the dense-packed directions of the crystal. Adaptedfrom [111]. [a,c,e) 12.6 × 7.3 nm2; b,d,f) 28.1 × 16.4 nm2; a) -0.5 V, 0.3 nA; b) 1.21 V, 0.3 nA; c,d) -1.8 V, 0.07 nA;e) -1 V, 0.09 nA; f) -0.7 V, 0.1 nA]
Substrate temperature TS 530 K 570 K 610 K
Average oligomer length 2.1± 0.3 2.7± 1.3 8.2± 10.8
Coverage 59± 4 45± 4 34± 4Monomer coverage 29± 4 9± 2 1± 0.5Oligomer coverage 30± 4 35± 3 33± 3
Percentage of nonmonomers 51± 2 80± 3 97± 3
Binding motif 1 81± 5 74± 5 67± 6Binding motif 2 13± 3 12± 3 14± 5Binding motif 3 6± 3 14± 3 20± 5
Table 2: Statistical analysis of average oligomer length, coverages, percentage of nonmonomers and occurrenceof the three binding motifs in dependence of the substrate temperature during deposition. Coverages are givenin % of one ML of 2H-P on Ag(111) which is defined in [104]. Errors correspond to standard deviation.
As well as for the first approach three different binding motifs are observed in the oligomers ob-
tained by the second approach. The first binding motif is clearly abundant at all three substrate
temperatures, however, it slightly decreases with increasing temperature from 81 % to 67 % (see
tab. 2). The second motif stays constant within the error bars and the occurrence of the third
motif increases with temperature from 6 % to 20 %. This behavior seems counterintuitive on first
sight since the first motif involves six dehydrogenation reactions and the other two motifs only
four. Furthermore, no singly-fused oligomers were observed. At first, an adsorption-site deter-
mined reaction can be excluded because within the precision of the modeling none of the binding
motifs is commensurate with the lattice of the crystal. Another explanation for the preferred
occurrence of motif 1 can be found in the wet chemistry approach for synthesizing porphyrin
tapes. As an intermediate meso − meso linked porphyrins are synthesized due to the meso
3.1 Free-base porphine on Ag(111) 31
position being more reactive than the β positions. [92, 113] If this property is preserved on the
Ag surface the reactivity of the meso position can be an explanation of the preferred occurrence
of motif 1. Once the meso positions reacted to form a C-C bond between two molecules the
steric hindrance of the remaining hydrogen atoms at the β positions results in strain-facilitated
dehydrogenations and the formation of the other two C-C bonds yielding motif 1. The partial
lifting of the molecule or rotation around the meso C-C bond seems feasible at these substrate
temperatures where considerable amounts of molecules desorb. In accordance with this expla-
nation is the increasing occurrence of motif 3 with temperature since more energy is available
for dehydrogenation at the less reactive positions.
Generally, eliminative on-surface reactions involve diffusion of the reactants, dehydrogenation or
dehalogenation and covalent coupling. The dehydrogenation or dehalogenation can occur upon
adsorption followed by the diffusion of the radicals which covalently couple when they come
close enough. [26, 28, 86, 102] Another possibility involves the diffusion of the unreacted educts
and only when two educts are close to each other dehydrogenation and covalent bond formation
take place. [114, 115] In the case of 2H-P on Ag(111) it is observed that firstly, the surface is
decisive for the reaction. The energy required to cleave the C-H bond in vacuum amounts to
4.5 eV [116] which is significantly more than the thermal energy available during the reactions on
the surface, thus the surface acts as a catalyst for the reaction. Furthermore, no oligomers are
observed if the surface temperature is below 470 K, thus the reaction does not take place in the
crucible. Secondly, the coverage of molecules on the surface during the reaction is decisive for
the efficiency of the reaction. In the first approach the coverage decreases with time which limits
the amount of available educts. The second approach provides a high coverage of molecules over
the entire reaction time. It was also observed for another on-surface reaction that the coverage
plays an important role. [117] However, in the first approach the coverage is high at the begin-
ning of the annealing time. Nevertheless the first approach is less efficient. With these findings
it cannot be stated how the on-surface reaction takes place. If all molecules dehydrogenated
already upon adsorption, only radicals should be present after annealing. However, as depicted
in fig. 3.6 it is not possible to distinguish between porphine radicals and unreacted porphines in
STM images. Figure 3.6c,d show that the appearance in STM of a thermally debrominated 5,15
Dibromoporphine is very similar to a RT deposited 2H-P (fig. 3.6a) as well as to 2H-P deposited
onto a heated sample (fig. 3.6b).
The objective to form extended oligomers is achieved by employing the second approach. As
shown in fig. 3.5f oligomers consisting of up to 90 porphine units are observed. Nevertheless, the
covalent nanostructures lack order. Figure 3.7a,b depicts the most abundant trimers, c and d
appear less frequently. Even though the triply-fused dimer is formed preferentially most of the
longer oligomers do not exhibit the straight shape of porphyrin tapes but involve many turns
and angles. Thus, a more directed growth of oligomers is required in order to form extended and
regular nanostructures. One method to achieve directed growth is to substitute some hydrogen
32 3 COVALENT COUPLING OF PORPHINES
Figure 3.6: a) 2H-P on Ag(111) after RT deposition (adapted from [104]) and b) after deposition onto a heatedsample. There is no clear difference in appearance to thermally debrominated 5,15 di-bromoporphine (c,d).Adapted from [111]. [1.6 × 1.6 nm2; a) -0.8 V, 0.2 nA, b) -0.7 V, 0.1 nA, c) -0.8 V, 0.08 nA, d) -0.1 V, 0.1 nA]
atoms at the periphery of the molecule with halogen atoms which are more reactive. A wide
range of examples can be found in literature [26, 86, 102, 109] and one example involving the
porphine is shown in ch. 3.4.
Figure 3.7: Different trimers observed for the second approach. a,b) Most abundant motifs. c,d) Less frequentlyobserved motifs. Adapted from [111]. [3.8 × 3.2 nm2; -1.8 V, 0.07 nA]
3.1.2 Electronic structure and physical properties
In order to further characterize the porphine oligomers, space-averaging techniques were em-
ployed. Katharina Diller carried out the NEXAFS measurements and simulations and the DFT
calculations. Francesco Allegretti supervised the UPS measurements.
Figure 3.8c shows the NEXAFS spectrum recorded on a sub-ML of porphine monomers on
Ag(111). Its similarity to the spectrum of a multilayer points to a weak modification of the
spectrum by the charge transfer from the substrate to the molecules in the first layer. [104]
Consequently, the calculated magic angle curve (fig. 3.8g) agrees well with the measured one
(fig. 3.8e). For a sample prepared via the second approach at TS = 610 K, i.e. nearly all
molecules are bound in oligomers, the NEXAFS spectrum shows pronounced differences (see
fig. 3.8d). The first peak is quenched while the angular dependence is similar. These changes
have often been attributed to a partial filling of the LUMO from the substrate. [105,118] On the
other hand, the DFT calculation of the NEXAFS spectrum of the triply-fused dimer (fig. 3.8h)
is very similar to the experimental one (fig. 3.8f) although the calculations do not involve any
substrate. Therefore, the NEXAFS spectra point towards a chemical change of the oligomers in
3.1 Free-base porphine on Ag(111) 33
comparison to the monomers rather than a modified interaction with the substrate. However,
it should be emphasized that in the experiment oligomers of different length and with different
binding motifs are present on the surface whereas the calculations only involve a single triply-
fused dimer.
The vanishing π∗ resonance in the 90◦ curve for both the monomer and the oligomer sample
imply a flat adsorption of the molecules for both cases.
Figure 3.8: Experimental and simulated C K-edge NEXAFS spectra of 2H-P monomers (RT deposition) on theleft and oligomers (deposition at TS = 610K) on the right. Red dots in the structural models of the 2H-P monomer(a) and dimer (b) mark the inequivalent C and N atoms which were taken into account for the calculations. c,d)Angle-resolved spectra with gray areas indicating the zoomed-in region shown in e and f. g,h) Simulated spectrain the same energy range as e,f. Taken from [111].
The electronic states of the triply-fused dimer as the most abundant coupling motif are probed
by STS and UPS. Similarly to the monomer the dI /dV curves show no pronounced states for
dimers either. In contrast, dI /dV maps show a clear difference between monomers and dimers.
Figures 3.9 and 3.10a to d show the topography and the dI /dV signal at different negative
biases, which means that the occupied states of the molecules are probed. At -0.45 V the dimers
exhibit a pronounced state in the center whereas the monomers appear darker. The state of the
dimer appears in a broad range of biases from -0.55 to -0.25 V. A possible explanation why this
peak is not observed in dI /dV curves is that the peak is too broad due to interaction with the
34 3 COVALENT COUPLING OF PORPHINES
substrate.
Figure 3.9: a) STM topography image and b) simultaneously recorded dI/dV map at -0.45 V. A two-lobed stateis present on the center of the two dimers whereas the monomers exhibit less contrast at this bias. Adaptedfrom [111]. [11 × 5.3 nm2; 0.21 nA]
The occupied states are also probed by UPS on a sample which is prepared at TS = 570 K result-
ing in 80 % of the molecules bound in oligomers. In comparison to the monomer sample (green
line in fig. 3.11) the oligomer sample (blue line) shows additional peaks in the UP spectrum.
For the monomers a clear HOMO state is observed at 2.2 eV and the LUMO is shifted partially
below the Fermi level because of a charge transfer from the substrate indicated by a small peak
close to the Fermi level. [104] The LUMO is shifted even further below the Fermi level for the
oligomers as marked by the blue bar and the HOMO is shifted closer to the Fermi level to 1.5 eV
which results in a reduced band gap for the oligomers. The HOMO peak of the monomers is
visible as well in the oligomer spectrum since 20 % of the molecules are still monomers.
Figure 3.10: Electronic states of the triply-fused dimer. a) to d) STM topography images and dI/dV maps atdifferent biases. a) -0.55 V, b) -0.45 V, c) -0.35 V, d) -0.25 V. e) STM images of the HOMO and the LUMO obtainedby Huckel calculations. f) Kohn-Sham frontier orbitals (HOMO and LUMO) calculated using the software packageStoBe. The shape of the state observed in the dI/dV maps resembles the calculated LUMO. Adapted from [111].[2.7 × 3.3 nm2; 0.2 nA]
Figure 3.11b shows DFT calculations of the ground states of the porphine monomer and dimer.
Usually the actual gap values are not reproduced by DFT [119] but the same trend of a reduc-
tion in the band gap is observed. This finding is in good agreement with the observation of a
3.2 Free-base porphine on Ag(100) 35
decreasing band gap for an increasing tape length in solution. [120–123]
Figure 3.11: Band gap reduction upon dimerization. a) UP spectra recorded in grazing emission geometry fora monomer sample (green curve) and a oligomer sample (blue curve, TS = 570K). The black line corresponds toa spectrum on the clean Ag(111) surface. b) DFT ground state calculation of the Kohn-Sham energies for thetriply-fused dimer (blue) and monomer (red). The dimerization leads to a splitting of the degenerate LUMO (L)and LUMO+1 (L+1) orbitals of the monomer. Adapted from [111].
Furthermore, the shift of the LUMO below the Fermi level can be rationalized by the appear-
ance in STM images. In fig. 3.10e charge density contour plots representing the LUMO and
the HOMO of the triply-fused dimer are shown which are obtained by extended Huckel calcula-
tions. [124] The waist of the molecule is broadened for the LUMO and narrow for the HOMO.
Similarly, the calculated Kohn-Sham frontier orbitals (software package StoBe) exhibit the same
shape for both orbitals (fig. 3.10f). Since the state observed in the dI /dV maps is clearly visible
on the waist of the dimer, it resembles the calculated shape of the LUMO rather than the HOMO
despite being in the occupied domain. Consequently, the shape of the state on the dimer points
to a partial filling of the LUMO as well.
3.2 Free-base porphine on Ag(100)
In order to test the influence of the substrate geometry on the coupling reaction of 2H-P on
Ag, the molecule is deposited onto a Ag(100) surface which has two dense-packed directions and
is four-fold symmetric (see ch. 2.1.5). Room temperature deposition (Tcru = 520 K, td = 3 min)
of 0.44 ML of 2H-P results in singly distributed molecules (see fig. 3.12). Due to the alignment
with the substrate the molecules show two different orientations that form an angle of 90◦.
Several annealing steps are carried out revealing that the desorption rate is significantly smaller
on the Ag(100) surface in comparison to Ag(111). At 600 K it amounts to 0.8 % of a ML/min.
Furthermore, higher temperatures are required to reach the same percentage of nonmonomers
as on Ag(111). The interaction with the substrate is stronger leading to a reduced desorption
36 3 COVALENT COUPLING OF PORPHINES
Figure 3.12: Room temperature deposition of 2H-P onto Ag(100). The molecules are dispersed and show twodifferent orientations due to the two-fold symmetry of the substrate. [24.1 × 14.3 nm2; -0.5 V, 0.2 nA]
rate, therefore mainly the first approach is employed, i.e. a ML sample is annealed after the
deposition of molecules. Varying the annealing temperature and duration shows that the per-
centage of nonmonomers increases with both temperature and time, at least as long as there
are still monomers present on the surface. Moreover, the amount of porphines interacting with
a Ag atom (see fig. 3.3) increases with time and temperature as well.
Figure 3.13: a) 2H-P on Ag(100) after annealing at 620 K for 40 min. Different oligomers and a few monomersare observed. b,c) Two oligomers that are only observed for annealing temperatures above 590 K (on both Ag(100)and Ag(111)). [a) 23.7 × 18.6 nm2; b,c) 4.8 × 4.5 nm2; a,b) -0.6 V, 0.14 nA; c) -0.5 V, 0.1 nA]
Figure 3.13 shows the surface after annealing at 620 K for 40 min with monomers and oligomers
which are mainly dimers. With increasing annealing temperature oligomers with a high sym-
metry are observed as e.g. depicted in fig. 3.13b and c. However, they represent a minority of
the formed oligomers and are observed on the Ag(111) surface as well.
The annealing step on Ag(100) (620 K for 40 min) yields a composition of molecules which shows
3.2 Free-base porphine on Ag(100) 37
similarities to 2H-P deposited onto the Ag(111) surface heated to 570 K during deposition for
90 min. Despite these different preparation procedures both samples yield a similar percentage
of nonmonomers, 86 % on Ag(100) and 80 % on Ag(111), a similar average oligomer length,
2.6 on Ag(100) and 2.7 on Ag(111), and roughly similar total coverages, 0.35 ML on Ag(100)
and 0.45 ML on Ag(111) (see also tab. 3). Given the fact that increasing the annealing time
only leads to a moderate increase in the percentage of molecules bound in oligomers, the above
comparison indicates that a higher temperature is required on the Ag(100) surface than on the
Ag(111) surface in order to achieve the same efficiency of covalent coupling.
Furthermore, the occurrence of the three binding motifs is compared for both surfaces (see
tab. 3). The first binding motif is slightly more abundant on Ag(100) and motif 2 occurs signif-
icantly less often on Ag(100) than on Ag(111). The different adsorption sites on both surfaces
might play a role for the different occurrence of the binding motifs.
2H-P on Ag(100) 2H-P on Ag(111)annealing at 620 K TS = 570 K during deposition
Average oligomer length 2.6± 1.04 2.7± 1.3
Coverage 35± 3 45± 4
Percentage of nonmonomers 86± 5 80± 3
Binding motif 1 80± 6 74± 5Binding motif 2 4± 2 12± 3Binding motif 3 16± 3 14± 3
Table 3: Statistical analysis of average oligomer length, coverage, percentage of nonmonomers and occurrence ofthe three binding motifs for 2H-P on Ag(100) after annealing at 620 K and deposition of 2H-P onto Ag(111) heldat 570 K (see ch. 3.1.1). Coverages are given in % of one ML of 2H-P on Ag(111) which is defined in [104]. Errorscorrespond to standard deviation.
In order to increase the percentage of molecules bound in oligomers, porphines are deposited
onto the Ag(100) surface heated to 640 K for 30 min. This procedure yields no increase of non-
monomers in comparison to annealing at 620 K for 40 min, however longer oligomers are observed
(see fig. 3.14).
Due to bad resolution during all measurements on this sample no statistical analysis of the bind-
ing motifs is carried out. Moreover, some porphines decompose at this temperature (fig. 3.14b)
and also at an annealing temperature of 600 K (fig. 3.14c) and 620 K (fig. 3.14d).
In summary, the covalent coupling reactions take place on the Ag(100) surface as well, how-
ever the desorption rate is significantly smaller and higher annealing temperatures are required.
Therefore, on Ag(111) longer oligomers are formed before the molecules start to decompose at
high temperatures.
38 3 COVALENT COUPLING OF PORPHINES
Figure 3.14: Deposition of 2H-P onto Ag(100) at 640 K. a) Overview STM image: Longer oligomers than at lowertemperatures are observed. b) Some 2H-P are partially decomposed (in the center of the image). Decompositionis also observed at lower annealing temperatures: c) at 600 and d) at 620 K. [a) 16.3 × 13.8 nm2; b) 6.8 × 6.3 nm2;c,d) 3.8 × 3.8 nm2; a,b) -0.7 V, 0.1 nA, c) -0.5 V, 0.2 nA, d) -0.6 V, 0.11 nA]
3.3 Co-porphine on Ag(111)
The incorporation of a metal ion in the center of the porphine molecule changes many prop-
erties such as the interaction with the substrate, the electronic structure or the shape of the
orbitals. In the following, the covalent coupling of a metal-porphine, namely Co-porphine (Co-
P), is studied.
Figure 3.15: Co-porphine deposited onto Ag(111) at RT. a) STM image of a single molecule with b) structuralmodel. The Co atom is indicated in yellow and the main molecular axis in blue. The center of the moleculeappears as a protrusion at all biases. c) Overview STM image of a sub-ML coverage (0.17 ML). The moleculesare dispersed over the whole surface. [a) 1.6 × 1.6 nm2, 0.13 nA; c) 33.5 × 26.9 nm2, 0.13 nA. The sample bias isunknown due to a missing grounding during these measurements.]
For the Co-P a higher evaporation temperature than for the 2H-P is required due to the higher
molecular weight. At first, Co-P is deposited onto the Ag(111) surface held at RT (Tcru = 540 K,
td = 5 min). This preparation procedure results in a sub-ML (0.17 ML) of dispersed molecules,
3.3 Co-porphine on Ag(111) 39
very similar to the case of 2H-P (see fig. 3.15).
The Co-P appears with a protrusion in the center caused by the Co ion. The high resolution
STM image (fig. 3.15a) reveals that the molecule does not appear four-fold symmetric but one
of the molecular axes shows a greater apparent height than the other one (main molecular axis
marked with blue dotted line in fig. 3.15a). This behavior is observed for Cu-P [105] and for
a range of other molecules as well, e.g. metal phthalocyanines (see [125, 126] and ch. 5) and
is attributed to an electronic effect due to different interactions with the substrate for the two
molecular axes. All Co-P are oriented along the dense-packed directions of the crystal with the
main axis perpendicular to the dense-packed directions.
3.3.1 Covalent coupling
Aiming for the formation of covalent bonds between the Co-P molecules a sample with a
higher coverage (0.62 ML, Tcru = 530 K, TS = RT and td = 30 min) is annealed at 570 K for
20 min in a first step. After subsequent cooling to 6 K the molecules are arranged in different
domains consisting of rows of molecules (see fig. 3.16). The rows within the domains are ori-
ented in three different directions pointing to an alignment with the crystal. It is not clear
what the driving force for this arrangement is. The average intermolecular distances amount to
14.5±0.5 A within the rows and 16.5±0.5 A between the rows which is too large for any coupling
between the molecules and also their appearance is not changed in comparison to RT deposition.
Since 2H-P molecules show a coverage-dependent arrangement on the Ag(111) surface, [104] the
higher coverage in comparison to the first RT deposition (see fig. 3.15c) could be an explanation
for the arrangement of the Co-P.
Figure 3.16: STM images of 0.62 ML Co-P on Ag(111) after annealing at 570 K for 20 min. Three differentdomains with rows of molecules oriented in the same direction are present. The driving force for this arrangementis not understood. [a) 47.6 × 47.6 nm2, 0.1 nA; b) 11.9 × 11.9 nm2, 0.2 nA. The sample bias is unknown due to amissing grounding during these measurements.]
Coupling between Co-P molecules is observed for annealing temperatures between 600 and
40 3 COVALENT COUPLING OF PORPHINES
630 K. In order to determine the nature of the bond and the binding motifs structural models of
covalently coupled Co-P oligomers are superimposed with the STM images (see fig. 3.17) since
the binding motifs cannot be clearly distinguished in the images. Due to the good agreement of
the models with the STM image a coupling via Ag atoms can be excluded and the formation of
covalent C-C bonds is assumed.
Figure 3.17: STM image of one Co-P dimer and two trimers: a) without and b) with structural models of thedimer and respective trimers overlaid. Due to the good agreement of the STM image with the structural modelsof covalently coupled oligomers a coordination via adatoms is excluded. Furthermore, the binding motifs in eacholigomer can be determined. [7.1 × 5.1 nm2, -0.65 V, 0.12 nA]
In contrast to the case of the 2H-P, for the Co-P only the binding motifs 1 and 3 are observed
and motif 3 is clearly abundant (96±11 %, the large error is due to small statistics). Two dimers
are shown in fig. 3.18 with their respective structural model.
Figure 3.18: Two binding motifs that are observed for Co-P after annealing on Ag(111) represented by twodimers (STM image and structural model). a) Binding motif 1 (β − β,meso−meso, β − β). b) Binding motif 3(β − β,meso− β). [2.8 × 2.3 nm2, -0.65 V, 0.12 nA]
It is not clear, why the occurrence of the binding motifs is changed drastically in comparison to
the 2H-P. The substrate temperature is slightly higher during annealing and the flux of molecules
during deposition is twice as high as for the 2H-P. However, for the Co-P the covalent coupling is
induced during annealing, after the deposition of the molecules, thus the flux cannot be decisive
for the reaction. Furthermore, the desorption rate of Co-P at these temperatures is very small
3.3 Co-porphine on Ag(111) 41
in comparison to 2H-P. At 600 K no desorption is observed and at 630 K the desorption rate
amounts to 0.019 ML/min which is less than the rate for 2H-P at 570 K. Since the desorption
limits the efficiency for 2H-P coupling, high percentages of nonmonomers can be achieved by
annealing for the Co-P.
Figure 3.19: Overview STM images of Co-P oligomers on Ag(111) formed by two different approaches. a) Thesample is annealed at 630 K for 10 min and b) the sample is annealed at a lower temperature for a longer time (at610 K for 140 min). Both approaches yield the same percentages of nonmonomers and average oligomer length.[20.9 × 16.1 nm2, a) -0.65 V, 0.12 nA; b) -0.9 V, 0.1 nA]
Two parameters are found to influence the percentage of molecules bound in oligomers, namely
the annealing temperature and the duration. At an annealing temperature of 600 K very few
oligomers are observed whereas after annealing at 630 K for 10 min 80±5 % of the molecules are
nonmonomers. Secondly, after annealing a sub-ML of Co-P at 610 K for 20 min only 22 ± 3 %
of all molecules are bound in oligomers whereas annealing at the same temperature for 140 min
yields 82 ± 6 % nonmonomers. Thus, within the error bars, the longer annealing duration at
the lower temperature (610 K) results in the same percentage of nonmonomers as annealing at
a temperature 20 K higher. Moreover, the average length of oligomers is very similar for both
approaches (see fig. 3.19).
These findings do not explain the differences in the occurrence of binding motifs between 2H-P
and Co-P, however as shown in ch. 4.1 the presence of a metal ion in the center of the macrocycle
can change the reactivity of the periphery of the molecule. In order to give a sound explanation
DFT calculations need to by carried out.
3.3.2 In-situ metalation of oligomers
As shown for many different metals porphyrins can be easily metalated on a substrate under
UHV conditions. [36, 89, 106–108] The same procedure is employed to a sample with 2H-P
monomers and oligomers resulting in the metalation of both species with Co (see fig. 3.20d). A
slight preference for the metalation of monomers in comparison to oligomers is observed: 79±4 %
of the monomers are metalated but only 71±5 % of the oligomers. The similarity in appearance
42 3 COVALENT COUPLING OF PORPHINES
(compare fig. 3.20 a to c) and the observation of the same features in dI /dV maps leads to the
conclusion that Co-P oligomers can either be formed by covalent coupling of Co-P monomers
or by metalation of 2H-P oligomers. These two approaches give the opportunity to tune the
structure of the Co oligomers since the occurrence of binding motifs is clearly different for both
approaches.
Figure 3.20: Metalation of 2H-P oligomers with Co. a) Co-P dimer formed upon annealing Co-P at 630 K.b,c) 2H-P dimers formed upon deposition onto the sample heated to 530 K are metalated with Co. The similarappearance of a) to c) points to the formation of the same chemical species during both approaches. d) OverviewSTM image of 2H-P monomers and oligomers metalated with Co. [a-c) 2.8 × 2.3 nm2, d) 46.1 × 30.5 nm2, a)-0.65 V, 0.12 nA; b) -0.5 V, 0.15 nA; c) -0.2 V, 0.1 nA; d) -0.6 V, 0.12 nA]
In the following, the electronic structure of the Co-P monomers and oligomers is discussed.
Figure 3.21 shows dI /dV spectra recorded along a line over a monomer along with the STM
image of the monomer. The colored dots in the STM image mark the position where the
respective dI /dV spectrum is acquired. At the edges of the molecule a state around -700 mV is
present (red lines), whereas in the center a broad peak around -480 mV is observed (blue line).
Consequently, there are at least two occupied orbitals on different positions on the molecule in
the displayed energy range.
The shape and location of the two different monomer orbitals are visualized in dI /dV maps at
different negative biases (see fig. 3.22). At a sample bias of -0.65 V a state is visible on the four
corners of the monomer with two opposing corners showing a higher density of states than the
other two. Energetically very close, at -0.55 V, a state in the center of the molecule is observed.
This state is visible up to the Fermi energy. These findings are in good agreement with the
dI /dV spectra (fig. 3.21).
3.3 Co-porphine on Ag(111) 43
Figure 3.21: STS on a Co-P monomer. a) dI/dV spectra recorded along a line over a Co-P monomer (plottedwith offset for clarity). b) STM image of the monomer with colored dots marking the position of the respectivespectrum. At the periphery of the molecule a state is present around -700 mV and in the center another state isobserved at slightly lower energies (around -480 mV). [a) 0.15 nA, b) 2.8 × 3.2 nm2, -0.6 V, 0.15 nA]
Figure 3.22: Electronic states of the Co-P monomer and triply-fused dimer. a) to e) STM topography image(left) with simultaneously recorded dI/dV map (right) at different negative biases. a) -0.65 V, b) -0.55 V, c)-0.45 V, d) -0.35 V, e) -0.15 V. f) dI/dV curves recorded in the center of a Co-P monomer and dimer, respectively.The orbital associated with this peak is located in the center of the molecules and it is shifted closer to the Fermilevel for the dimer in comparison to the monomer. [a-e) 5.9 × 5.9 nm2, 0.2 nA]
44 3 COVALENT COUPLING OF PORPHINES
The dI /dV maps also reveal the electronic structure of a Co-P triply-fused dimer in comparison
to the monomer and to a 2H-P triply-fused dimer. At -0.65 V, both dimers exhibit no density of
states, however at -0.55 V they appear very differently. As mentioned above, the LUMO of the
2H-P dimer, two lobes on the central waist of the dimer, is shifted below the Fermi level between
-0.55 V and -0.15 V. In contrast, the Co-P dimer exhibits a state that is localized on the edges
of the molecule, very similar in shape to the state at -0.65 V on the monomer. Hence, the states
on the Co-P dimer more resemble a superposition of two Co-P monomers than a 2H-P dimer.
Indeed, at -0.45 V the two Co centers of the Co-P dimer show a higher density of states than
at -0.55 V pointing to the onset of a state localized on the Co at this bias. Towards Fermi the
density of states on the Co centers increases whereas the rest of the dimer appears dim. Thus,
both the dimer and the monomer exhibit a state localized on the Co ion but their onset energy
is different. This shift in energy between the state on both species is obvious in the dI /dV
spectra in fig. 3.22f.
For a similar system, Co-tetraphenylporphyrins (Co-TPP) on Ag(111), the HOMO exhibits two
lobes that are located on the α-pyrroles (bent upwards). This state was attributed to Co d states
interacting with the π-system of the macrocycle and it reflects the bent conformation of the
macrocycle where two opposing pyrrole rings point upwards and the other two downwards. [90]
In the case of Co-P four lobes on the macrocycle are observed for the HOMO, whereas two of
them appear slightly brighter than the other two. Since this state is not present for 2H-P it is
attributed to an interaction of the macrocycle with Co d states as well. Due to its planarity Co-P
is not expected to be distorted on the surface. Thus, the off-center spatial distribution of this
state is not triggered by a non-planar deformation of the macrocycle. However, both molecular
axes interact differently with the underlying substrate because of its three-fold symmetry. Thus,
the difference in brightness between the lobes of the HOMO can be explained by the interaction
of the macrocycle with the substrate which is different for the two molecular axes.
3.4 Dibromoporphines on Ag
In order to trigger the shape of nanostructures certain positions on the molecules can be
designed to be more reactive than others. One example is the Ullmann coupling [27, 102, 110,
123, 127, 128] where hydrogen atoms are replaced by halogen atoms. The C-halogen bond is
dissociated at far lower temperatures than the C-H bond enabling the formation of structures
with a high symmetry. Another approach is to block certain positions on the molecules by e.g.
attaching unreactive side groups (see ch. 4.2.2).
The first approach (Ullmann coupling) is employed to 2H-P molecules by synthesizing 5,15 di-
bromoporphines (trans-Br-P) and 5,10 dibromoporphines (cis-Br-P) (synthesis by Thien Ngo,
National Institute for Materials Science, Japan). STM images and structural models of both
molecules are shown in fig. 3.23a,b. Both molecules exhibit two additional round protrusions at
3.4 Dibromoporphines on Ag 45
the edge of the square-like shape of the macrocycle. For the trans-Br-P these protrusions caused
by the two Br atoms are in opposing positions on the macrocycle. Note that in fig. 3.23a the
positions of the two inner hydrogen atoms are visible on the macrocycle as well. The cis-Br-P
shows two additional protrusions on neighboring sides of the molecule in agreement with the
structural model. It is expected that upon adsorption on the Ag surface the Br atoms are split
off the macrocycle at lower temperatures than hydrogen atoms at the periphery of the molecule.
Since the radicals are most reactive at the two empty meso-positions the formation of straight
chains of coupled molecules is anticipated.
Figure 3.23: Three different species observed upon deposition of Br-porphines onto Ag(111) held at ≈ 180 K. a)Trans-Dibromoporphine with structural model, Br indicated in purple, b) Cis-Dibromoporphine with structuralmodel, c) 2H-P contaminant or debrominated porphine. [2.4 × 2.4 nm2, a,c) -0.55 V 0.08 nA; b) -0.8 V, 0.1 nA]
In the following, both molecules are compared for similar deposition temperatures on the Ag(111)
surface (see fig. 3.24). In order to image the unreacted molecule, trans-Br-P is deposited onto
Ag(111) held between 170 to 190 K (Tcru = 520 K, td = 5 min). This preparation results in a
sub-ML coverage of molecules arranged in islands or small agglomerates and single molecules
(see fig. 3.24a). Outside of the islands unreacted molecules (with both Br atoms attached to
the macrocycle) are observed to arrange in small agglomerates or as individual units. They
are identified by the two opposing additional protrusions on the macrocycle (marked by purple
circle in fig. 3.24a2). However, some of the molecules exhibit only one additional protrusion on
the macrocycle (marked by light blue circle) and others exhibit an appearance similar to 2H-P
(marked by green circle and depicted in fig. 3.23c). Within the islands these three different
species are observed as well along with small protrusions between the molecules (marked by
black circle). The small protrusions show no spectral features and because no other contami-
nants are expected from the synthesis they are attributed to detached Br atoms. Thus, some
molecules already debrominate on the surface held between 170 and 190 K.
46 3 COVALENT COUPLING OF PORPHINES
Since 2H-P do not arrange in islands on Ag(111) the Br atoms are assumed to interact attrac-
tively with the hydrogen atoms at the periphery of the molecules. Moreover, the detached Br
atoms stabilize the islands in a similar way as described e.g. in ref. [129].
Figure 3.24: Trans- and cis-dibromoporphines on Ag(111) deposited at different substrate temperatures TS . Foreach TS an overview and a high resolution image are shown. At lower temperatures most of the molecules areunreacted (marked by purple circle), around RT they are nearly fully debrominated and form Ag-coordinatedchains and above 570 K they covalently couple (one debromination, two debrominations, Ag-coordination andcovalent coupling marked by light blue, green, dark blue and red circles, respectively). The Br atoms stay on thesurface until TS = 750 K (marked by black circles). [a) -0.8 V, 0.08 nA; b1,2) -0.6 V, 0.08 nA; b3) -0.8 V, 0.13 nA;b4) -0.1 V, 0.2 nA; b5) -0.7 V, 0.12 nA; c1) -0.5 V, 0.2 nA; c2) -0.2 V, 0.5 nA; c3) -0.7 V, 0.13 nA; c4) -0.3 V, 0.13 nA;d1) -0.8 V, 0.08 nA; d2) -0.2 V, 0.08 nA; d3) -0.6 V, 0.15 nA; d4) -0.6 V, 0.11 nA; d5) -0.6 V, 0.15 nA]
After annealing to or depositing at TS = 240 to 260 K most of the trans-Br-P are arranged
in islands and a few in smaller agglomerates of only a few molecules (see fig. 3.24b1,2). For
3.4 Dibromoporphines on Ag 47
the trans-Br-P most of the molecules are unreacted. In contrast, the cis-Br-P start to couple
at these temperatures (fig. 3.24b3-5). The molecules are arranged in extended islands and in
smaller islands of several molecules. Some of the molecules, mainly within the smaller islands,
are connected via a protrusion at their meso positions (marked by dark blue circle in fig. 3.24b4
and in fig. 3.25). The connection only appears as a protrusion at negative and small positive
biases. Since the center-to-center distance is smaller than between two dibromoporphines and
larger than in the covalent dimer, a coupling involving a Ag atom is assumed. In fig. 3.25 Ag-
coordinated chains are depicted without (a) and with (b) Hyper-Chem models superimposed.
However, within the extended islands most of the molecules are unreacted or lost only one Br
atom. Moreover, most of the Ag-coordinated cis-Br-P only lost one Br atom as indicated by one
remaining protrusion on the macrocycle.
While organo-metallic coordination is commonly observed on Cu, [130–133] a few examples are
reported for Ag surfaces as well. [27,123,129,134,135] In contrast, for 2H-P no Ag-coordination
is observed upon annealing. At a high coverage the lowest annealing temperature required to
form a few dimers is 480 K where only covalent coupling is found but no Ag-coordination.
Figure 3.25: Organo-metallic coupling of debrominated porphines with Ag atoms. STM image without (a) andwith (b) structural models of Ag-coordinated chains of debrominated trans-Br-P. [3.4 × 5.2 nm2, -0.2 V, 0.5 nA]
Only upon annealing at higher temperatures metal-coordinated chains are formed by the trans-
Br-P as well. In fig. 3.24c1,2 the surface is imaged after annealing to 320 K. Within the islands
of molecules straight chains are observed where the porphines are connected via opposing meso
positions (marked by dark blue circle in fig. 3.24c2). These chains are very limited in length,
between two and five porphine units, and they are stabilized as islands by the Br atoms arranged
between the chains. Furthermore, there are many molecules within the islands that are not or
only partially debrominated. For the same annealing temperature (320 K) the appearance of the
cis-Br-P is very different. Due to the Br atoms being positioned at neighboring meso positions
of the molecule, no straight Ag-coordinated chains are formed but a disordered network. In con-
trast to the trans-Br-P, chains of more than ten porphine units are observed and all molecules
are debrominated. Only a few molecules are not Ag-coordinated.
The stability of the Ag-coordinated chains is tested for the cis-Br-P by lateral manipulation.
The tip is brought very close to the surface by lowering the applied voltage to 0.008 V and the
tunneling current is set to 2 nA. Then, the tip positioned over a Ag-coordinated chain is moved
48 3 COVALENT COUPLING OF PORPHINES
(indicated by arrow in fig. 3.26a) and the whole chain moves without breaking the Ag coordina-
tion (see fig. 3.26b).
Figure 3.26: Lateral manipulation on one molecule of a Ag-coordinated chain leads to movement of the wholechain (outline of the organo-metallic chain marked in blue). a) Before manipulation, the movement of the tip isindicated by green arrow. b) After manipulation. The additional protrusion is probably dropped by the tip. [5× 5 nm2, -0.5 V, 0.13 nA]
An increase of the annealing time from 5 to 60 min for the trans-Br-P does not lead to longer
Ag-coordinated chains, but to an increased amount of contaminants on top of the islands.
In order to convert Ag-coordinated networks into covalent networks the molecules are annealed
at 570 K (see fig. 3.24d). Indeed, for both molecules covalent coupling is observed (marked by
red circle), nevertheless for the trans-Br-P the majority of the molecules is either arranged in
islands of debrominated and not-coordinated molecules or debrominted and singly distributed
over the surface. Only a small percentage of molecules is covalently coupled in dimers or trimers.
On the other hand, for the cis-Br-P a higher percentage of molecules is covalently coupled.
Figure 3.27: Annealing at higher temperatures: a) STM image of trans-Br-P on Ag(111) after annealing at620 K. The covalent structures lack order and extended length. b) Cis-Br-P on Ag(111) after annealing at 750 K:Disordered extended covalent networks. [47.6 × 20.2 nm2, a) 1.2 V, 0.03 nA; b) -0.7 V, 0.1 nA]
Since for both molecules no extended covalent chains or networks are obtained, the anneal-
ing temperature is further increased. Figure 3.27a shows trans-Br-P after annealing at 620 K.
Despite the majority of the molecules being covalently coupled, no regular structures can be
3.4 Dibromoporphines on Ag 49
observed and the chains are still rather limited in length. The presence of contaminants on the
surface inhibited the resolution of binding motifs.
More extended covalent networks are observed for cis-Br-P after annealing to 750 K (fig 3.27b)
and no Br atoms are resolved. The covalent structures resemble the shape of the Ag-coordinated
chains and they are extended over several 100 A. The bright spots in the center of some por-
phines are presumably Ag atoms incorporated into the macrocycle (see ch. 3.1.1).
As the deposition onto a heated sample results in more efficient covalent coupling for the 2H-P,
cis-Br-P are deposited onto Ag(111) held at 570 K for 10 min. Very similar to the preparation of
annealing the sample at this temperature for 10 min islands of single, debrominated molecules
are present as well as smaller agglomerates of covalently coupled molecules (see fig. 3.28a,b).
However, an increase of the deposition time onto the heated subtrate to 45 min leads to a higher
surface coverage and a disordered arrangement of covalently coupled molecules, Br atoms and
debrominated porphines (fig. 3.28c). Presumably, some porphines couple via Ag atoms (marked
by blue circle in fig. 3.28c).
Figure 3.28: Deposition onto the heated sample: a,b) STM images of the surface after deposition of cis-Br-Ponto Ag(111) held at 570 K for 10 min. Islands of debrominated molecules and covalent coupling coexist. c)Prolongation of the deposition time to 45 min results in a high coverage of debrominated and mostly covalentlycoupled porphines. [a) 23.7 × 23.7 nm2, -1 V, 0.1 nA; b) 15.8 × 40.6 nm2, -0.7 V, 0.09 nA; c) 9.9 × 7.7 nm2, -0.9 V,0.06 nA]
The substrate geometry seems to play a minor role as shown in fig. 3.29. Cis-Br-P are deposited
onto the Ag(100) surface and annealed at 370 K. The Ag-coordinated structures resemble the
ones on Ag(111) obtained by annealing at 320 K.
In order to clarify if the central hydrogen atoms are detached, voltage pulses that induce tau-
tomerization are applied to the center of the molecules. In fig. 3.30a a voltage pulse of -1.5 V is
exerted on the edge of a singly debrominated Br-P on Ag(100) (marked by green dot). Since
the symmetry of the molecule is broken by the Br atom, the change in appearance from the top
to the bottom panel can only be achieved by tautomerization and a small lateral movement of
the molecule. The jump in the measured current is shown between the two STM images. In
50 3 COVALENT COUPLING OF PORPHINES
Figure 3.29: STM images of cis-Br-P on Ag(100) after annealing at 370 K. The debrominated porphines areconnected via Ag atoms, in a similar way as on Ag(111). [a) 52.6 × 39.6 nm2, -0.6 V, 0.17 nA; b) 10.7 × 10.7 nm2,-0.4 V, 0.17 nA]
fig. 3.30b a voltage pulse of 2 V is exerted on the bottom debrominated monomer (marked by
green dot) which causes tautomerization of both monomers in the center of the image (marked
by green arrows). Finally, in fig. 3.30c dI /dV spectra in the range from -1 to 1.5 V are recorded
in close proximity of the Ag-coordinated chain in the center of the image. The green arrow indi-
cates that one of the Ag-coordinated porphines tautomerizes. Thus, the three different species
- the partially reacted, the debrominated and the Ag-coordinated porphines - do not lose their
inner hydrogens upon adsorption and annealing to 320 K.
Figure 3.30: Tautomerization of the two hydrogen atoms in the center of the macrocycle on different species. a)A switch of the inner hydrogens of a singly debrominated Br-P on Ag(100) is induced by a voltage pulse of -1.5 Vat the position of the green dot. b) Two doubly debrominated porphines tautomerize after a voltage pulse of 2 V(position of inner hydrogen indicated by green arrow for upper molecule). c) The green arrow shows a switchof the hydrogen in a Ag-coordinated porphine after recording dI/dV spectra close by. [2.6 × 2.6 nm2, a) -0.7 V,0.1 nA; b) -0.2 V, 0.5 nA; c) 0.1 V, 0.3 nA]
The above findings invoke the question of how the covalent coupling reaction takes place. The
3.4 Dibromoporphines on Ag 51
comparison of the behavior of both molecules at the same temperatures points to a higher reac-
tivity of the cis-Br-P, i.e. that these molecules are fully debrominated at a lower temperature
than the trans-Br-P (namely after annealing at 320 K for the same time as for trans-Br-P)
and that the cis-Br-P covalently couple more efficiently at 570 K. However, the covalent struc-
tures exhibit a considerably different shape in comparison to the Ag-coordinated chains which
are straight for the trans-Br-P. This behavior is observed for other molecules that form pro-
topolymers on Ag as well with the tentative explanation that the molecules can react in several
different ways giving rise to disordered structures. [128,135] The same is true for the Br-P since
at an annealing temperature of 570 K also dehydrogenation takes place increasing the number
of possible coupling motifs. Thus, future experiments could aim for an intermediate annealing
temperature, at which the Ag-C bonds are broken but no dehydrogenation occurs.
Furthermore, it is not clear why closely arranged debrominated porphines are observed after de-
position on the sample held at 570 K for 10 min. The adsorption on the heated surface obviously
leads to debromination but not necessarily to covalent coupling. After only 10 min of deposition
the coverage might be too low for an efficient coupling. Although at the imaging temperature
of 6 K the debrominated molecules are arranged in dense-packed islands they might be more
separated at elevated temperatures and only arrange in islands during cooling. In line with this
explanation is the observation that at higher coverages (deposition time of 45 min) the majority
of all molecules is coupled (either covalently or via Ag atoms).
Figure 3.31 shows that the three different species - unreacted trans-Br-P, debrominated por-
phine and Ag-coordinated porphine - exhibit pronounced differences in the dI /dV spectra in
comparison to the featureless spectrum of the 2H-P. In the occupied range no peak is observed
up to -1000 mV and in the unoccupied range all three species show a broad peak with a shoul-
der between 500 and 1000 mV. For the brominated porphine the main peak is at slightly lower
energies than for the other two species. Thus, the unreacted and the debrominated species seem
to be chemically different as already assumed above.
Finally, dI /dV maps acquired on covalently coupled Br-porphine dimers exhibit the same two-
lobe state below the Fermi level as the 2H-P. As shown in fig. 3.32 the two protrusions on the
waist of a triply fused dimer are visible at a sample bias of -0.35 V and -0.45 V (bottom right
corner of the image) confirming the formation of the same molecule as for the 2H-P.
Moreover, a similar state is observed on a triply fused trimer. In the same bias range as for the
dimer two protrusions are present on the trimer (upper left part), whereas one of them exhibits
a higher apparent height than the other and they are both rather elongated in comparison to
the dimer. As evident in fig. 3.32c the two lobes only appear at triply fused connections but not
for the third binding motif.
52 3 COVALENT COUPLING OF PORPHINES
Figure 3.31: STS on different Br-porphine species: dI/dV spectra on an unreacted trans-Br-P, a debrominatedporphine and a Ag-coordinated porphine. The three species show only minor differences. [0.3 nA, 0.5 nA, 0.3 nA]
Figure 3.32: STM topography images (top) with simultaneously recorded dI/dV map (bottom) on covalentlycoupled Br-porphines at -0.35 and -0.45 V. The dimer (bottom right) shows a state that is also observed oncovalently coupled 2H-P and the triply-fused trimer (top left and in c) shows this two-lobed state as well. [a,b)5.7 × 4.3 nm2; c) 4.5 × 4.3 nm2; a) -0.35 V, 0.2 nA; b) -0.45 V, 0.2 nA; c) -0.45 V, 0.2 nA]
3.5 Summary
Porphines are promising candidates for building blocks in covalent nanostructures formed on
metal surfaces under UHV conditions. The unsubstituted 2H-P is shown to undergo thermally-
induced and surface-assisted dehydrogenation reactions on Ag surfaces resulting in the formation
of covalent bonds. Two approaches are employed, whereas the first, which involves annealing
a ML of 2H-P on Ag(111), is less efficient because the reaction is limited by the desorption of
molecules. In order to counteract the desorption, in the second approach 2H-P are deposited
onto a heated substrate for a deposition time that is longer than required to deposit one ML.
3.5 Summary 53
Employing the second approach the average oligomer length is drastically increased and nearly
100 % of all molecules are bound in oligomers (cf. first three rows in tab. 4). Thus, the coverage
on the surface during the reaction has to be high to achieve an efficient coupling, accordingly, less
coupling takes place at low surface coverages. The coupling efficiencies of the different systems
discussed above are summarized in tab. 4.
For both approaches three different binding motifs are observed with the first one involving
three C-C bonds and motif 2 and 3 only two C-C bonds. The triply-fused first binding motif
which is also synthesized in solution [93–95] is the most abundant for all substrate temperatures
investigated.
Spectroscopic measurements reveal that the LUMO is shifted below the Fermi level for the
triply-fused dimer and moreover, the band gap is reduced in comparison to the monomer, a
feature reported for a range of porphyrin tapes in solution. [93,94,96]
On a Ag surface with a different geometry (Ag(100)) the same coupling reactions are observed,
however, due to a stronger molecule-substrate interaction the diffusion is reduced in comparison
to the Ag(111) surface and higher temperatures are required to achieve the same amount of
molecules bound in oligomers (see tab. 4). Similar to the Ag(111) surface the triple C-C bond
is the preferred binding motif.
The influence of a metal center on the coupling reaction is studied by depositing Co-P onto
the Ag(111) surface. The desorption is reduced in comparison to 2H-P and consequently higher
substrate temperatures are required to induce the coupling reactions which yield only two dif-
ferent binding motifs, namely the first and the third, with a clear preference for the third one.
Therefore, the presence of the metal ion in the center of the molecule changes the reactivity of
the different positions at the periphery of the molecule.
For the Co-P the influence of the annealing time on the reaction is studied. It is observed that
annealing at a lower temperature for a longer time leads to the same reaction outcome (percent-
age of nonmonomers and average oligomer length) as annealing at a higher temperature for a
shorter time (see tab. 4).
Furthermore, it is shown that 2H-P oligomers can be metalated with Co, hence the shape of the
oligomers can be modified since 2H-P and Co-P exhibit different preferred binding motifs.
At last, aiming for regularly shaped porphine oligomers two hydrogen atoms at meso positions
are substituted by Br atoms. As reported for many similar cases, debromination and partial
Ag-coordination takes place upon adsorption on Ag held below RT. Annealing to higher tem-
peratures leads first to a complete Ag coordination and at 570 K covalent coupling is observed.
However, the coupling is not efficient and the adsorbed Br determines the arrangement of most
of the molecules. Only after annealing at 750 K all molecules are coupled and no Br atoms are
observed. Despite the partial order of the Ag-coordinated chains, the covalent network shows
no order.
One explanation for this behavior is that at the annealing temperature of 570 K also dehy-
54 3 COVALENT COUPLING OF PORPHINES
Molecule Surface TS (K) Deposition/annealing time? (min) Nonmonomers (%)
2H-P Ag(111) 530 90 51± 22H-P Ag(111) 570 90 80± 32H-P Ag(111) 610 90 97± 32H-P Ag(100) 620 40 86± 5Co-P Ag(111) 610 20 22± 3Co-P Ag(111) 610 140 82± 6Co-P Ag(111) 630 10 80± 5
Table 4: Comparison of the covalent coupling reactions of 2H-P and Co-P on Ag(111) and Ag(100). Theresulting percentage of nonmonomers is given for the different systems discussed above. ?For 2H-P/Ag(111) thetime corresponds to the deposition time onto the heated substrate, for all other cases the time refers to theannealing time.
drogenation reactions occur, increasing the number of possible binding motifs. Thus, future
experiments could try to aim for more ordered chains by annealing at a temperature at which
the Br is split off but the hydrogens do not react. Another option is to employ a substrate that
does not supply atoms for the formation of metal-organic chains.
Overall, the homocoupling of porphines on Ag is a cleaner approach than Ullmann coupling
since no reaction byproducts remain on the surface and furthermore, the reaction is more effi-
cient under the conditions mentioned above.
Possible future experiments comprise to study the influence of the deposition time for the cou-
pling of 2H-P on Ag(111), the influence of the coverage on the coupling of Co-P on Ag(111),
metalation of oligomers with different metals in order to study the electronic and magnetic effects
(see e.g. [85]) and the interaction of metalated oligomers with small gas molecules. Furthermore,
the conductance through oligomers could be measured by attaching one end of the oligomer at
the tip and then by lifting it from the surface creating a single-molecule junction (see e.g. [136]).
55
4 Ring-closing reactions on phenyl-substituted porphyrins
Selectivity of chemical reactions is a major goal in catalysis in order to maximize the efficiency
and to avoid spurious byproducts. [137–139] In industrial large scale production [140–143] as
well as in biological processes [144] the most prevalent property that generates selectivity is
structural symmetry of the precursors. Although this concept is widespread in homogeneous
catalysis [145,146] it still requires more understanding in heterogeneous catalysis. [138,147,148]
In on-surface chemical reactions selectivity can be triggered by surface reactivity [117] and
structure, [131] as well as by the molecular geometry. [83, 86, 149, 150] In the following, the
latter parameter is shown to be decisive for the distribution of reaction products in an on-
surface reaction.
The free-base tetraphenylporphyrin (2H-TPP) undergoes intramolecular cyclodehydrogenation
or ring-closing reactions upon annealing on the Ag(111) surface resulting in the formation of
planar porphyrin derivatives. [108, 151] The reaction is catalyzed by the substrate and four
reaction products are identified by STM whereas one of the products is clearly favored over the
others. Due to the observation of reaction intermediates the reaction is assumed to take place
step-wise. Thus, the ground state energies of the intermediates are calculated by DFT which
point to an influence of the symmetry of the core of the molecule on the reaction outcome.
Indeed, two molecules with a different geometry in the core, namely Ru-TPP and Co-TPP,
exhibit a more uniform distribution of the same four reaction products.
As a next step, the 5,15 Diphenylporphyrin is annealed on the Ag(111) surface. On the one hand,
the two phenyl rings are expected to react with the macrocycle similar to 2H-TPP, on the other
hand the hydrogenated meso positions are expected to dehydrogenate at elevated temperatures
and covalently couple with neighboring molecules, as observed for 2H-P (see ch. 3.1.1). These
two processes are observed to take place at different substrate temperatures. The two ring-
closing reactions occur at lower temperatures, yielding mainly the product proposed by DFT,
and these planar molecules covalently couple at higher temperatures.
4.1 Tetraphenylporphyrins on Ag(111)
Room temperature deposition of TPPs onto Ag(111) results in the formation of extended
dense-packed islands of molecules. This behavior is observed for free-base TPP [107, 152] as
well as for several metal-TPPs. [89, 106–108] The attractive interaction between the molecules
is established by the phenyl rings which are tilted towards the surface (see fig. 4.1a). Within
the islands two phenyl rings of neighboring molecules are oriented such that one phenyl ring is
perpendicular to the other one. In this configuration (T-shape) the two phenyl rings interact
attractively via van der Waals interaction. [107, 152] Figure 4.1b shows an island of 2H-TPP
after deposition at RT (Tcru = 600 K, td = 4 min, STM image acquired by Knud Seufert) where
56 4 RING-CLOSING REACTIONS ON PHENYL-SUBSTITUTED PORPHYRINS
the outline of one molecule is marked in green.
Figure 4.1: 2H-TPP on Ag(111). a) STM image and structural model. The four phenyl rings (numbered) aretilted and thus appear higher. The outline of the molecule is marked in green. b) Island formation after RTdeposition. The molecules interact attractively via their tilted phenyl rings. c) Planar porphyrin derivatives afterannealing at 560 K for 10 minutes. Adapted from [153]. [a) 2.1 × 2.1 nm2, -1 V, 0.2 nA; b,c) 15.7 × 10.8 nm2; b)-0.8 V, 0.2 nA; c) -0.3 V, 0.1 nA]
Annealing 2H-TPP on Ag(111) between 530 and 620 K induces intramolecular dehydrogenation
and ring-closing reactions as shown in refs. [108, 151]. Figure 4.1c shows the surface after an-
nealing at 560 K for 10 min. The molecules are not ordered, exhibit a larger footprint on the
surface and their apparent height is more uniform than before annealing. This conformational
change was attributed to several intramolecular ring-closing reactions which result in planar
porphyrin derivatives (PPD). Indeed, temperature-programmed desorption (TPD) spectra on
a 2H-TPP multilayer show hydrogen evolution in the expected temperature range (TPD mea-
surements were supervised by David A. Duncan and Francesco Allegretti). Figure 4.2 shows
a broad peak in the hydrogen (H2) spectrum (black line) with an onset temperature of 500 K
which extends to above 700 K. As a comparison, the TPD spectrum with m/z (mass-to-charge
ratio) 59, corresponding to the desorption of 2H-TPP (green line), exhibits a large peak at 470 K
indicating the multilayer desorption and a shoulder in the large peak around 550 K where some
2H-TPP desorb during the ring-closing reactions since the PPDs have a larger footprint on the
surface than 2H-TPP. The m/z 59 corresponds to 2H-TPP desorption because it is the ratio for
a fragment of the unreacted 2H-TPP.
The intramolecular ring-closing reactions lead to the formation of four different PPDs (labeled
as A to D in fig. 4.3, the four species observed by STM are labeled with letters and the structural
models proposed by DFT (see below) are numbered). At the four phenyl rings dehydrogenation
reactions take place and at the periphery of the macrocycle as well followed by the formation of a
C-C bond between a phenyl ring and the macrocycle. Overall, there are sixteen possibilities how
the phenyl rings can react with the macrocycle. However, there are only four different reaction
products (structural models in fig. 4.3, the numbers correspond to the numbers in ref. [153]) and
4.1 Tetraphenylporphyrins on Ag(111) 57
Figure 4.2: Temperature programmed desorption spectra recorded on a multilayer of 2H-TPP on Ag(111) show-ing dehydrogenation (black line) and molecular desorption (green line - m/z 59, indicative of 2H-TPP desorption)at a heating rate of 0.5 Ks−1. Adapted from [153].
their tautomers. Theoretically, these four species should occur with a certain distribution cor-
responding to the number of equivalent reaction products, namely: Species 11: 12.5 %, species
12: 50 %, species 13: 25 % and species 14: 12.5 %. In contrast, the experimental observation of
the four PPDs depicted in fig. 4.3 clearly deviates from this distribution with species A being
clearly favored (86 %) over the other three (species B: 12 %, species C and D: < 3 %). The
origin of this deviation is investigated below.
Figure 4.3: Four planar porphyrin derivatives: STM image with tentative structural model. The moleculesobserved by STM are labeled by letters (A to D) and the structural models suggested by DFT are numbered (11to 14, see [153]). Occurrence of the four species: A: 86 %, B: 12 %, C: < 3 %, D: < 3 %. Adapted from [153].[2.7 × 2.7 nm2; A: -0.01 V, 0.1 nA; B: -0.8 V, 0.2 nA; C: -0.8 V, 0.2 nA; D: -0.01 V, 0.1 nA]
As the onset of the dehydrogenation peak in the TPD spectrum is at 500 K the sample is an-
nealed at a slightly higher temperature, namely 520 K for 10 min. After subsequent cooling,
about one fifth of the molecules is unreacted, an even smaller amount appears as PPDs and
the rest of the molecules has one to three reacted phenyl rings. Figure 4.4a shows an overview
58 4 RING-CLOSING REACTIONS ON PHENYL-SUBSTITUTED PORPHYRINS
STM image with superimposed outlines of the molecules. For the unreacted molecules the four
phenyl rings clearly exhibit a larger apparent height than the macrocycle because they are tilted.
In fig. 4.4a some of the molecules have only three or less phenyl rings with a larger apparent
height which means that some of the phenyl rings reacted with the macrocycle. Consequently,
due to the observation of reaction intermediates it can be assumed that the reaction takes place
step-wise. Figure 4.4b to g shows three reaction intermediates with their tentative structural
models.
Figure 4.4: Reaction intermediates which are partially flattened. a) STM image of 2H-TPP on Ag(111) afterannealing at 520 K for 10 min. For most of the molecules one or more phenyl rings reacted with the macrocycle.The outlines of the molecules are shown in black. b) Intermediate species 1 with one flat phenyl ring with c)tentative model. d) Intermediate species 2 with two flat phenyl rings with e) tentative model. f) Intermediatespecies 3 with three flat phenyl rings with g) tentative model. Adapted from [153]. [a) 10 × 9.2 nm2; b,d,f) 2.1× 2.1 nm2; 0.2 nA; a,d) -1 V; b,f) -0.5 V]
The observation of reaction intermediates motivates to examine the reaction pathway by DFT
calculations (carried out by Julian A. Lloyd). The comparison of ground state energies of dif-
ferent possible reaction intermediates gives the preferred reaction pathway. In general, the rate
of a chemical reaction depends mainly on the barrier height. Since the ring-closing reactions
described above involve very similar reactions - dehydrogenation and C-C bond formation - it
can be assumed that the barrier height is inversely proportional to the enthalpy of reaction
(Bell-Evans-Polanyi principle). [154] Consequently, the reaction which occurs with the highest
probability has the highest enthalpy of reaction, i.e. the lowest ground state energy. The cal-
culations are performed without a substrate because the reaction temperature is close to the
desorption temperature of the molecules reducing significantly the molecule-substrate interac-
tions during the reaction.
A detailed description of the reaction pathway is given in ref. [153]. In summary, the reac-
tion product with minimal ground state energy in all steps of the reaction yields species 11
(see fig. 4.3). The appearance of the majority species observed by STM, species A, is in good
agreement with the structural model of species 11. The tautomer of 11, and species 12 to 14
exhibit significantly higher ground state energies than 11. For the unreacted 2H-TPP the two
4.1 Tetraphenylporphyrins on Ag(111) 59
tautomers are degenerate, [155] however already for the first ring-closing reaction the ground
state energies of the tautomers are different. This difference increases in the course of the re-
action pathway towards 0.55 eV for species 11. Accordingly, no tautomerization is observed by
STM after voltage pulses exerted on the PPDs (cf. [23]). With no influence from the substrate
being responsible for the selectivity towards species 11 the energetic difference of the tautomers
points to an influence of the symmetry of the core of the molecule. Consequently, it is expected
that a change of this symmetry, e.g. by incorporation of a metal ion, changes the occurrence of
the reaction products.
Indeed, it is shown that Ru-TPP molecules undergo the same ring-closing reactions on the
Ag(111) surface upon annealing at slightly higher temperatures, namely 620 K (STM exper-
iments supervised by Anthoula C. Papageorgiou and Joachim Reichert). [153] Furthermore,
planar Co-porphyrin derivatives are observed on Ag(111) after annealing at 560 K. Four differ-
ent species are observed for Ru-TPP and Co-TPP and their shape is very similar to species A
to D observed for 2H-TPP molecules (see fig. 4.5 for Co-TPP).
Figure 4.5: Four planar Co-porphyrin derivatives on Ag(111) after annealing at 560 K for 10 min. They exhibitthe same shape as the species A to D formed by the free-base porphyrin. [2.7 × 2.7 nm2; -0.7 V, 0.2 nA]
The occurrence of the four planar species is plotted in a histogram in fig. 7.7 for Ru-TPP (red),
Co-TPP (yellow) and 2H-TPP (green). As anticipated above, the distribution of the four reac-
tion products is clearly different for the two metal-porphyrins in comparison to the 2H-porphyrin.
Whereas species A is clearly favored for the 2H-TPP, for both Ru-TPP and Co-TPP the four
reaction products appear in more similar amounts. Furthermore, in ch. 4.2.1 it is shown that
the 5,15 Diphenylporphyrin mainly forms the reaction intermediate proposed by the DFT cal-
culations.
These experimental findings corroborate the assumption deduced from the DFT calculations
that the symmetry of the core of the molecule influences the outcome of the ring-closing reac-
tions. By reducing the symmetry of the core (from metal-porphyrin to 2H-TPP) the selectivity
is increased.
60 4 RING-CLOSING REACTIONS ON PHENYL-SUBSTITUTED PORPHYRINS
Figure 4.6: Histogram of four planar porphyrin derivatives on Ag(111) for Ru-TPP (red), Co-TPP (yellow) and2H-TPP (green). Only for 2H-TPP one species (namely species A) is clearly favored. Error bars correspond tostandard deviation.
4.2 5,15-Diphenylporphyrins on Ag and Cu surfaces
The 5,15 Diphenylporphyrins (DPP) are expected on the one hand to exhibit a similar re-
activity at the hydrogenated meso positions as the porphine and on the other hand to become
planar on the surface by heat-induced ring-closing reactions involving the two phenyl rings. In
the following, the interplay of both processes is studied on Ag and Cu surfaces.
After RT deposition of DPP on Ag(111) (Tcru = 560 K, td = 1 min) the molecules are unreacted
and arrange in single, double and rarely broader chains. A single DPP is depicted in fig. 4.7a
with the structural model in b. The macrocycle appears with a depression in the center and
two protrusions on opposing edges which mark the positions of the central hydrogen atoms.
Two protrusions attached on opposing sides of the macrocycle correspond to the tilted phenyl
rings. Due to the tilting the C and H atoms that are the furthest away from the surface are not
positioned on the symmetry axis given by the two opposing meso positions but slightly offset.
Therefore, the two protrusions appear closer to the β than to the meso positions.
In order to understand the intermolecular interactions structural models are superimposed in
fig. 4.7d. Since the T-type interaction in 2H-TPP islands takes place between two phenyl rings
that point in different directions perpendicular to each other, this interaction is not possible for
the DPP. However, as evident in fig. 4.7d the tilted phenyl rings can interact with the planar
macrocycle of a neighboring molecule. This interaction seems to be stronger for molecules in
the same chain (marked by dark green circle) because mostly single chains are observed but it
is also strong enough between the chains to form some double and broader chains (marked by
light green circle).
4.2 5,15-Diphenylporphyrins on Ag and Cu surfaces 61
Figure 4.7: 5,15-Diphenylporphyrin on Ag(111) after RT deposition. a) High resolution STM image with b)structural model. c) Overview STM image: The molecules arrange in single or double chains. d) Double chain withstructural models overlaid. The tilted phenyl rings can interact attractively with the macrocycle of a neighboringmolecule. [a) 1.6 × 2.5 nm2, -0.04 V, 0.1 nA; c) 23.7 × 18.8 nm2, -0.6 V, 0.1 nA; d) 4.5 × 7.6 nm2, -0.05 V, 0.7 nA]
4.2.1 Ring-closing reactions on Ag and Cu
Upon annealing DPP on Ag(111) the molecules undergo a conformational change and they
are no longer arranged in chains but singly dispersed. After annealing at 520 K for 20 min a few
molecules appear different and after annealing at 580 K for 20 min all molecules reacted. Figure
4.8a and b depict the majority and minority species, respectively, with their tentative structural
models. Due to the similarity to 2H-TPP it is assumed that the same dehydrogenation and
C-C bond formation reactions take place as described above (ch. 4.1), with the only difference
that only the two phenyl rings react with the macrocycle. Thus, the two species observed after
annealing exhibit a uniform apparent height pointing to the formation of planar molecules.
In general, four different reaction products are possible for the two ring-closing reactions, since
each phenyl ring can either react with the pyrrolic (-NH) or the iminic (=N) part of the macro-
cycle. The structural models of these four products are depicted in fig. 4.9. For species a both
phenyl rings reacted with the iminic parts and for species x both phenyl rings reacted with the
pyrrolic parts. b and y are equivalent under rotation. In order to compare these structural
models to the STM data it has to be considered that the unreacted molecules have two possi-
bilities to adsorb on the surface, i.e. the molecule itself and its mirrored counterpart can be
observed. The same is true for the reacted molecules. With the two central hydrogens marking
a symmetry axis on the molecule a precise identification of the molecules in the STM images is
possible by superimposing structural models. Overall, the majority of the molecules appears as
species a and a smaller amount as b, whereas x is not observed (in 200 molecules). A detailed
statistical analysis is given below.
62 4 RING-CLOSING REACTIONS ON PHENYL-SUBSTITUTED PORPHYRINS
Figure 4.8: Ring-closing reactions on DPPs on Ag(111). a) Majority and b) minority reaction product withstructural models. The apparent height of the phenyl rings is significantly reduced pointing to a reaction withthe macrocycle resulting in a planar molecule. c) Overview STM image after annealing at 580 K for 20 min. Themolecules are not arranged in chains anymore due to the missing interaction of the tilted phenyl rings with themacrocycle. [a,b) 1.8 × 2.3 nm2; c) 19.7 × 16.2 nm2; -0.2 V, 0.15 nA]
Figure 4.9: Four possible reaction products of the two ring-closing reactions on DPP on Ag(111). a) Majorityspecies, b) and y) are equivalent under rotation, x) is not observed. Structural models obtained by Hyper-Chem.
The fact that species x is not observed after annealing DPP molecules is in good agreement with
the DFT calculations on 2H-TPP. As shown in ref. [153] the ground state energy for a porphyrin
with two phenyl rings that reacted with the macrocycle is minimal for species a. Thus, the two
ring-closing reactions of DPP on Ag(111) are an additional experimental indication that the
reaction pathway proposed by DFT describes the ring-closing reactions on 2H-TPP.
Annealing DPP molecules on a Ag(100) surface induces the same ring-closing reactions.
Similar to the case of the 2H-P, for the DPP a few planar species with a protrusion in the center
are observed after annealing on Ag(111) and Ag(100). Figure 4.10 shows the two different planar
species with a protrusion in the center on the Ag(100) surface which was annealed at 610 K for
10 min. Due to the similarity to 2H-P interacting with Ag atoms, these DPP species are also
assumed to incorporate a Ag atom from the substrate in the center of the macrocycle.
However, a change of the substrate material leads to pronounced differences of the behavior
upon annealing. On Cu(111) annealing a sub-ML of DPP at 520 K for 20 min results in singly
4.2 5,15-Diphenylporphyrins on Ag and Cu surfaces 63
Figure 4.10: Two different planar DPP species interacting with a Ag atom from the Ag(100) substrate whichwas annealed at 610 K for 10 min. [5.0 × 4.0 nm2, -0.5 V, 0.2 nA]
distributed planar DPP derivatives (see fig. 4.11c). High resolution STM images (fig. 4.11a,b)
reveal that the molecules exhibit a uniform apparent height and their shape more resembles
the planar DPP derivatives on Ag(111) than the unreacted molecules. The left molecule in
fig. 4.11a,b is identified as species a and the right one as species b. At negative sample biases
species a and b show a protrusion in the center that is more pronounced for species a. Whereas
at positive biases the center appears similar in height to the macrocycle and the reacted phenyl
rings appear higher. The protrusion in the center is attributed to a Cu atom which is incorpo-
rated into the macrocycle. Self-metalation on the Cu(111) surface was observed for 2H-P [105]
and 2H-TPP. [156] For both molecules the metalation takes place at substrate temperatures
around 420 K. Thus, it can be assumed that the metalation of DPP starts at a similar tem-
perature leading to a complete metalation after annealing at 520 K. As a comparison to the
appearance of the metalated DPP, Cu-P on Cu(111) is depicted in fig. 4.11 at negative (d) and
positive bias (e). The Cu center appears higher at negative biases as well.
Whereas all DPP molecules are planar on Cu(111) after annealing at 520 K for 20 min, the same
treatment on Ag(111) leads only to a few ring-closing reactions. Either the stronger reactivity
of the Cu surface causes the higher reaction rate at this temperature or the fact that probably
all molecules are metalated on Cu before the ring-closing reactions start might have an influence
on the reaction. As stated in ch. 4.1 the presence of a metal atom in the center of the macrocy-
cle instead of two hydrogen atoms has an impact on the distribution of the reaction products.
Consequently, a different distribution for the reaction products a and b is expected for DPP on
Ag and Cu-DPP on Cu(111) (note that a and x are equivalent for Cu-DPP). Indeed, as shown
in tab. 5, the majority species is formed for roughly 90 % of the molecules on the Ag surfaces,
however on Cu(111) only for 73 % of the molecules. Thus, these numbers give another hint that
64 4 RING-CLOSING REACTIONS ON PHENYL-SUBSTITUTED PORPHYRINS
Figure 4.11: Ring-closing reactions on DPPs on Cu(111). a) At negative sample biases the center appears higherin STM images for both planar species (left: species a, right: species b). b) At positive biases the reacted phenylrings appear higher than the rest of the molecule. c) Overview STM image: the planar DPPs do not assembleon Cu(111). d) Cu-P formed on Cu(111) by heat-induced self-metalation of 2H-P (see [105]) at negative bias ande) at positive bias. Similarly to DPP the Cu center appears higher at negative bias. [a,b) 4.8 × 2.6 nm2, c) 34.4× 24.4 nm2, d,e) 1.7 × 1.7 nm2; a) -0.7 V, 0.2 nA; b) 0.7 V, 0.2 nA; c) -0.4 V, 0.2 nA; d) -0.5 V, 0.2 nA; e) 1 V,0.08 nA]
the outcome of the described ring-closing reactions can be influenced by changing the geometry
of the core of the molecule.
Substrate Majority species a Minority species b
Ag(111) 91± 7 9± 2Ag(100) 87± 8 13± 3Cu(111) 73± 6 27± 4
Table 5: Ring-closing reactions of DPP on Ag and Cu: Occurrence of the two planar species (majority andminority species). Errors correspond to standard deviation.
4.2.2 Covalent coupling on Ag and Cu
Considering that 2H-P molecules are observed to couple covalently on Ag surfaces after an-
nealing to at least 530 K, it is expected that the two hydrogenated meso positions of the DPP
are similarly reactive. In fact, a few coupled molecules are observed on Ag(111) and Ag(100)
after annealing at 580 K and on Cu(111) as well. With this, similar structures are formed as ob-
tained with debrominated Dibromo-diphenylporphyrins on Au(111), [157] however without any
byproducts left on the surface. The amount of coupled molecules can be increased by increasing
the annealing temperature. The nature of the bonds is discussed separately for the Ag and Cu
surfaces in the following.
Figure 4.12 shows the Ag(111) surface after annealing a low coverage of DPP at 630 K for 20 min
4.2 5,15-Diphenylporphyrins on Ag and Cu surfaces 65
Figure 4.12: Covalent coupling of planar DPP derivatives on a) Ag(111) after annealing at 630 K for 20 min andb) on Ag(100) after annealing at 650 K for 20 min. [21.9 × 17.0 nm2, a) -0.5 V, 0.15 nA; b) 0.3 V, 0.2 nA]
(a) and the Ag(100) surface after annealing a high coverage of DPP at 650 K for 20 min (b).
The desorption is significantly smaller at these temperatures than for 2H-P on Ag(111), hence
annealing after the deposition of molecules is sufficient to achieve considerable coupling between
the molecules. On both surfaces monomers and oligomers are present after annealing, exhibiting
no long-range order. In order to identify the nature of the bonds, structural models are super-
imposed with the STM images (fig. 4.13). As for the 2H-P coupling, some hydrogen atoms of
neighboring molecules overlap, leaving no space for metal-coordination or van der Waals inter-
action. Thus, it is assumed that the molecules couple covalently.
The superposition of structural models with STM images of oligomers reveals a variety of bind-
ing motifs between the DPP molecules. Not all motifs can be identified and some appear only
rarely. The five most abundant motifs are depicted in fig. 4.13. Unexpectedly, the molecules do
not preferentially couple via their meso positions but in many cases β positions are involved
and also the planar phenyl rings react with macrocycles of neighboring molecules. The single
β−β bond which is not observed for 2H-P coupling is the most abundant motif on Ag(111) (see
fig. 4.13a). Motif 1 (β−β,meso−meso, β−β) and motif 2 (meso−β, β−meso) occur significantly
less often. Additionally, two motifs involving the coupling between a planar phenyl ring and the
macrocycle of another molecule are observed. The different positions of the planar phenyl rings
that can form bonds are numbered as indicated in fig. 4.13a, thus the single bond in fig. 4.13e is
referred to as phenyl2− β and the double bond in fig. 4.13f as phenyl2− β, phenyl3−meso.For both surfaces, Ag(111) and Ag(100), 73 motifs are determined each and their occurrence
is compared in tab. 6. Whereas on Ag(111) (after annealing at 630 K for 20 min) the preferred
binding motif is the single β − β bond, on Ag(100) (after annealing at 650 K for 20 min) several
motifs appear in roughly similar amounts. It cannot be excluded that the temperature plays
an important role for the distribution of the binding motifs since there is a difference of 20 K in
the annealing temperature of both samples. However, at a lower annealing temperature, namely
610 K, no preference for a certain motif is found on Ag(100) either. Furthermore, the coverage
66 4 RING-CLOSING REACTIONS ON PHENYL-SUBSTITUTED PORPHYRINS
Figure 4.13: Covalent binding motifs of DPP on Ag. a) β−β, b,c) β−β,meso−meso, β−β, d) meso−β, β−meso,e) phenyl2− β, f) phenyl2− β, phenyl3−meso. [3.6 × 3.6 nm2, 0.5 V, 0.15 nA]
during the reaction might play a role since it is different on both samples and most importantly,
the surface geometry and thus the adsorption site of the molecules is different on both surfaces.
Binding motif Anneal at 630 K Anneal at 650 Kon Ag(111) on Ag(100)
β − β 37 9β − β,meso−meso, β − β (motif 1) 16 18
meso− β, β −meso (motif 3) 9 12phenyl2− β 6 11
phenyl2− β, phenyl3−meso 5 23
Table 6: Occurrence of different binding motifs of DPP on Ag(111) and Ag(100) in numbers of counted motifs(in total 73 for each substrate). Motifs are determined by superimposing structural models.
Another observation during the identification of the binding motifs is that for the motifs β − βand meso− β, β −meso (2. motif) only molecules of the same orientation couple, i.e. in these
motifs the molecules only couple to other molecules that adsorbed in the same way on the surface
but not with their mirrored counterparts. For the other motifs also different molecules couple.
The minority species appears in nearly all binding motifs, either bound to another minority
species or to a majority species.
4.2 5,15-Diphenylporphyrins on Ag and Cu surfaces 67
In contrast, the situation is very different on the Cu(111) surface. Firstly, the surface itself is
more reactive and for many organic molecules organo-metallic coupling is observed at elevated
temperatures. Secondly, the DPPs on Cu are metalated with Cu atoms from the substrate at the
annealing temperatures required for covalent coupling. Thus, considering the altered occurrence
of binding motifs for the metal-porphines (Co-P) in comparison to the 2H-porphine, a different
reactivity of the periphery is expected for the planar Cu-DPP as well.
As shown in fig. 4.14 some Cu-DPP couple upon annealing at 570 K for 20 min. The percentage
of coupled molecules is increased by annealing at a higher temperature, namely at 620 K (see
fig. 4.14). The nature of the bonds and its motifs are again determined by superimposing struc-
tural models with the STM images (fig. 4.15).
Figure 4.14: Coupling of DPP molecules on Cu(111) after a) annealing at 570 K for 20 min and b) at 620 K for20 min. [23.7 × 20.0 nm2; a) -0.6 V, 0.2 nA; b) -0.8 V, 0.15 nA]
The distances between the outer hydrogen atoms of neighboring models in fig. 4.15 point to the
occurrence of Cu-coordination between molecules in some cases and covalent coupling in other
cases. In fig. 4.15a the hydrogen atoms of the two neighboring molecules do not overlap and two
protrusions with a greater apparent height than the molecule are present between the molecules.
Since the formation of Cu-mediated bonds is frequently observed on Cu surfaces, a coupling via
two Cu atoms is assumed. In contrast, in fig. 4.15b three Cu atoms are arranged between the
molecule on the left and the central one.
However, the models of the central and the right molecule in fig. 4.15b overlap pointing to the
formation of a covalent bond. Most of the observed covalent coupling motifs involve a single
bond, either between two β positions (fig. 4.15c) or between a planar phenyl ring and a β position
(fig. 4.15b,d,e). Thus, the coupling is indeed different from the Ag surface where also covalent
motifs involving two or three C-C bonds are observed. In total, covalent and Cu-coordinated
coupling occur in approximately similar amounts at this temperature (570 K).
68 4 RING-CLOSING REACTIONS ON PHENYL-SUBSTITUTED PORPHYRINS
Figure 4.15: Coupling of DPP on Cu(111) upon annealing at 570 K for 20 min: STM images of oligomers withsuperimposed structural models. a) Cu-coordination involving two Cu atoms, b) Cu-coordination involving threeCu atoms and covalent coupling (phenyl3− β), c) covalent coupling (β − β), d,e) less obvious if Cu-coordinationor covalent coupling. Some molecules seem to be metal-free again, e.g. in a, and some DPPs are clearly metalatedwith Cu, e.g. in c. [3.7 × 4.4 nm2; a,b,d) 0.1 V, 0.1 nA; c) -0.2 V, 0.12 nA; e) -0.6 V, 0.2 nA]
4.2.3 Electronic structure
The electronic states close to the Fermi level on planar DPPs are probed by dI /dV mapping.
In fig. 4.16 two monomers and two dimers are shown on the Ag(100) surface.
Figure 4.16: STM topography image (left) and dI/dV map (right) on DPP on Ag(100). The dimer in the topleft is singly-fused and the one in the bottom right is triply-fused. Different sample biases: a) -0.3 V, b) -0.2 V, c)-0.1 V, d) 0.1 V, e) 0.2 V, f) 0.3 V. [a-e) 5.9 × 5.9 nm2, f) 5.3 × 5.9 nm2; 0.2 nA]
The dimer in the top left of the STM image is singly-fused and the one in the bottom right
4.3 Summary 69
is triply-fused. At -0.3 and -0.2 V the monomers exhibit a clear state that is located on the
edges of the molecule with two circular protrusions and two elongated ones. Slightly closer to
the Fermi level, the singly-fused dimer shows a state which is the superposition of the state on
the monomer for the two molecules of the dimer. The fact that the monomers appear dim at
-0.1 V whereas the singly-fused dimer shows a pronounced state, indicates that the occupied
state observed on the monomer and the dimer is shifted closer to the Fermi level for the dimer.
The triply-fused dimer shows a state at -0.2 V which is slightly different from the other dimer
and the monomers since it only involves circular protrusions.
At positive sample biases both dimers exhibit a state on the waist of the molecule, at 0.1 V for
the singly-fused dimer and at 0.2 V for the triply-fused dimer.
4.3 Summary
In summary, the symmetry of the core of a porphyrin molecule is shown to be decisive for
the outcome of an on-surface chemical reaction. Upon annealing on the Ag(111) surface 2H-
TPP molecules undergo several ring-closing reactions which result in planar molecules. The
dehydrogenation reactions during the ring-closing are monitored by recording the hydrogen
evolution temperature-dependent (TPD). All four possible reaction products are resolved by
STM whereas one product is clearly favored over the others.
Since reaction intermediates are observed at lower temperatures it is concluded that the reaction
takes place step-wise. The ground state energies of several reaction intermediates are calculated
by DFT suggesting the minimal energy reaction pathway. Within this pathway the selectivity
towards the final product is determined by the symmetry of the core of the molecule. In order
to test this hypothesis, two molecules with a higher symmetry in the core are annealed on the
same surface, namely Ru-TPP and Co-TPP (four-fold symmetric). For both metal-TPPs the
reaction is less selective, i.e. the distribution of the four reaction products is more uniform than
for the 2H-TPP. Consequently, these experimental results support the conclusion of the DFT
calculations that a decrease of the symmetry of the core of the molecule (from metal-TPP to
2H-TPP) increases the selectivity of the reaction.
In contrast, for the DPP molecules three different processes occur upon annealing: First, the
two phenyl rings react with the macrocycle in a similar way as the 2H-TPP, on both Ag and Cu
surfaces. Second, in a similar temperature range the molecules self-metalate on Cu with atoms
from the substrate, as it is observed for 2H-P and 2H-TPP. [105, 158] At last, the planar DPP
derivatives couple covalently at elevated annealing temperatures, comparable to the covalent
coupling of 2H-P on Ag (see ch. 3.1.1). On the Cu surface, both Cu coordinated and covalent
bonds between planar DPPs coexist. On Ag however, more binding motifs than for 2H-P on
Ag are observed and the occurrence of the binding motifs is also changed. Furthermore, more
pronounced differences between the coupling on the Ag(111) and Ag(100) surfaces are observed
70 4 RING-CLOSING REACTIONS ON PHENYL-SUBSTITUTED PORPHYRINS
than for 2H-P.
In order to further substantiate the proposed mechanism of the symmetry of the molecule being
decisive for the reaction outcome, more extensive DFT calculations including metal-TPPs need
to be carried out or more experimental data on different metal-TPPs needs to be acquired.
For the DPP molecules, non-contact atomic force microscopy (AFM) measurements could help
to reveal the topographic structure of the differently coupled molecules, since Hyper-Chem
calculations suggest substantial bending for some of the covalent motifs.
71
5 Adsorption and coupling of iron-phthalocyanine on Cu(111)
Similar to porphyrins, phthalocyanines adsorbed on metal surfaces are studied intensively
with the goal to realize electronic and optoelectronic devices based on (metal-)organic molecules.
[22, 40, 159] Due to their versatile properties phthalocyanines are employed in e.g. gas sensors,
[160] solar cells, [161] and field effect transistors. [162] The ability to incorporate different
metal ions in their macrocycle makes phthalocyanines promising candidates for spin-dependent
electronics as well. [32, 33]
For the application in devices it is necessary to understand the interaction of the molecules
with the underlying substrate, as e.g. the conductance through a molecule and its magnetic
properties can vary with the adsorption site. [163,164]
Upon adsorption of several metal-phthalocyanines (MPc) on different metal surfaces a change of
the symmetry of the molecule is observed in STM images. In gas phase MPcs exhibit a four-fold
symmetry, which is preserved on the surface for different systems as CoPc/Cu(100) [125] and
Fe-,Co-,Ni-,CuPc/Ag(100). [165] However, for other systems the symmetry of the molecules is
reduced to two-fold in the STM images with one molecular axis appearing higher than the other
one, e.g. for CoPc and FePc/Cu(111), [125,126,163] FePc/Cu(100), [166] CuPc/Cu(111) [125,
167] and SnPc/Ag(111). [168] The origin of the symmetry reduction is still not fully understood
and was attributed to either being a geometric distortion of the molecules on the surface,
[126,166] an electronic effect caused by the interaction of the molecule with the surface [163,169]
or a combination of both. [125]
Here, the system FePc/Cu(111) is studied with complementary methods pointing to an electronic
effect caused by an asymmetric charge transfer and probably a slight geometric contribution due
to bending of the molecule.
In the second part, a polymerization reaction of FePc/Cu(111) which was first observed by
Manandhar et al. [170] is described. STM and XPS data point to a partial decomposition of the
molecules upon annealing.
5.1 Symmetry reduction
Room temperature deposition of small amounts of FePc onto the Cu(111) surface results in a
sub-ML of isolated molecules (Tcru = 680 K, td = 30 min). The coverage-dependent arrangement
and island formation of FePc on Cu(111) is discussed in ref. [171] and here only coverages below
0.4 ML are regarded. The appearance of FePc in STM images is cross-shaped with a protrusion
in the center induced by the Fe ion (fig. 5.1a with structural model in b).
The adsorption site of FePc on the Cu(111) lattice can be determined by adsorbing CO on the
surface (dose in-situ for 1 min, p: 1.0 · 10−7 mbar). With CO always occupying on-top positions
72 5 ADSORPTION AND COUPLING OF IRON-PHTHALOCYANINE ON CU(111)
Figure 5.1: Room temperature deposition of FePc on Cu(111). a) High resolution STM image with b) structuralmodel. The Fe center is labeled in red. c) Determination of the adsorption site: a hexagonal lattice is fitted to thepositions of co-adsorbed CO molecules revealing that the FePc molecule is aligned with one of the dense-packeddirections of the crystal. The two axes of the molecule are marked in blue and green. [a) 1.9 × 1.9 nm2, c) 4.6 ×6.5 nm2; a) 0.05 V, 0.11 nA; c) -0.2 V, 0.5 nA]
on the lattice at low coverage the exact adsorption site of FePc can be identified (see ref. [29]).
In fig. 5.1c a hexagonal lattice representing the Cu(111) surface is superimposed with the STM
image in such a way that all CO molecules are located on top sites. The superposition of the
structural model of an FePc molecule reveals that it occupies a bridge site with one molecular
axis (main axis) aligned with one of the three dense-packed directions of the crystal and the
other axis being perpendicular to the crystal direction (secondary axis). In fig. 5.1c the main
axis is marked in green and the secondary axis in blue.
The symmetry reduction introduced above is visualized in line profiles across the two molecular
axes. At positive biases around 0.75 V (fig. 5.2a) there is a difference in apparent height between
the two isoindole units on the main axis and on the secondary axis. Along the secondary axis
the isoindole units appear with a higher apparent height than along the main axis. At negative
biases this effect is less pronounced (fig. 5.2b).
However, the bias-dependent symmetry reduction is resolved across the whole molecule in con-
stant height dI /dV maps. Since the tip height is not adjusted during the measurement as for
constant current maps the resolution is higher and the imaging of the LDOS is more accurate
for constant height maps. [163,172] In fig. 5.3 the tunneling current is depicted in the top pan-
els and its derivative in the bottom panels showing a molecule that slightly deviates from the
dense-packed crystal direction (by 4◦). Upon RT deposition the molecules exhibit three different
5.1 Symmetry reduction 73
Figure 5.2: Apparent height across both molecular axes (marked in fig. 5.1c) measured at a) -0.8 V and b) 0.9 V.The difference in apparent height between both axes depends on the voltage. [0.1 nA]
orientations and are all aligned with one of the three crystal directions (within the accuracy of
±2◦, see also [125]). Though, upon annealing to 590 K some molecules deviate up to ±8◦ from
these directions still exhibiting the two-fold symmetry. The annealing experiments are discussed
in detail below.
Figure 5.3: Bias-dependent imaging of FePc on Cu(111) revealing the two-fold-symmetry of the molecule:Constant height dI/dV maps at a) 2 V, b) 1.75 V, c) 0.75 V, d) -0.3 V, e) -2 V. [2.3 × 2.3 nm2, a,b) 0.1 nA, c-e)0.2 nA]
The bias-dependent imaging of the two-fold symmetry of the molecules shows that the isoindole
units on the main axis appear brighter at high positive biases (2 V) and at lower positive biases
(around 0.75 V) the other two (along the secondary axis) appear brighter. At negative biases
the center appears very bright and the macrocycle is approximately uniform in apparent height.
Since the molecule itself is four-fold symmetric, the symmetry reduction is induced by the in-
teraction with the substrate. Snezhkova et al. report that the XP spectra exhibit a core level
shift upon the adsorption of FePc on the Cu(111) surface in comparison to the case of FePc
on graphite, where the interaction with the substrate is weaker. [30] This core level shift is
74 5 ADSORPTION AND COUPLING OF IRON-PHTHALOCYANINE ON CU(111)
attributed to an asymmetric charge transfer from the substrate to the molecule. Therefore, a
bias-dependent imaging of the symmetry reduction is observed in the STM images. Further-
more, the STM data also point to a small geometric contribution. Due to the charge transfer it
is likely that the molecule is slightly bent on the surface.
In conclusion, the symmetry reduction upon adsorption is mainly induced by an electronic ef-
fect, the asymmetric charge transfer. Based on preliminary DFT calculations a minute geometric
contribution can not be excluded. [30]
5.2 Polymerization reactions
Due to its similarity to porphyrins it is expected that dehydrogenation and coupling reactions
of FePc molecules can be induced on the Cu(111) surface. Indeed, annealing a sub-ML of FePc
at 590 K leads to the formation of oligomers. The desorption rate at this temperature is small,
therefore post-annealing is sufficient to induce coupling. Not all molecules are coupled after
an annealing duration of 10 min, however as mentioned above for some single molecules their
orientation towards the dense-packed directions of the Cu(111) surface is slightly changed and
deviates up to ±8◦.
Figure 5.4: Polymerization of FePc upon annealing at 590 K. a) Overview STM image. b,c) Oligomers withstructural models superimposed. Since several hydrogen atoms overlap it is assumed that the molecules dehydro-genate and partially couple. [a) 13.1 × 14.3 nm2, b) 4.0 × 3.6 nm2, c) 4.4 × 3.6 nm2, a) -0.8 V, 0.1 nA, b) 0.5 V,0.1 nA, c) -0.25 V, 0.1 nA]
5.3 Summary 75
The FePc oligomers are limited in length (up to approximately 20 units) and show no long-
range order (see fig. 5.4a). The superposition of structural models indicates that the molecules
within the oligomers partially dehydrogenate at the periphery since the structural models overlap
(fig. 5.4b,c). In some cases (fig. 5.4b) covalent coupling can be assumed, however, for many other
cases it is not clear how the molecules are coupled (fig. 5.4c).
In XPS measurements a shift of the N 1s and C 1s peaks is observed upon annealing. [173]
Since a dehydrogenation and coupling of only the isoindole units would not significantly shift
the binding energies of the nitrogen atoms, it is assumed that some molecules are fragmented.
This assumption is in good agreement with the STM data where in some cases the structural
models of intact molecules do not fit the units in the oligomers.
5.3 Summary
The origin of the symmetry reduction of FePc/Cu(111) obvious in STM images is investigated
with complementary techniques. The STM data reveal a small geometric contribution and a
more pronounced electronic effect. XPS data show a clear electronic contribution caused by
an asymmetric charge transfer from the substrate to the molecule. With this approach the
symmetry reduction is explained for this system and this method is also applicable to similar
systems.
Upon annealing FePc on Cu(111) polymerization reactions occur. From the STM images it
is clear that some molecules overlap, thus they dehydrogenate and partially couple covalently.
However, XPS and also STM data point to a partial fragmentation of the molecules.
Compared to similar systems described above, the annealing temperature (590 K) is relatively
low for a substantial part of the molecules being decomposed. Porphines and DPPs are observed
to covalently couple upon annealing, but their macrocycles remain mostly intact up to 630 and
650 K, respectively (see ch. 3 and 4.2).
76 5 ADSORPTION AND COUPLING OF IRON-PHTHALOCYANINE ON CU(111)
77
6 Interaction of metalloporphyrins with diatomic gas molecules
The adsorption and binding of small ligands to surface-supported functional molecules is
studied in a variety of fields due to their diverse impact. The reversible binding of gases can
lead to altered optical or electronic properties of the molecules anchored on the surface enabling
their application in gas sensors. [14,15,174,175] Furthermore, the magnetic properties of adsor-
bates can be tuned. [176] It is known that porphyrins and phthalocyanines adsorbed on metal
surfaces can incorporate a metal ion in their macrocycle. [89, 106–108, 171] If this metal ion
has a magnetic moment the ligation of CO, [177,178] O2 [179] or NO [178,180] can change its
spin state. This control of magnetic properties on the molecular scale (magnetochemistry) is of
great importance for molecular spintronics. [176] Finally, adsorbed molecules are well-defined
active sites and their potential to heterogeneously catalyze chemical reactions is explored for a
wide range of different systems, [181, 182] where the underlying substrate strongly influences
the reactivity of the adsorbates. [36, 183,184]
Motivated by the relevance in many biological systems, [11] the interaction of porphyrins con-
taining an Fe center with molecular oxygen is studied. In hemoglobin Fe-porphyrins reversibly
bind oxygen and CO2; under high oxygen pressure in the lungs the Fe centers cooperatively bind
oxygen and it is released e.g. to the protein myoglobin in muscle tissue. Hemoglobin can also
bind CO which is favored over O2 binding by a factor of 200 and that is why CO is very toxic for
humans. [185] However, as mentioned above, the binding affinity of metal centers in porphyrins
highly depends on their chemical environment. [36,184] Another example for this finding is the
adsorption geometry of CO on Fe-TPP molecules on a Ag(111) surface. Seufert et al. reported
the ligation of two CO molecules per Fe-TPP that each bridge a bond of the Fe ion with the
macrocycle. [35] Here, the ligation of O2 on Fe-TPP is studied under similar conditions in order
to determine the adsorption geometry and the difference in binding affinity of the Fe center to
both gas molecules.
In the second part, another surface-induced change in reactivity of a metal center in a por-
phyrin is reported. Recently, it was found that Ru-TPP, which is observed to cleave O2 in
solution, [186] is not reactive to oxygen if adsorbed on a Ag(111) surface. [36] Thus, the inter-
action of the molecule with the surface significantly reduces the reactivity towards O2. On the
other hand, Ti-TPP is expected to be less reactive than Ru-TPP. [36, 187] However, immobi-
lized on the Ag(111) surface Ti-TPP is observed to cleave molecular oxygen and Oxo-Ti-TPP
is formed. The topographic contrast and the spectroscopic differences between Ti-TPP and the
oxidized species will be described.
78 6 INTERACTION OF METALLOPORPHYRINS WITH DIATOMIC...
6.1 Metalation of 2H-TPP with Iron
The metal center in Fe-porphyrins is very sensitive towards oxidation which is why the
compound is difficult to handle under ambient conditions. Therefore, free-base porphyrins are
metalated with Fe in a clean environment (UHV). Buchner et al. showed that the incorporation
of an Fe ion into the macrocycle of 2H-TPP molecules can be achieved by either exposing a
porphyrin layer to Fe or by deposition of Fe prior to the evaporation of the molecules. [107] The
resulting Fe-TPP molecules are characterized in detail in refs. [89, 107,188].
In the following, the metalation of 2H-TPP with Fe is described for both the Ag(111) surface
and for a boron nitride (BN) layer grown on Cu(111).
6.1.1 Metalation on the Ag(111) surface
In order to metalate 2H-TPP molecules with Fe on the Ag(111) surface, 2H-TPP are de-
posited for approximately 3 min (Tcru = 600 K, TS = 300 K) which results in a submonolayer
coverage of dense-packed islands of molecules. Subsequently, Fe is evaporated from an electron
beam evaporator (see ch. 2.1.4) and the sample is annealed at 370 K for 5 min. The percentage
of metalated molecules can be varied by either changing the amount of 2H-TPP on the surface
or the evaporation time of Fe.
Figure 6.1: Metalation of 2H-TPP with Fe on Ag(111). a) Overview STM image with a metalation of more than50%. b-e) Bias-dependent appearance of Fe-TPP (with one 2H-TPP in b). b) -1 V, c) -0.1 V, d) 1.5 V, e) 0.1 V.In b) the main molecular axis is marked by the dotted line. The light and dark blue outlines mark two differentFe-TPP species. [a) 10.3 × 18.3 nm2, b-e) 3.4 × 3.4 nm2; a) -0.82 V, 0.1 nA; b) 0.08 nA, c-e) 0.1 nA]
Figure 6.1a shows a dense-packed island of 2H-TPP and Fe-TPP which is arranged as described
in ch. 4.1. At negative sample biases the Fe-TPP appears with three protrusions on the macro-
cycle, two of which are attributed to the α-pyrrole rings and the central one is induced by the
6.1 Metalation of 2H-TPP with Iron 79
Fe ion. The axis given by the three protrusions is referred to as the main axis of the molecule
(marked by dotted line in fig. 6.1b). Around the macrocycle there are four protrusions marking
the phenyl rings. As depicted in fig. 6.1b,c, there are slightly different appearances of Fe-TPP
at negative biases. The species marked with a light blue outline exhibits broader and higher
protrusions on the two α-pyrrole rings than the dimmer species marked with the dark blue out-
line. At positive biases close to the Fermi level (up to 0.5 V) the bright blue species shows the
same three protrusions with the central one being the highest, whereas for the dark blue species
there are two protrusions on the higher pyrrole rings each and one in the center (fig. 6.1e). This
appearance changes into two elongated protrusions over the whole molecule at higher positive
biases (fig. 6.1d). At these biases the dark blue species appears slightly darker than the bright
blue one.
Since the bright and dark blue species only mark the extreme cases and there are several
molecules that are intermediates between both species, their occurrence might be due to differ-
ent adsorption sites on the underlying lattice of the Ag(111) crystal, as the molecules are not
commensurate with the substrate. [90] This incommensurability results in a moire structure of
molecules with slightly different appearances.
6.1.2 Metalation on a boron nitride layer
The metalation of 2H-TPP adsorbed on an insulating BN film grown on the Cu(111) surface
is observed to be similarly straight-forward as on Ag(111). Firstly, the metal-free 2H-TPP is
deposited onto a BN film (growth conditions described in ch. 2.1.4) which results in the formation
of dense-packed islands. The molecules arrange in the same way as on Ag(111) with the same
lattice constant. In fig. 6.2b an island of 2H-TPP on BN is depicted where the moire caused
by the underlying BN is visible. The lattice mismatch between the BN layer and the Cu(111)
surface induces an electronically corrugated interface. Therefore, the molecules within one island
are positioned on electronically different adsorption sites leading to different energetic positions
of the HOMO and LUMO (see also [189]). Thus, the moire pattern is visible on the molecular
islands if occupied or unoccupied states of the molecules are probed.
As shown in fig. 6.2b the LUMO of 2H-TPP appears as four elongated lobes with a depression in
the center (outline of one molecule is marked in green). At small sample biases (within the band
gap of the molecule) it appears darker and only the topography is imaged (e.g. in fig. 6.2c with
green outline). The HOMO was not resolved stably. The energetic positions of the HOMO and
LUMO are determined via STS. In fig. 6.3b two main peaks are visible in the spectrum acquired
on a 2H-TPP, with the onset of the HOMO around -1.8 V and the onset of the LUMO around
1.5 V. As mentioned above, these values can shift up to several 100 mV depending on the lateral
position of the respective molecule on the BN moire. The average band gap, determined from
measurements on several molecules, amounts to 3.4 ± 0.1 V. This value is very similar to the
electronic band gap of 2H-TPP on graphene of 3.3 V, however, it is significantly larger than on a
80 6 INTERACTION OF METALLOPORPHYRINS WITH DIATOMIC...
Figure 6.2: Metalation of 2H-TPP on BN on Cu(111) with Fe. a) STM image of a dense-packed island of2H-TPP and a few Fe-TPP. b) 2H-TPP island with the moire of the underlying BN visible. The outline of theLUMO of one 2H-TPP is marked in green. c) 2H-TPP and Fe-TPP (outline in blue) imaged in the band gap. d)LUMO of 2H-TPP and Fe-TPP. [a) 87.5 × 36.9 nm2, b) 21.2 × 19.2 nm2, c,d) 4.6 × 4.6 nm2; a) 1.4 V, 0.08 nA;b) 2.5 V, 0.06 nA; c) -1.5 V, 0.06 nA; d) 1.7 V, 0.03 nA]
Au(111) substrate (2.4 V). [190] Gas phase calculations yield an electronic band gap of 4.39 and
4.71 V for 2H-TPP. [191, 192] Due to the strong interaction of molecules with metal substrates
their band gaps are reduced upon adsorption. Therefore, the interaction with an insulating layer
as BN or graphene seems to be smaller (see also ch. 7.3).
The spectrum on the bare BN film (fig. 6.3a) shows the expected field emission resonances. [71]
In a next step, iron is deposited onto the sample from a filament in the OMBE (I = 4.4 A, V
= 2.8 V, TS = 330 K, td = 10 min). In large-scale images no difference to the 2H-TPP sample
is apparent (see fig. 6.2a). However, in high-resolution images it is obvious that the center of
the molecule appears as a protrusion for some of the molecules which is attributed to an Fe ion
incorporated into the macrocycle. At negative biases, within the band gap of the molecules,
2H-TPP and Fe-TPP molecules can be clearly distinguished (fig. 6.2c). The LUMO of Fe-TPP
is very similar to the one of 2H-TPP except for the additional protrusion in the center of the
Fe-TPP and its lower onset voltage (similar to another porphyrin metalated with Co [193]). The
energetic shift of the electronic states depending on the position on the moire is also observed
for the Fe-TPP (fig. 6.3c).
In fig. 6.4 the energetic shift of the LUMO between neighboring molecules is illustrated. At 1 V
sample bias nearly all molecules appear dark and only two Fe-TPP molecules on the left exhibit
6.1 Metalation of 2H-TPP with Iron 81
Figure 6.3: Scanning tunneling spectroscopy on 2H-TPP and Fe-TPP on BN: dI/dV spectra on a) BN onCu(111) showing the field emission resonances, b) 2H-TPP on BN and c) Fe-TPP on BN. For both 2H-TPP andFe-TPP the onset of the occupied and unoccupied states varies with the adsorption site. d) STM image showingthe positions where the spectra are recorded (marked by colored circles). The dark areas are 2H-TPP moleculeswith a smaller apparent height. [7.5 × 5.9 nm2; 1.7 V; 0.04 nA]
Figure 6.4: Fe-TPP and 2H-TPP on BN on Cu(111). Onset of the LUMO of the Fe-TPP molecules at differentbiases depending on the adsorption site. [6.1 × 5.0 nm2; 0.03 nA; a) 1 V, b) 1.1 V, c) 1.2 V, d) 1.3 V]
the shape of the LUMO. With increasing sample bias more molecules appear with a greater
apparent height and at 1.3 V only the 2H-TPP molecules appear dark since their LUMO lies at
a higher energy.
In analogy to the Co case, [193] these data show a successful metalation of 2H-TPP on BN.
Importantly, this is the first demonstration of an in-situ Fe metalation of tetrapyrroles on a
non-metallic substrate.
82 6 INTERACTION OF METALLOPORPHYRINS WITH DIATOMIC...
6.2 Interaction of Fe-TPP on Ag(111) with CO and O2
As described in refs. [35, 194] the exposure of Co-TPP and Fe-TPP on a Ag(111) surface
to CO, if the sample is cooled to approximately 10 K, results in a specific binding of CO on
the TPP. In contrast to similar systems as e.g. metal-phthalocyanines (Pc) a new adsorption
geometry was found. For different surface-anchored metal-Pcs a single CO molecule can bind
to the metal center with its axis perpendicular to the surface, [177, 178] whereas for Co-TPP
and Fe-TPP the ligation of two CO molecules per TPP is observed. In the STM images the
decorated Fe-TPP appears cross-like with two additional protrusions on the axis perpendicular
to the main axis (secondary axis). The configuration depicted in fig. 6.5a is assigned to the
ligation of two CO molecules that bridge the bond between the iminic nitrogen atoms to the Fe
ion. The two CO-related protrusions on the molecule in fig. 6.5b appear noisy and are attributed
to only one CO molecule switching between the two possible binding sites. Since the switching
rate is higher than the scanning speed of the STM the two protrusions are imaged noisy.
Figure 6.5: a) (CO)2/Fe-TPP and b) CO/Fe-TPP on Ag(111). [2.2 × 2.2 nm2; -0.5 V, 0.1 nA]
Additionally, a minority Fe-TPP species is observed after the dosage of CO. In fig. 6.6a an island
of 2H-TPP and Fe-TPP is shown with one (CO)2/Fe-TPP (marked by green circle) and several
molecules with a bright protrusion in the center and a significantly smaller apparent height of
the macrocycle than the majority Fe-TPP (marked by gray circle). These molecules are modified
Fe-TPP molecules as shown in fig. 6.6b where some of them turn into Fe-TPP or CO-decorated
Fe-TPP during scanning with the STM tip. The appearance of the center of these molecules
depends on the tip termination and can either be a protrusion (in fig. 6.6c) or it can be of
the same apparent height as the macrocycle (in fig. 6.6d). The images in fig. 6.6c and d were
acquired on the same area with the only difference that the tip termination changed between
both images. Figures 6.6e and f show the same location on the surface as well, where a minority
Fe-TPP species changes to an Fe-TPP between the acquisition of the images.
As this minority species only appears after dosing CO and as shown in fig. 6.6 it can turn into
a Fe-TPP or CO-decorated Fe-TPP and the other way around, it is tentatively assigned to a
6.2 Interaction of Fe-TPP on Ag(111) with CO and O2 83
Figure 6.6: Minority species after CO dosage onto Fe-TPP on Ag(111). a) Overview STM image with (CO)2/Fe-TPP (green circle), Fe-TPP (blue circle) and minority species (gray circle). b) (CO)2/Fe-TPP and Fe-TPP turninto minority species during scanning. c,d) Same area scanned with different tip termination. In c) the minorityspecies appear with a protrusion in the center and in d) with a depression. e,f) The minority species molecule(e) turns into an Fe-TPP (f). [a) 11.2 × 7.9 nm2; b) 10.1 × 4.6 nm2; c,d) 5.2 × 4.9 nm2; e,f) 4.3 × 1.7 nm2; a,e,f)-0.3 V, 0.09 nA, b) -0.4 V, 0.1 nA, c,d) -0.3 V, 0.07 nA]
reversible attachment of a ligand.
In order to study the interaction of Fe-TPP on Ag(111) with the biologically relevant molecule
O2, it is dosed via a leak valve onto the sample held between 10 to 20 K (p: 1.0 · 10−7 mbar,
t = 30 s). Because of the low sticking probability of CO on Fe-TPP at elevated temperatures, [35]
O2 is dosed under cold conditions as well. This leads to a decoration of nearly all Fe-TPP
molecules on the surface (see fig. 6.7a). The decorated molecules appear very similar to CO-
ligated Fe-TPP (cross shape). Also similar to the adsorption of CO is the fact that the O2
molecules are easily moved by the STM tip. In fig. 6.7b abrupt changes in neighboring scan lines
indicate a modified appearance of the molecules during scanning.
Due to the similar geometry to (CO)2/Fe-TPP, also for O2 on Fe-TPP it is assumed that two gas
molecules bind to the macrocycle bridging the bond between the iminic nitrogen atom and the
Fe ion. Moreover, the switching configuration described above (only one gas molecule adsorbed)
is observed for O2 on Fe-TPP as well (fig. 6.7d). To sum up, both gas molecules adsorb in similar
geometries (one or two gas molecules per Fe-TPP) on Fe-TPP/Ag(111).
Importantly, in the STM data it can be distinguished if the Fe-TPP is decorated with either CO
or O2. In the case of O2 on Fe-TPP four additional protrusions are present on the secondary axis
of the molecule (fig. 6.7c) which are imaged as only two protrusions with broader tips (fig. 6.7a).
84 6 INTERACTION OF METALLOPORPHYRINS WITH DIATOMIC...
Figure 6.7: Molecular oxygen (O2) on Fe-TPP on Ag(111). a) Nearly all Fe-TPP molecules are decoratedafter dosing O2 for 30 s at 1 · 10−7 mbar. The molecules appear very similar to (CO)2/Fe-TPP (cross-shape). b)Scanning over the decorated molecules with the STM tip induces detachment and movement of the gas molecules.c) Stable configuration of Fe-TPP decorated with O2 and d) labile configuration (imaged noisy). [a) 10.8 ×7.4 nm2; b) 5.9 × 5.1 nm2; c,d) 1.8 × 1.8 nm2; a) -0.4 V, 0.06 nA, b) -0.8 V, 0.1 nA, c) -0.4 V, 0.05 nA, d) -0.4 V,0.07 nA]
In contrast, for CO on Fe-TPP only two protrusions appear on the secondary axis (fig. 6.5).
A more quantitative discrimination between CO and O2 adsorbed on Fe-TPP is the distance
between the additional protrusions on the secondary axis. For (O2)2/Fe-TPP the separation
of the two inner and the two outer protrusions is measured each for several molecules and
compared to the separation of the two protrusions on (CO)2/Fe-TPP in fig. 6.8. With these two
protrusions being significantly closer to each other than the outer ones of the (O2)2/Fe-TPP it
can be differentiated which gas molecules are ligated to an Fe-TPP.
Figure 6.8: Distance between additional protrusions on Fe-TPP attributed to the adsorption of CO and O2. For(O2)2/Fe-TPP four additional protrusions appear and for (CO)2/Fe-TPP only two. Their spacings (marked byblue line) are significantly different from each other so that it can be distinguished in the STM images with whichgas molecules the Fe-TPP interacts. [1.5 × 1.5 nm2; -0.5 V; 0.05 nA, 0.1 nA, 0.05 nA]
As described above, the Fe-TPP appears in slightly different configurations, referred to as bright
and dark species. The difference between these two is still visible with two oxygen molecules
ligated to the Fe-TPP. For the bright Fe-TPP species the two protrusions at the center of the
6.2 Interaction of Fe-TPP on Ag(111) with CO and O2 85
molecule are very close (on the left in fig. 6.9a), whereas for the dark Fe-TPP species they are
clearly separated (on the right in fig. 6.9a). The height profile over the secondary axis of both
molecules reveals the slight differences between the bright and the dark Fe-TPP species. The
shape of the protrusions on the dark Fe-TPP species (dark red line) is symmetric towards the
center and all four protrusions appear slightly lower than for the bright Fe-TPP which shows
asymmetric peak heights towards the center (bright red line).
Figure 6.9: Two different appearances of oxygen on Fe-TPP: a) Oxygen adsorbed on the bright (left) and dark(right) Fe-TPP species. b) Height profiles along the axis perpendicular to the main axis of the molecules on bothFe-TPP species decorated with oxygen. The bright species appears asymmetric in height in the center. [2.9 ×2.4 nm2; -0.5 V, 0.05 nA]
The STM images shown in fig. 6.10 were acquired after dosing O2 and CO onto the cold sample.
(CO)2/Fe-TPP is marked by a green circle in fig. 6.10a and the two different (O2)2/Fe-TPP
species by a light and a dark red circle each. During scanning over the surface with the STM tip
the gas molecules are moved and they can also be exchanged between molecules. In fig. 6.10b
and c several (O2)2/Fe-TPP and one CO-decorated Fe-TPP are depicted. Their appearance
only changes marginally when the bias voltage is reversed.
In conclusion, O2 adsorbs in a similar way as CO on Fe-TPP/Ag(111) and by their appearance
in STM images (O2)2/Fe-TPP and (CO)2/Fe-TPP can be differentiated.
The binding of CO and O2 to Fe-TPP adsorbed on a Ag(111) surface is very different from the
situation in the protein hemoglobin which reversibly binds oxygen in our body. The four Fe-
porphyrin centers in hemoglobin only bind one gas molecule each. [185, 195, 196] Furthermore,
in hemoglobin the binding of CO is favored by a factor of 200 over the binding of O2. [185]
However, the affinity of Fe-TPP adsorbed on Ag(111) towards the binding of either CO or O2
is very similar. The amount of dosed gas molecules and subsequently ligated porphyrins was
similar in both cases. Moreover, temperature-programmed desorption experiments show that
both, CO and O2, desorb from Fe-TPP at a temperature of 30 K [197] pointing to a very small
but similar binding energy.
In hemoglobin the Fe center of the porphyrin binds to the four nitrogen atoms of the macrocycle,
86 6 INTERACTION OF METALLOPORPHYRINS WITH DIATOMIC...
Figure 6.10: Dosing CO and O2 on Fe-TPP on Ag(111) yields (CO)2/Fe-TPP (green circle), and O2 adsorbed onthe bright (marked by light red circle) and the dark (marked by dark red circle) Fe-TPP species. The decoratedmolecules exhibit similar appearances at negative (b) and positive (c) sample biases. [a) 4.6 × 5.4 nm2; b) 5.9 ×2.4 nm2; a) -0.7 V, 0.01 nA, b) -0.3 V, 0.04 nA, c) 0.4 V, 0.04 nA]
to a histidine residue below the plane of the macrocycle and to the oxygen above. On the
Ag(111) surface, the interaction of the Fe with the surface differs from the interaction with the
histidine, probably lowering the binding energy of oxygen. Due to the observation of strong
interactions and charge transfer between metal centers in porphyrins and the underlying metal
surfaces, [107, 184, 198] it is likely that the Fe center interacts stronger with the Ag substrate
than with the histidine in hemoglobin changing the reactivity towards adsorbates. Moreover, in
the protein the oxygen molecule is substantially stabilized by hydrogen bonds to other ligands
above the macrocycle which is not the case on the surface. [185] Therefore, the binding energy
of O2 to the Fe center in the porphyrin molecule is reduced in the model system on the surface
in comparison to hemoglobin.
In order to reduce the strong interaction of the Fe center with the substrate such that the Fe-
oxygen bond becomes stronger, a less reactive surface could be employed, as e.g. an insulating
BN film on top of a metal surface. Preliminary experiments point to a very weak interaction of
Fe-TPP/BN/Cu(111) with molecular oxygen, however, only a few molecules could be resolved.
Therefore, the results need to be confirmed for a larger number of molecules.
6.3 Interaction of Ti-TPP on Ag(111) with O2
Another approach to increase the interaction of O2 with a surface-anchored metalloporphyrin
is to change the metal center. In the following, Ti will be addressed instead of Fe.
The oxidation of Ti-TPP immobilized on the Ag(111) surface is believed to be of great impor-
tance for photocatalysis. In 1972 is was found that TiO2 can photocatalytically split water, [199]
however the efficiency is very low because only a small fraction of the sunlight is absorbed and a
6.3 Interaction of Ti-TPP on Ag(111) with O2 87
thermodynamically favored backwards reaction produces water again. This backwards reaction
is predicted to be suppressed for the compound Oxo-Ti-porphyrin. [200] Indeed, Morawski et al.
observed that microcrystalline TiO-TPP can split water. [201] Therefore, TiO-TPP molecules
are prepared and characterized under controlled conditions in UHV in order to gain a funda-
mental understanding of the system for its future applications.
6.3.1 Metalation of 2H-TPP with Titanium
As described above, the metalation of 2H-TPP molecules on the Ag(111) surface is straight-
forward for many different metals. [89,106–108] Here, a submonolayer of 2H-TPP (Tcru = 600 K,
TS = 310 K, td = 5 - 7 min) is metalated with Ti by the deposition of 0.02 nm of Ti from a
ribbon evaporator (monitored by a quartz microbalance) followed by annealing at 500 K for
10 min in order to facilitate the metalation. This procedure results in islands of molecules with
different contrast (fig. 6.11a) and a few partially flattened 2H-TPP (cf. ch. 4.1). Approximately
62 % of the molecules appear with a protrusion in the center instead of a depression and two
additional protrusions on the α-pyrrole rings. This shape is very similar to the appearance of
other metalated porphyrins as Co-TPP and Fe-TPP on Ag(111) (see e.g. ch. 6.1.1).
Figure 6.11: Metalation of 2H-TPP with Ti on Ag(111). a) Dense-packed island of molecules: Ti-TPP appearswith three bright lobes and 2H-TPP appears darker. b) to i) Bias-dependent appearance of Ti-TPP. b) -1 V, c)-0.5 V, d) -0.3 V, e) -0.1 V, f) 0.8 V, g) 0.5 V, h) 0.3 V, i) 0.1 V. [a) 9.0 × 15.8 nm2; b,f) 3.8 × 2.9 nm2; c-e,g-i) 3.5× 3.5 nm2; a,b,f) 0.11 nA, c-e,g-i) 0.2 nA]
In figure 6.11b-i Ti-TPP molecules are depicted at different sample biases. At -1 to -0.3 V the
two protrusions on the pyrrole rings appear brighter than the central protrusion which is related
to the HOMO being located on these two pyrrole rings (see below). Close to the Fermi level
the three protrusions appear with a similar apparent height. The shape of the LUMO (at 0.3
to 0.5 V) is very similar to the shape of Fe-TPP close to the Fermi level, namely a protrusion in
the center and two lobes on each of the α-pyrroles. At higher positive biases Ti-TPP appears
with a smaller apparent height than 2H-TPP and exhibits only two elongated lobes (fig. 6.11f).
88 6 INTERACTION OF METALLOPORPHYRINS WITH DIATOMIC...
Figure 6.12: N 1s XP spectra on an increasing amount of 2H-TPP metalated with Ti on Ag(111) (includingfits): 1) 2H-TPP ML, 2) 20 % of the Ti saturation coverage (sat. cov.) evaporated onto the 2H-TPP ML at RT,3) subsequent annealing to 400 K, 4) additional 26 % of the Ti sat. cov. evaporated at RT, 5) annealing to 500K. Adapted from [202]
The chemical change of the 2H-TPP molecules is studied as well via XPS (under the supervision
of David A. Duncan, see ref. [202]). In the case of only 2H-TPP on the surface the N 1s spectrum
shows two peaks (fig. 6.12 top spectrum), one corresponding to the iminic and the other one to
the pyrrolic nitrogen atoms. With an increasing amount of Ti evaporated onto the surface and
annealing steps another nitrogen-related peak appears which is dominant after the deposition
of enough Ti to metalate half a monolayer of 2H-TPP (fig. 6.12 bottom spectrum). Thus, the
four nitrogen atoms are chemically equivalent because of the incorporation of the Ti ion into
the macrocycle.
The electronic structure of Ti-TPP on Ag(111) is probed via STS. As depicted in fig. 6.13a the
HOMO is located around -0.25 V and it is more pronounced on the α-pyrrole rings than on the
Ti ion. This finding is in good agreement with the shape of the HOMO on Ti-TPP shown in the
dI /dV map recorded at -0.3 V (fig. 6.13b). Very similar to Co-TPP and Fe-TPP the HOMO is
located on the two α-pyrrole rings.
The first peak in the unoccupied range is around 0.23 V which is reflected in the STM images
by the appearance of two lobes on each α-pyrrole ring.
In conclusion, with the combination of the different techniques it is shown that 2H-TPP molecules
can be metalated with Ti on the Ag(111) surface.
6.3 Interaction of Ti-TPP on Ag(111) with O2 89
Figure 6.13: Scanning tunneling spectroscopy on Ti-TPP on Ag(111). a) Two spectra recorded on the center ofthe molecule and on the α-pyrrole, respectively. The HOMO at -0.25 V is more pronounced on the α-pyrrole andthe LUMO is located around 0.23 V. b) Topography image and dI/dV map at -0.3 V: The HOMO consists of twolobes on the α-pyrroles. [b) 2.7 × 3.8 nm2; 0.15 nA]
6.3.2 Oxidation of Ti-porphyrins
In order to monitor the oxidation of Ti-TPP on Ag(111), XPS and NEXAFS were recorded
after dosing O2 onto the sample held at RT. [202] The peak in the Ti 2p XP spectrum is shifted
towards a higher binding energy which points to a change of the oxidation state of the Ti from
2+ to 3+ and thus to an oxidation. Since the N 1s peak remains unchanged it can be assumed
that the oxidized Ti is still incorporated in the macrocycle. Furthermore, the oxygen K edge
NEXAFS indicates that the Ti-O bond is perpendicular to the surface, i.e. that the oxygen
either points away from the surface or it is below the Ti and points towards the surface. An-
nealing experiments indicated that the Ti-O bond is stable up to 725 K.
In the STM experiments the preparation chamber is backfilled with O2 to a pressure of 1 ·10−7 mbar for 16 min while the sample is kept at RT. After subsequent cooling several different
species are observed. Nearly 50 % of all molecules are identified as 2H-TPP and only a small
amount of approximately 6 % appears as Ti-TPP. As the metalation efficiency is known from
the previous experiments, it is expected that at least 50 % of the molecules are metalated. Thus,
all other molecules than 2H-TPP are assigned to Ti-TPP interacting with oxygen.
As depicted in fig. 6.14 three main different species are observed apart from Ti-TPP, 2H-TPP
and a few additional minority species that could not be identified. All three species shown in
fig. 6.14 appear very similar to 2H-TPP except for the center of the molecules. The majority
species (fig. 6.14a) exhibits a slit in the center of the molecule at negative sample biases and
at positive biases it appears as two elongated lobes where the 2H-TPP shows four lobes. The
second species depicted in fig. 6.14b has the same apparent height in the center of the molecule
as on the macrocycle at negative biases and the third species has a protrusion in the center
(fig. 6.14c). At positive biases these two species appear with four lobes on the macrocycle that
90 6 INTERACTION OF METALLOPORPHYRINS WITH DIATOMIC...
Figure 6.14: Three Ti-TPP species observed after dosing O2 imaged at negative (top) and positive (bottom)sample biases. a) Majority species with a slit in the center of the macrocycle (outline marked in blue). b) Minorityspecies with the center at the same apparent height as the macrocycle (outline marked in dark blue). c) Minorityspecies with a protrusion in the center (outline marked in violet). [3.1 × 2.5 nm2; top panels: -0.3 V, bottompanels: 1 V; 0.12 nA]
are very similar to the LUMO of 2H-TPP and with a protrusion in the center which is brighter
for the third species.
Based on the XPS and NEXFAS measurements, [202] it is deduced that the molecular oxygen
is cleaved on the surface and that only one oxygen atom binds to the Ti ion in the molecules.
Thus, oxotitanium-TPP (TiO-TPP) is formed and the occurrence of only one TiO-TPP species is
expected. However, approximately 30 % of the molecules appear as the first TiO-TPP species, re-
ferred to as blue TiO-TPP (marked in fig. 6.14a), only 4 % as the dark blue TiO-TPP (fig. 6.14b)
and 8 % as the violet TiO-TPP (fig. 6.14c). The identification of all different species is based on
STM images acquired at positive and negative biases at the same spot on the surface using the
same tip. The corresponding statistics are given in tab. 7.
Molecule Occurrence
2H-TPP 46± 4 %Ti-TPP 6± 1 %
Blue TiO-TPP 30± 3 %Dark blue TiO-TPP 4± 1 %
Violet TiO-TPP 8± 2 %Other 7± 1 %
Table 7: Occurrence of different species after dosing O2 onto 2H-TPP and Ti-TPP on Ag(111).
In contrast to the interaction of Fe-TPP with CO and O2, no tip-induced movement of adsor-
bates is observed for the TiO-TPP. Nevertheless, some of the molecules can undergo tip-induced
6.3 Interaction of Ti-TPP on Ag(111) with O2 91
changes in appearance. Figure 6.15a to c shows the same area on the surface and between the
acquisition of the images ST spectra were recorded in the bias range of -1 to 1.2 V. Firstly, the
2H-TPP molecule marked by the green circle in fig. 6.15a tautomerizes during STS and the other
tautomer is depicted in fig. 6.15b. Secondly, the circled blue TiO-TPP turns into a dark blue
TiO-TPP in fig. 6.15b and back into a blue one (fig. 6.15c) after a voltage pulse of -2 V in close
proximity.
Figure 6.15: Tip-induced change of appearance of different TiO-TPP species. a) to b) 2H-TPP (green) tau-tomerizes and the blue TiO-TPP turns into a dark blue TiO-TPP. b) to c) The dark blue TiO-TPP turns backinto a blue TiO-TPP. The tautomerization occurs during STS on the 2H-TPP and the switching of the TiO-TPPstakes place during STS on other molecules close by. d) to e) A dark blue TiO-TPP turns into a dark speciesduring STS in close proximity. f) to g) A blue TiO-TPP turns into a dark species during STS on the molecule.[a-c) 9.3 × 4.8 nm2; d,e) 5.4 × 2.1 nm2; f,g) 3.8 × 4.9 nm2; a-c,f,g) 0.6 V, d,e) 0.7 V; a) 0.2 nA, b,c) 0.25 nA, d,e)0.3 nA, f,g) 0.15 nA]
Furthermore, both the dark blue (fig. 6.15d,e) and the blue TiO-TPP (fig. 6.15f,g) can turn into
a dark species with a significantly lower apparent height at different biases. Only at negative
biases the four phenyl rings are visible and a protrusion in the center. Between fig. 6.15d,e a ST
spectrum between -0.2 to 2 V is recorded and several spectra from -1 to 1.2 V between fig. 6.15f,g.
The transformation into the dark species was only once observed to be reversible, but mostly
during scanning and especially during STS measurements the amount of dark species increases.
At biases above ± 2 V several molecules change at the same time. Thus, the dark species might
92 6 INTERACTION OF METALLOPORPHYRINS WITH DIATOMIC...
be chemically changed or decomposed by the tip.
In summary, the following tip-induced transformations are observed:
Blue TiO-TPP→ Dark blue TiO-TPP
Dark blue TiO-TPP→ Blue TiO-TPP
Blue TiO-TPP→ Dark species
Dark blue TiO-TPP→ Dark species
Consequently, the statistics in tab. 7 have to be treated carefully because tip-induced changes
cannot be excluded in the STM images. Moreover, the blue and the dark blue TiO-TPP seem to
be the same species in two different conformations whereas the violet TiO-TPP is not affected
by the tip.
In order to clarify the nature of the different species and to probe the electronic structure of
the different species STS are recorded. The spectra on Ti-TPP and 2H-TPP are plotted as a
comparison in fig. 6.16a. The blue TiO-TPP shows a peak in the unoccupied range around 0.6 V
and a step at 0.1 V, whereas the dark blue and violet TiO-TPP only show the step at 0.1 V and
a broad increase towards higher voltages. The overall shape of the ST spectrum is very similar
for 2H-TPP and the blue TiO-TPP. Moreover, the energetic position of the LUMO varies for
both molecules in a similar range. In fig. 6.16b for both molecules two spectra are plotted for
molecules on different adsorption sites. The peak shape is similar in all cases but their energetic
position is shifted. The only difference is that the 2H-TPP tautomerizes at higher biases as e.g.
in the light green spectrum in fig. 6.16b (at 0.8 V).
Figure 6.16: Scanning tunneling spectroscopy on TiO-TPP, Ti-TPP and 2H-TPP on Ag(111). a) The spectraof the blue TiO-TPP and 2H-TPP are very similar, as well as the ones of the dark blue and violet TiO-TPP. AllTiO-TPP species are spectroscopically different from Ti-TPP. b) The energetic position of the LUMO dependson the adsorption site for 2H-TPP and the blue TiO-TPP. For each of them two spectra are plotted in order toindicate their possible variations.
The fact that the spectra of the dark blue and the violet TiO-TPP have the same shape and
that their appearance in the STM images is very similar as well points to only minor differences
between the two species which might be explained by different adsorption sites. Taking into
6.4 Summary 93
account that the tip can induce the reversible transformation from a blue to a dark blue TiO-
TPP, all the species might be attributed to TiO-TPP, present in at least three configurations
on the surface.
As described above, the spectra on the blue TiO-TPP are very similar to the ones on 2H-TPP
but show pronounced differences in comparison to Ti-TPP. This finding can be explained by an
altered interaction of the Ti ion with the macrocycle upon oxidation (as observed for NO/Fe-
TPP [194]). Since it is not clear if the oxygen atom is above or below the plane of the macrocycle,
it is possible that the Ti ion is lifted or lowered from its former position.
6.4 Summary
To conclude, it is shown that the ligation of small gas molecules to metal-porphyrins on a
support is strongly influenced by the interaction of the metal ion to the substrate. In the first
part, the on-surface metalation of 2H-TPP with Fe on both the Ag(111) surface and an insu-
lating BN layer grown on Cu(111) is described. On the Ag(111) surface, where the interaction
of the Fe ion to the substrate is strong in comparison to the BN layer, CO and O2 can only be
ligated to the adsorbed molecules if the sample is cooled to 20 K or lower. In the case of CO on
Fe-TPP/Ag(111) two CO molecules can be adsorbed and they each bridge a bond of the Fe ion
to the macrocycle. [35] In a second possible configuration a single CO molecule switches between
these two adsorption sites. Due to the similar appearance in STM images it is assumed that O2
ligates to Fe-TPP/Ag(111) in a similar way as CO. Nevertheless, the structure of the additional
protrusions on the Fe-TPP is slightly different for both gases so that they can be distinguished
in the STM images.
Temperature-programmed desorption experiments show that both CO and O2 desorb from Fe-
TPP/Ag(111) at 30 K. [197] This low affinity towards the two gas molecules can be explained
by a strong interaction of the Fe ion with the substrate (covalent character [184]). Moreover, in
hemoglobin it is observed that the position of the Fe ion relative to the plane of the macrocycle
(above or below) influences the affinity to the gas molecules as well. [185] Therefore, future
experiments could be carried out on a surface with a reduced interaction with the Fe ion as e.g.
a BN layer grown on Cu(111).
In the second part, 2H-TPP molecules are metalated with Ti on the Ag(111) surface. Subse-
quent exposure to O2 leads to the formation of oxo-Ti-TPP which is monitored by XPS and
NEXAFS. In the STM observations three new species are identified after oxidation. However,
two of them seem to be only different configurations of the same species since they could be
reversibly switched by voltage pulses from the tip. Furthermore, the third species is spectro-
scopically and topographically very similar to one of the two configurations. Thus, the three
species might be different configurations of only one TiO-TPP species. For all three of them the
tunneling spectra more resemble the ones of 2H-TPP than of Ti-TPP pointing to a change of
94 6 INTERACTION OF METALLOPORPHYRINS WITH DIATOMIC...
the interaction of the Ti ion with the macrocycle upon oxidation.
These findings that Ti-TPP on Ag(111) is oxidized at relatively low exposures to O2 and that
the Ti-O bond is stable up to 725 K fits nicely into a trend in reactivity across the periodic
system. Ru-TPP was observed to be unreactive towards O2 [36] and the Mn-O bond in oxidized
Mn-TPP molecules is only stable up to 445 K. [203] Hence, Ti being located at an even smaller
group number in the periodic system is the most reactive of the three elements. With the ob-
servation of this trend future catalysts can be developed with tailored reactivity.
Moreover, the formation of TiO-TPP in this controlled environment enables further investiga-
tions on the photocatalytic activity of this system.
95
7 Intermolecular interactions at the model interface of an or-
ganic solar cell
Organic solar cells comprise a variety of advantages in comparison to inorganic photovoltaics
because they can be produced at lower cost, with less weight and they exhibit high absorption
coefficients. [204] Some organic solar cells are transparent in parts of the visible range of the
sunlight enabling e.g. an incorporation in windows. [205] One common type of organic solar
cell consists of a solution-based bimolecular heterojunction which enables facile processing and
the properties of the device can be tuned by employing different molecules. [206,207]
Here, a model system for a bimolecular organic solar cell is investigated with the molecules B,O-
chelated azadipyrromethene (BO-ADPM) and C60 forming the heterojunction. In the device C60
acts as the electron acceptor and it was shown that C60 supports a rapid charge separation, [208]
whereas the BO-ADPM molecules exhibit a high absorption coefficient and thus are responsible
for the absorption of the incident light and act as the donor in the junction. [72] The absorption
of photons leads to the formation of a bound electron-hole pair (exciton) which diffuses to the
interface. The drop in potential between both materials causes the dissociation of the exciton and
thus the electron is located in the acceptor layer and the hole in the donor layer. Subsequently,
both charge carriers are transported separately to the metal contacts. [204,206]
Hence, at the interface important processes that influence the efficiency of the device take
place. In order to optimize the performance of the solar cell it is required to understand which
parameters influence its efficiency. Recent studies show that the geometry and the arrangement
of the two different molecules at the interface have impact on the exciton dissociation [209] and
on the overall efficiency. [210–213] Therefore, in the following a model system of a device which
was studied by Leblebici et al. [72] is investigated in a controlled and solvent-free environment.
The interface of the device is simplified in such a way that one layer of the acceptor (C60) and
of the donor (BO-ADPM) molecules are deposited onto a Ag(111) surface acting as the back
contact. With the STM tip the junction is contacted from the top. In this configuration the
interaction of both molecules at the interface is investigated and the electronic band gap is
measured.
7.1 BO-ADPM on Ag(111)
At first, the donor molecule BO-ADPM is studied on the Ag(111) surface in order to compare
its appearance and electronic structure to the adsorption on a layer of C60. BO-ADPM exhibits
a non-planar conformation in the gas phase. The structural model obtained by Hyper-Chem
(AM1 method) shows that for an isolated species the two oxy-phenyl moieties are bent away
from each other resulting in an opening angle of approximately 50◦ (top view in fig. 7.1a and side
96 7 INTERMOLECULAR INTERACTIONS AT THE MODEL INTERFACE...
view in fig. 7.1b). The two phenyl rings are slightly tilted. Upon deposition onto the Ag(111)
surface (Tcru = 490 K, TS = 300 K and td = 23 min) the non-planarity is preserved. As apparent
in fig. 7.1c one part of the molecule appears significantly higher than the other parts in the STM
image and it is thus assigned to the upwards-bent oxy-phenyl. Since this contrast is present at
different biases a geometric effect rather than an electronic one can be assumed.
Figure 7.1: Structural model of BO-ADPM: a) top view and b) side view. N, B and O are indicated in blue,green and red, respectively. c) The bending of the two oxy-phenyl rings is preserved on the Ag(111) surface sinceone of them appears with a clearly greater apparent height in the STM images. [2.7 × 2.7 nm2, 0.5 V, 0.2 nA]
In a sub-ML coverage the molecules arrange in dimers, trimers and tetramers on the Ag(111) sur-
face (fig. 7.2a). Monomers are observed only rarely. In a dimer the two molecules are stacked in
such a way that the upwards pointing oxy-phenyl of one molecule overlaps with the downwards-
pointing oxy-phenyl of the other molecule resulting in two protrusions in the center of the dimer
(fig. 7.2b). Similarly, a trimer exhibits three protrusions in the center (fig. 7.2c) and a tetramer
four (fig. 7.2d).
Figure 7.2: BO-ADPM on Ag(111): a) The molecules arrange as dimers, trimers and tetramers. High resolutionimages of b) dimer, c) trimer, d) tetramer. e) Higher coverage. [a) 37.3 × 37.3 nm2, b,c) 4.0 × 4.0 nm2, d) 4.9 ×4.9 nm2, e) 17.8 × 17.8 nm2; a,d) -0.4 V, 0.2 nA, b,c) -0.1 V, 0.2 nA, e) -0.3 V, 0.1 nA]
At a higher coverage the molecules do not assemble in regular islands but still as dimers, trimers
and tetramers (fig. 7.2e).
In fig. 7.3 the dI /dV spectra are depicted for a BO-ADPM monomer, dimer and trimer. All
spectra are acquired on the bright part of the molecules since the other parts only show a
featureless increase of the dI /dV signal in the unoccupied range. The spectrum on the bare
Ag(111) surface is plotted for comparison. All three species exhibit an occupied state around
7.2 Interaction of BO-ADPM and C60 97
-0.4 V which is attributed to the HOMO. Furthermore, only the trimer shows a state in the
unoccupied range around 0.8 V.
Figure 7.3: Scanning tunneling spectroscopy on BO-ADPM on Ag(111). The spectra on the different molecules(monomer, dimer and trimer) are recorded on one of the upwards-pointing oxy-phenyl rings.
7.2 Interaction of BO-ADPM and C60
In order to mimic the interface of the bimolecular solar cell, it is required to deposit the donor
and the acceptor molecule on top of each other. At first, C60 is deposited onto a sub-ML of BO-
ADPM (Tcru = 690 K, TS = 320 K and td = 8 min) which results in a phase separation of both
molecules (fig. 7.4a). C60 forms dense-packed islands on the Ag(111) surface (see [214]) and the
BO-ADPM molecules are arranged as described above (ch. 7.1) and a few decorate the borders
of the C60 islands. Annealing the surface to 490 K does not induce any changes. Therefore, in a
second approach C60 is deposited onto the pristine Ag(111) surface and BO-ADPM is added at
sample temperatures between 130 to 150 K. Thus, the BO-ADPM molecules are less mobile and
some adsorb on top of the C60 islands. If a ML of C60 is predeposited the BO-ADPM cannot be
imaged stably on top. However, also in the sub-ML case the BO-ADPM on top of C60 islands is
easily moved by the STM tip during scanning (see fig. 7.4b). Since the phase separation of both
molecules seems to be preferred on the Ag(111) surface, at higher temperatures the BO-ADPM
has enough energy to move from the C60 islands to the metal.
In fig. 7.4c one BO-ADPM molecule on C60 is imaged stably. In this case the shape of the
molecule is recognizable, however most of the BO-ADPMs are arranged in small agglomerates
on C60 where it is not clear how the single molecules are arranged (e.g. in fig. 7.4b). For the
C60 molecules the LUMO is imaged in fig. 7.4b,c which appears as three lobes (see [214]).
In a third approach a higher coverage of BO-ADPM is deposited onto the Ag(111) surface (td
98 7 INTERMOLECULAR INTERACTIONS AT THE MODEL INTERFACE...
Figure 7.4: Interaction of BO-ADPM and C60 on Ag(111). a) Phase separation of BO-ADPM (left) and C60
(right) at sub-ML coverage. b) BO-ADPM adsorbed on a C60 island is easily moved by the STM tip. c) BO-ADPM monomer on a C60 island, deposited at 150 K. [a) 69.2 × 43.9 nm2, b) 11.9 × 8.0 nm2, c) 3.6 × 2.8 nm2;a) 1.4 V, 0.2 nA, b) 1.4 V, 0.04 nA, c) 0.7 V, 0.08 nA]
= 45 min) and C60 is deposited on top (TS = 200 K, td = 42 min). From the STM images it is
not clear whether C60 is on top of the BO-ADPM molecules or directly on the Ag. Therefore,
lateral manipulation experiments are carried out with the STM tip. By dragging a C60 molecule
at the edge of an island (0.1 V, 5 nA) it can be moved away from it revealing the surface below
its former position (fig. 7.5a to b). When several C60 molecules were moved the bare Ag surface
is revealed (fig. 7.5c). Consequently, the C60 molecules seem to preferentially adsorb directly on
the Ag.
Scanning tunneling spectra on C60 molecules within the islands and on single ones point to an
adsorption on the metal as well. The spectra shown in fig. 7.5d look very similar to spectra
acquired on C60/Ag(111) (cf. [215]). Thus, the phase separation of the two molecules seems to
be preferred also at a higher coverage.
Figure 7.5: Lateral manipulation of C60 deposited onto BO-ADPM. It is not clear if the C60 molecules sit ontop of BO-ADPM or on the bare metal. a) to b) One C60 molecule is moved away from the island with the STMtip (0.1 V, 5 nA). c) Several C60 molecules were moved by the tip. d) STS on different C60 molecules shows nodifference to spectra on C60/Ag(111). [21.3 × 22.1 nm2; 0.7 V, 0.1 nA]
7.3 Measurement of the electronic band gap 99
7.3 Measurement of the electronic band gap
An important property of a bimolecular solar cell is the band alignment of both materi-
als at the interface. The energy offset EDA of the HOMO of the donor (BO-ADPM) and the
LUMO of the acceptor (C60) influences the efficiency of the power conversion process. [72, 210]
In the model system this energy offset can be measured by recording the dI /dV spectrum on
BO-ADPM/C60/Ag(111). The energetic separation of the highest occupied state and the lowest
unoccupied state (electronic band gap) corresponds to the energy offset EDA.
The tunneling spectra are recorded on BO-ADPM agglomerates on C60/Ag(111) after deposi-
tion at 130 to 150 K because this is the most stable configuration. The spectra acquired on
BO-ADPM/C60/Ag(111) differ significantly from the ones on the bare metal and also from
C60/Ag(111). The HOMO and LUMO are mostly measured separately in order to obtain a
better signal-to-noise ratio for both peaks. The HOMO is located around -1.7 V and the LUMO
around 1 V. Both states, HOMO and LUMO, vary by several 100 mV depending on the adsorp-
tion site of the BO-ADPM, thus several spectra are plotted for both states in fig. 7.6.
Figure 7.6: Measurement of the electronic band gap of BO-ADPM/C60/Ag(111). Scanning tunneling spectrain the occupied (a) and unoccupied (b) range for different molecules. For most of the molecules the HOMO andLUMO are measured separately. Both states vary in a range of approximately 300 mV.
Due to the large variation of the peak position of HOMO and LUMO several spectra were
analyzed and average values are obtained. The HOMO is measured 39 times and is on aver-
age positioned at −1.69 ± 0.09 V. The average LUMO amounts to 0.97 ± 0.07 V (measured 35
times). All values are plotted in histograms in fig. 7.7. These values give an average band gap
of 2.7± 0.2 V. As described in ch. 6.1.2 molecules adsorbed on a metal surface strongly interact
with it and in most cases the electronic states are shifted closer to each other. In accordance,
the spectra on BO-ADPM/C60 show a larger band gap than BO-ADPM/Ag(111).
In comparison to the solution-based devices the band gap measured here is slightly larger than
estimated for this system in ref. [72]. Hence, a higher conversion efficiency is expected than
reported in [72]. However, the observation that a phase separation of the two molecules is pre-
100 7 INTERMOLECULAR INTERACTIONS AT THE MODEL INTERFACE...
Figure 7.7: Histograms of the measurement of HOMO (a) and LUMO (b) of BO-ADPM/C60/Ag(111). TheHOMO and LUMO could only be measured 39 and 35 times, respectively, because the molecules are easily movedby the STM tip.
ferred implies a reduced overlap of the orbitals of the different molecules at the interface which
can lower the charge transfer efficiency and thus the efficiency of the whole device.
7.4 Summary
In conclusion, a model system for an organic solar cell is investigated revealing a phase
separation between the donor and acceptor molecules which is likely to lower the efficiency of
the charge transfer and thus the power conversion efficiency of the solar cell.
On the Ag(111) surface the non-planar donor molecule BO-ADPM arranges in dimers, trimers
and tetramers with only a few monomers. The tunneling spectra show broad features derived
from molecular electronic states interacting with the metal surface.
In order to mimic the interface of the solar cell both molecules are co-deposited onto the Ag(111)
surface. However, only the deposition at temperatures below 150 K results in the adsorption of
BO-ADPM on C60/Ag(111). At higher temperatures both molecules separate from each other.
When adsorbed on a layer of C60 the BO-ADPM shows sharper peaks in the tunneling spectra
and they are further separated. By acquiring the energetic position of the HOMO and LUMO
of several molecules and agglomerates of molecules on C60 an average electronic band gap of
2.7± 0.2 V is determined.
Although the model system employed here is very simplified since the fabrication is very different
from the device described in ref. [72] it points to an inefficient charge transfer at the interface
due to the phase separation of the two molecules. In order to study a system more similar to
the device structure the BO-ADPM film could be spin-cast or drop-cast onto the sample before
transferring it into the UHV environment.
101
8 Conclusion and perspectives
The structural and electronic properties of versatile molecules are investigated on clean
metal surfaces as a well-defined laboratory system. For the first time homocoupling of porphine
molecules on a Ag support is reported. The covalent coupling results in an altered electronic
structure of the oligomers, i.e. a reduced electronic band gap. In contrast, TPP molecules are
observed to undergo intramolecular ring-closing reactions. Moreover, the interaction of metallo-
porphyrins with gas ligands is studied as well as the interaction of a metallo-phthalocyanine
with the underlying substrate. In the end, the intermolecular interactions in a model system of
a solar cell device are investigated.
In detail, porphine molecules adsorbed on Ag surfaces are observed to couple covalently when
heated on the surface. For free-base porphines two approaches are employed. In the first one
the molecules are annealed after the deposition of one ML onto the surface. Since this approach
is limited by the considerable desorption rate of 2H-P at the temperature required to induce the
dehydrogenation and coupling reactions, the second approach counteracts the desorption by the
continuous deposition of molecules while the surface is heated. With this, covalent oligomers
consisting of up to 90 units are formed. Similar to porphine tapes synthesized in solution, here
a reduction of the band gap is measured for the triply-fused dimer, representing the most abun-
dant binding motif.
Covalent homocoupling is also observed for Co-porphines. Due to the low desorption rate anneal-
ing a sub-ML is sufficient to induce the coupling. In contrast to 2H-P, Co-P exhibits a different
preferred binding motif. Furthermore, 2H-P oligomers can be metalated with Co which enables
to influence the shape of the Co-P-oligomers. In order to achieve a more directed growth of the
oligomers, the porphines are substituted with Br atoms at two meso positions. At RT deposi-
tion Ag-coordinated chains are formed, whereas at higher annealing temperatures the molecules
covalently couple, but less efficiently than for 2H-P and the Br as a byproduct remains on the
surface. Consequently, the homocoupling of unsubstituted 2H-P is a clean approach to form
covalent nanostructures on Ag surfaces with coupling motifs that had only been realized in so-
lution before.
Blocking the four reactive meso positions of 2H-P by the attachment of phenyl moieties affords
2H-TPP. For this molecule intramolecular ring-closing reactions are observed on the Ag(111)
surface. Upon annealing the phenyl rings react with the macrocycle in such a way that four
different planar porphyrin derivatives are formed, whereas one product is clearly favored over
the others. DFT calculations point to an influence of the symmetry of the molecular core on the
reaction outcome. Indeed, annealing experiments with Ru-TPP and Co-TPP, molecules with a
four-fold symmetric core opposed to the two-fold symmetric core of 2H-TPP, yield a more uni-
form distribution of the reaction products. Thus, by decreasing the symmetry of the core from
four-fold (Ru-TPP and Co-TPP) to two-fold (2H-TPP) the selectivity of the reaction outcome
102 8 CONCLUSION AND PERSPECTIVES
is increased.
If only two meso positions of a porphyrin are blocked by phenyl moieties, as for the DPP
molecule, two processes occur upon annealing. At moderate annealing temperatures, the phenyl
rings react with the macrocycle in a similar way as for 2H-TPP. These planar DPP derivatives
covalently couple at elevated annealing temperatures, similar to 2H-P. However, more binding
motifs than for 2H-P are observed.
The interaction between the substrate and the adsorbed molecule is studied for a related
molecule, the Fe-phthalocyanine. Upon adsorption on the Cu(111) surface FePcs show a two-
fold symmetry in STM images despite their four-fold symmetric gas phase configuration. This
symmetry reduction is attributed to an asymmetric charge transfer from the substrate to the
molecule which probably also causes a bending of the molecule. Thus, the main contribution
is found to be an electronic effect and in the STM images a small geometric contribution is
observed as well.
Another outcome of the interaction between substrate and molecules is its impact on the reac-
tivity of the molecules. For two different metallo-porphyrins a profound change of the affinity
of the metal center towards gas molecules is observed upon adsorption on the Ag(111) surface.
Fe-TPP molecules can ligate CO or oxygen molecules with either one or two gas molecules per
Fe-TPP. The two gases exhibit a similar geometry when adsorbed on the porphyrin, however,
in STM images they can be differentiated. In contrast to the binding ability in the protein
hemoglobin, the Ag sample has to be cooled to 20 K or lower to achieve a sufficient sticking
coefficient of CO and oxygen. Due to the strong interaction of the Fe ion with the substrate
its binding affinity to the gases is reduced. Consequently, the different chemical environments
of the protein and the metal surface significantly influence the binding affinity of Fe-porphyrin
to CO and molecular oxygen. On the other hand, Ti-TPP adsorbed on the Ag(111) surface is
oxidized at RT upon exposure to molecular oxygen. Three Oxo-Ti-TPP species are identified
by STM which represent different configurations of the same species. With this, Ti-TPP fits
into a trend across the periodic system from the unreactive Ru-porphyrin over Mn-porphyrin to
Ti-porphyrin as the most reactive molecule.
At last, the interfacial interaction of two different molecules is studied. On the Ag(111) surface
a model system of a bimolecular organic solar cell is realized with C60 as the acceptor and BO-
ADPM as the donor. When co-deposited onto the surface the two molecular species separate
from each other. Only for low deposition temperatures the molecules are immobilized so that
BO-ADPM on top of a C60 island can be imaged and the electronic band gap is measured. Thus,
the phase separation of the two molecules at the interface is likely to lower the efficiency of the
device due to an inefficient charge transfer.
Future experiments could aim to optimize the growth protocols for covalent nanostructures. The
goal is to form extended and regular-shaped structures consisting of functional molecules. The
103
clean coupling of porphyrins on Ag surfaces described in this work shows that porphyrins are
promising candidates for the on-surface bottom-up formation of covalent structures. In order
to achieve a more directed growth of the porphyrin oligomers the parameters that influence the
outcome of the reactions need to be investigated further. In detail, the influence of the coverage
of molecules, the molecular flux and the reaction duration could be studied. Moreover, the
suitability of different substrates could be tested. The physical and chemical properties of the
nanostructures can further be tuned by the employment of various substituents at the macro-
cycle and metal ions in the core of the molecule.
Furthermore, AFM measurements with a functionalized tip could help to identify reaction prod-
ucts as e.g. the planar porphyrin derivatives, different oligomers or the partially decomposed
FePcs.
Additionally, in future experiments the ligation of gaseous molecules to biologically relevant
molecules as Fe-porphyrins could be studied on different substrates in order to test the influence
of the chemical environment of the porphyrin on the binding affinity. By employing different
metal centers, the reactivity towards oxygen can be tuned.
Finally, it could be studied how the magnetic properties of metallo-porphyrins change upon the
formation of covalent oligomers and upon the ligation of small gas molecules.
104 8 CONCLUSION AND PERSPECTIVES
105
List of publications
K. Diller, F. Klappenberger, F. Allegretti, A. C. Papageorgiou, S. Fischer, A. Wiengarten, S.
Joshi, K. Seufert, D. Ecija, W. Auwarter, and J. V. Barth. “Investigating the molecule-substrate
interaction of prototypic tetrapyrrole compounds: Adsorption and self-metalation of porphine
on Cu(111).“ J. Chem. Phys., vol. 138, pp. 154710-1–154710-9, 2013.
A. C. Papageorgiou, S. Fischer, S. C. Oh, O. Saglam, J. Reichert, A. Wiengarten, K. Seufert,
S. Vijayaraghavan, D. Ecija, W. Auwarter, F. Allegretti, R. G. Acres, K. C. Prince, K. Diller,
F. Klappenberger and J. V. Barth. “Self-Terminating Protocol for an Interfacial Complexation
Reaction in Vacuo by Metal-Organic Chemical Vapor Deposition.“ ACS Nano, vol. 7, pp. 4520–
4526, 2013.
A. Wiengarten, K. Seufert, W. Auwarter, D. Ecija, K. Diller, F. Allegretti, F. Bischoff, S.
Fischer, D. A. Duncan, A. C. Papageorgiou, F. Klappenberger, R. G. Acres, T. H. Ngo and
J. V. Barth. “Surface-assisted Dehydrogenative Homocoupling of Porphine Molecules.“ J. Am.
Chem. Soc., vol. 136, pp. 9346–9354, 2014.
D. A. Duncan, P. S. Deimel, A. Wiengarten, R. Han, R. G. Acres, W. Auwarter, P. Feulner, A.
C. Papageorgiou, F. Allegretti, and J. V. Barth. “Immobilised molecular catalysts and the role
of the supporting metal substrate.“ Chem. Commun., vol. 51, pp. 9483–9486, 2015.
A. Wiengarten, J. A. Lloyd, K. Seufert, J. Reichert, W. Auwarter, R. Han, D. A. Duncan,
F. Allegretti, S. Fischer, S. C. Oh, O. Saglam, L. Jiang, S. Vijayaraghavan, D. Ecija, A. C.
Papageorgiou and J. V. Barth. “Surface-Assisted Cyclodehydrogenation; Break the Symmetry,
Enhance the Selectivity.“ accepted by Chem. Eur. J.
O. Snezhkova, J. Luder, A. Wiengarten, S. R. Burema, F. Bischoff, Y. He, J. Rusz, J. Knudsen,
M.-L. Bocquet, K. Seufert, J. V. Barth, W. Auwarter, B. Brena, and J. Schnadt. “On the Nature
of the Bias-Dependent Symmetry Reduction of Iron Phthalocyanine on Cu(111).“ accepted by
Phys. Rev. B
REFERENCES 107
References
[1] I. Langmuir, “The adsorption of gases on plane surfaces of glass, mica and platinum.,” J.
Am. Chem. Soc., vol. 40, pp. 1361–1403, 1918.
[2] The official website of the Nobel Prize, http://www.nobelprize.org/nobel prizes/physics/
laureates/1921/.
[3] C. Davisson and L. Germer, “Diffraction of electrons by a nickel crystal,” Phys. Rev.,
vol. 30, pp. 705–740, 1927.
[4] A. Zangwill, Physics at Surfaces. Cambridge University Press, 1988.
[5] G. Binnig, H. Rohrer, C. Gerber, and E. Weibel, “Surface studies by scanning tunneling
microscopy,” Phys. Rev. Lett., vol. 49, pp. 57–61, 1982.
[6] G. Binnig, C. F. Quate, and C. Gerber, “Atomic force microscope,” Phys. Rev. Lett.,
vol. 56, pp. 930–933, 1986.
[7] H. Luth, Surfaces and Interfaces of Solids. Springer-Verlag, 1993.
[8] K. Oura, V. Lifshits, A. Saranin, A. Zotov, and M. Katayama, Surface Science - An
Introduction. Springer, 2010.
[9] R. Feynman, “There’s plenty of room at the bottom [data storage],” J. Microelectromech.
S., vol. 1, pp. 60–66, 1992.
[10] W. Auwarter, D. Ecija, F. Klappenberger, and J. V. Barth, “Porphyrins at interfaces,”
Nat. Chem., vol. 7, pp. 105–120, 2015.
[11] J. T. Groves, “The bioinorganic chemistry of iron in oxygenases and supramolecular as-
semblies,” P. Natl. Acad. Sci., vol. 100, pp. 3569–3574, 2003.
[12] W. Kuhlbrandt, D. N. Wang, and Y. Fujiyoshi, “Atomic model of plant light-harvesting
complex by electron crystallography,” Nature, vol. 367, pp. 614–621, 1994.
[13] C. D. Natale, D. Salimbeni, R. Paolesse, A. Macagnano, and A. D’Amico, “Porphyrins-
based opto-electronic nose for volatile compounds detection,” Sensor. Actuat. B-Chem.,
vol. 65, pp. 220–226, 2000.
[14] N. A. Rakow and K. S. Suslick, “A colorimetric sensor array for odour visualization,”
Nature, vol. 406, pp. 710–713, 2000.
[15] A.-M. Andringa, M.-J. Spijkman, E. C. Smits, S. G. Mathijssen, P. A. van Hal, S. Setayesh,
N. P. Willard, O. V. Borshchev, S. A. Ponomarenko, P. W. Blom, and D. M. de Leeuw,
108 REFERENCES
“Gas sensing with self-assembled monolayer field-effect transistors,” Org. Electron., vol. 11,
pp. 895–898, 2010.
[16] M. R. Wasielewski, “Photoinduced electron transfer in supramolecular systems for artificial
photosynthesis,” Chem. Rev., vol. 92, pp. 435–461, 1992.
[17] A. Yella, H.-W. Lee, H. N. Tsao, C. Yi, A. K. Chandiran, M. Nazeeruddin, E. W.-G.
Diau, C.-Y. Yeh, S. M. Zakeeruddin, and M. Gratzel, “Porphyrin-sensitized solar cells
with cobalt (II/III)-based redox electrolyte exceed 12 percent efficiency,” Science, vol. 334,
pp. 629–634, 2011.
[18] B. Li, J. Li, Y. Fu, and Z. Bo, “Porphyrins with four monodisperse oligofluorene arms as
efficient red light-emitting materials,” J. Am. Chem. Soc., vol. 126, pp. 3430–3431, 2004.
[19] T. J. Dougherty, C. J. Gomer, B. W. Henderson, G. Jori, D. Kessel, M. Korbelik, J. Moan,
and Q. Peng, “Photodynamic therapy,” J. Natl. Cancer I., vol. 90, pp. 889–905, 1998.
[20] B. Meunier, “Metalloporphyrins as versatile catalysts for oxidation reactions and oxidative
DNA cleavage,” Chem. Rev., vol. 92, pp. 1411–1456, 1992.
[21] S. Yoshimoto, A. Tada, K. Suto, R. Narita, and K. Itaya, “Adlayer structure and elec-
trochemical reduction of O2 on self-organized arrays of cobalt and copper tetraphenyl
porphines on a Au(111) surface,” Langmuir, vol. 19, pp. 672–677, 2003.
[22] C. Joachim, J. K. Gimzewski, and A. Aviram, “Electronics using hybrid-molecular and
mono-molecular devices,” Nature, vol. 408, pp. 541–548, 2000.
[23] W. Auwarter, K. Seufert, F. Bischoff, D. Ecija, S. Vijayaraghavan, S. Joshi, F. Klap-
penberger, N. Samudrala, and J. V. Barth, “A surface-anchored molecular four-level con-
ductance switch based on single proton transfer,” Nat. Nanotechnol., vol. 7, pp. 41–46,
2012.
[24] N. R. Champness, “Surface chemistry: Making the right connections,” Nat. Chem., vol. 4,
pp. 149–150, 2012.
[25] G. Franc and A. Gourdon, “Covalent networks through on-surface chemistry in ultra-high
vacuum: state-of-the-art and recent developments,” Phys. Chem. Chem. Phys., vol. 13,
pp. 14283–14292, 2011.
[26] J. Mendez, M. F. Lopez, and J. A. Martın-Gago, “On-surface synthesis of cyclic organic
molecules,” Chem. Soc. Rev., vol. 40, pp. 4578–4590, 2011.
[27] M. Bieri, S. Blankenburg, M. Kivala, C. A. Pignedoli, P. Ruffieux, K. Mullen, and R. Fasel,
“Surface-supported 2D heterotriangulene polymers,” Chem. Commun., vol. 47, pp. 10239–
10241, 2011.
REFERENCES 109
[28] J. Bjork and F. Hanke, “Towards design rules for covalent nanostructures on metal sur-
faces,” Chem. Europ. J., vol. 20, pp. 928–934, 2014.
[29] W. Auwarter, F. Klappenberger, A. Weber-Bargioni, A. Schiffrin, T. Strunskus, C. Woll,
Y. Pennec, A. Riemann, and J. V. Barth, “Conformational adaptation and selective
adatom capturing of tetrapyridyl-porphyrin molecules on a copper (111) surface,” J. Am.
Chem. Soc., vol. 129, pp. 11279–11285, 2007.
[30] O. Snezhkova, J. Luder, A. Wiengarten, S. R. Burema, F. Bischoff, Y. He, J. Rusz,
J. Knudsen, M.-L. Bocquet, K. Seufert, J. V. Barth, W. Auwarter, B. Brena, and
J. Schnadt, “On the nature of the bias-dependent symmetry reduction of iron phthalocya-
nine on Cu(111),” accepted by Phys. Rev. B.
[31] A. Weber-Bargioni, W. Auwarter, F. Klappenberger, J. Reichert, S. Lefrancois, T. Strun-
skus, C. Woll, A. Schiffrin, Y. Pennec, and J. V. Barth, “Visualizing the frontier orbitals
of a conformationally adapted metalloporphyrin,” Chem. Phys. Chem., vol. 9, pp. 89–94,
2008.
[32] A. Scheybal, T. Ramsvik, R. Bertschinger, M. Putero, F. Nolting, and T. Jung, “Induced
magnetic ordering in a molecular monolayer,” Chem. Phys. Lett., vol. 411, pp. 214–220,
2005.
[33] H. Wende, M. Bernien, J. Luo, C. Sorg, N. Ponpandian, J. Kurde, J. Miguel, M. Pi-
antek, X. Xu, P. Eckhold, W. Kuch, K. Baberschke, P. M. Panchmatia, B. Sanyal, P. M.
Oppeneer, and O. Eriksson, “Substrate-induced magnetic ordering and switching of iron
porphyrin molecules,” Nat. Mater., vol. 6, pp. 516–520, 2007.
[34] F. Sedona, M. Di Marino, D. Forrer, A. Vittadini, M. Casarin, A. Cossaro, L. Flore-
ano, A. Verdini, and M. Sambi, “Tuning the catalytic activity of Ag(110)-supported Fe
phthalocyanine in the oxygen reduction reaction,” Nat. Mater., vol. 11, pp. 970–977, 2012.
[35] K. Seufert, M.-L. Bocquet, W. Auwarter, A. Weber-Bargioni, J. Reichert, N. Lorente,
and J. V. Barth, “Cis-dicarbonyl binding at cobalt and iron porphyrins with saddle-shape
conformation,” Nat. Chem., vol. 3, pp. 114–119, 2011.
[36] D. A. Duncan, P. S. Deimel, A. Wiengarten, R. Han, R. G. Acres, W. Auwarter, P. Feulner,
A. C. Papageorgiou, F. Allegretti, and J. V. Barth, “Immobilised molecular catalysts and
the role of the supporting metal substrate,” Chem. Commun., vol. 51, pp. 9483–9486,
2015.
[37] G. Binnig, H. Rohrer, C. Gerber, and E. Weibel, “Tunneling through a controllable vacuum
gap,” Appl. Phys. Lett., vol. 40, pp. 178–180, 1982.
110 REFERENCES
[38] G. Binnig, H. Rohrer, C. Gerber, and E. Weibel, “7 x 7 reconstruction on Si(111) resolved
in real space,” Phys. Rev. Lett., vol. 50, pp. 120–123, 1983.
[39] The official website of the Nobel Prize, http://www.nobelprize.org/nobel prizes/physics/
laureates/1986/.
[40] J. V. Barth, “Molecular architectonic on metal surfaces,” Annu. Rev. Phys. Chem., vol. 58,
pp. 375–407, 2007.
[41] J. Repp, G. Meyer, S. M. Stojkovic, A. Gourdon, and C. Joachim, “Molecules on insulating
films: Scanning-tunneling microscopy imaging of individual molecular orbitals,” Phys. Rev.
Lett., vol. 94, pp. 026803–1–026803–4, 2005.
[42] R. Wiesendanger, H.-J. Guntherodt, G. Guntherodt, R. J. Gambino, and R. Ruf, “Ob-
servation of vacuum tunneling of spin-polarized electrons with the scanning tunneling
microscope,” Phys. Rev. Lett., vol. 65, pp. 247–250, 1990.
[43] J. Bardeen, “Tunnelling from a many-particle point of view,” Phys. Rev. Lett., vol. 6,
pp. 57–59, 1961.
[44] J. Tersoff and D. R. Hamann, “Theory and application for the scanning tunneling micro-
scope,” Phys. Rev. Lett., vol. 50, pp. 1998–2001, 1983.
[45] J. Tersoff and D. R. Hamann, “Theory of the scanning tunneling microscope,” Phys. Rev.
B, vol. 31, pp. 805–813, 1985.
[46] R. Wiesendanger and H. Guntherodt, eds., Scanning Tunneling Microscopy III. Springer
Verlag, 1993.
[47] C. J. Chen, Introduction to Scanning Tunneling Microscopy. Oxford Science Publications,
2008.
[48] A. Selloni, P. Carnevali, E. Tosatti, and C. D. Chen, “Voltage-dependent scanning-
tunneling microscopy of a crystal surface: Graphite,” Phys. Rev. B, vol. 31, pp. 2602–2605,
1985.
[49] G. Binnig, K. H. Frank, H. Fuchs, N. Garcia, B. Reihl, H. Rohrer, F. Salvan, and A. R.
Williams, “Tunneling spectroscopy and inverse photoemission: Image and field states,”
Phys. Rev. Lett., vol. 55, pp. 991–994, 1985.
[50] R. J. Hamers, R. M. Tromp, and J. E. Demuth, “Surface electronic structure of Si (111)-(7
x 7) resolved in real space,” Phys. Rev. Lett., vol. 56, pp. 1972–1975, 1986.
[51] J. A. Stroscio, R. M. Feenstra, and A. P. Fein, “Electronic structure of the Si(111) 2 x 1
surface by scanning-tunneling microscopy,” Phys. Rev. Lett., vol. 57, pp. 2579–2582, 1986.
REFERENCES 111
[52] M. Valden, X. Lai, and D. W. Goodman, “Onset of catalytic activity of gold clusters on
titania with the appearance of nonmetallic properties,” Science, vol. 281, pp. 1647–1650,
1998.
[53] R. Hamers and D. Padowitz, Scanning Probe Microscopy and Spectroscopy. Wiley-VCH,
2001.
[54] R. Feenstra, J. A. Stroscio, and A. Fein, “Tunneling spectroscopy of the Si(111) 2 x 1
surface,” Surf. Sci., vol. 181, pp. 295–306, 1987.
[55] C. Bai, Scanning Tunneling Microscopy and its Application. Springer, 1995.
[56] R. Wiesendanger and H. Guntherodt, eds., Scanning Tunneling Microscopy I. Springer
Verlag, 1992.
[57] A. Bryant, D. P. E. Smith, and C. F. Quate, “Imaging in real time with the tunneling
microscope,” Appl. Phys. Lett., vol. 48, pp. 832–834, 1986.
[58] G. Meyer, “A simple low-temperature ultrahigh-vacuum scanning tunneling microscope
capable of atomic manipulation,” Rev. Sci. Instrum., vol. 67, pp. 2960–2965, 1996.
[59] S. Zophel, Der Aufbau eines Tieftemperatur-Rastertunnelmikroskops und Strukturunter-
suchungen auf vicinalen Kupferoberflachen. PhD thesis, Freie Universitat Berlin, 2000.
[60] CreaTec Fischer & Co. GmbH, Industriestr. 9, 74391 Erligheim, www.createc.de.
[61] H. Ibach, Physics of Surfaces and Interfaces. Springer, 2006.
[62] K. Seufert, Nanochemistry with porphyrins - a 2D perspective. PhD thesis, Technical
University of Munich, 2011.
[63] Pfeiffer Vacuum GmbH, Berliner Strasse 43, 35614 Asslar, http://www.pfeiffer-
vacuum.com/.
[64] Oerlikon Leybold Vacuum GmbH, Bonner Str. 498, 50968 Koln,
www.oerlikon.com/leyboldvacuum/de.
[65] SI Scientific Instruments GmbH, Romerstr. 67, 82205 Gilching bei Munchen, www.si-
gmbh.de.
[66] K. Besocke, “An easily operable scanning tunneling microscope,” Surf. Sci., vol. 181,
pp. 145–153, 1987.
[67] S. D. Kevan and R. H. Gaylord, “High-resolution photoemission study of the electronic
structure of the noble-metal (111) surfaces,” Phys. Rev. B, vol. 36, pp. 5809–5818, 1987.
112 REFERENCES
[68] M. F. Crommie, C. P. Lutz, and D. M. Eigler, “Imaging standing waves in a two-
dimensional electron gas,” Nature, vol. 363, pp. 524–527, 1993.
[69] S. Zophel, “How to assemble a metal sample holder (manual for the createc LT-STM).,”
[70] W. Auwarter, T. Kreutz, T. Greber, and J. Osterwalder, “XPD and STM investigation of
hexagonal boron nitride on Ni(111),” Surf. Sci., vol. 429, pp. 229–236, 1999.
[71] S. Joshi, D. Ecija, R. Koitz, M. Iannuzzi, A. P. Seitsonen, J. Hutter, H. Sachdev, S. Vi-
jayaraghavan, F. Bischoff, K. Seufert, J. V. Barth, and W. Auwarter, “Boron nitride on
Cu(111): An electronically corrugated monolayer,” Nano Lett., vol. 12, pp. 5821–5828,
2012.
[72] S. Y. Leblebici, L. Catane, D. E. Barclay, T. Olson, T. L. Chen, and B. Ma, “Near-
infrared azadipyrromethenes as electron donor for efficient planar heterojunction organic
solar cells,” Appl. Mater. Interfaces, vol. 3, pp. 4469–4474, 2011.
[73] J. Stohr, NEXAFS Spectroscopy. Springer Verlag, 1992.
[74] G. Hahner, “Near edge X-ray absorption fine structure spectroscopy as a tool to probe
electronic and structural properties of thin organic films and liquids,” Chem. Soc. Rev.,
vol. 35, pp. 1244–1255, 2006.
[75] J. Haase, “SEXAFS und NEXAFS. Rontgen-Absorptionsspektroskopie an Adsorbat-
bedeckten Oberflachen,” Chemie in unserer Zeit, vol. 26, pp. 219–231, 1992.
[76] S. Hufner, Photoelectron Spectroscopy, Principles and Applications. Springer, 2003.
[77] H. Hertz, “Uber einen Einfluss des ultravioletten Lichtes auf die elektrische Entladung,”
Ann. Physik, vol. 31, p. 983, 1887.
[78] P. Feulner and D. Menzel, “Simple ways to improve flash desorption measurements from
single crystal surfaces,” J. Vac. Sci. Technol., vol. 17, pp. 662–663, 1980.
[79] HyperChem(TM), Hypercube. Inc., 1115 NW 4th Street, Gainesville, Florida 32601, USA.
[80] K. Hermann and L. G. M. Pettersson StoBe software V. 3.0, deMon developers group,
2007, http://www.fhi-berlin.mpg.de/KHsoftware/StoBe/.
[81] J. P. Perdew, K. Burke, and M. Ernzerhof, “Generalized gradient approximation made
simple,” Phys. Rev. Lett., vol. 77, pp. 3865–3868, 1996.
[82] B. Hammer, L. B. Hansen, and J. K. Norskov, “Improved adsorption energetics within
density-functional theory using revised Perdew-Burke-Ernzerhof functionals,” Phys. Rev.
B, vol. 59, pp. 7413–7421, 1999.
REFERENCES 113
[83] J. Cai, P. Ruffieux, R. Jaafar, M. Bieri, T. Braun, S. Blankenburg, M. Muoth, A. P.
Seitsonen, M. Saleh, X. Feng, K. Mullen, and R. Fasel, “Atomically precise bottom-up
fabrication of graphene nanoribbons,” Nature, vol. 466, pp. 470–473, 2010.
[84] J. D. Zimmerman, V. V. Diev, K. Hanson, R. R. Lunt, E. K. Yu, M. E. Thompson, and
S. R. Forrest, “Porphyrin-tape/C60 organic photodetectors with 6.5% external quantum
efficiency in the near infrared,” Adv. Mater., vol. 22, pp. 2780–2783, 2010.
[85] J. D. Biggs, Y. Zhang, D. Healion, and S. Mukamel, “Watching energy transfer in met-
alloporphyrin heterodimers using stimulated X-ray Raman spectroscopy,” P. Natl. Acad.
Sci., vol. 110, pp. 15597–15601, 2013.
[86] L. Grill, M. Dyer, L. Lafferentz, M. Persson, M. V. Peters, and S. Hecht, “Nano-
architectures by covalent assembly of molecular building blocks,” Nat. Nanotechnol., vol. 2,
pp. 687–691, Nov. 2007.
[87] T. Lin, X. S. Shang, J. Adisoejoso, P. N. Liu, and N. Lin, “Steering on-surface poly-
merization with metal-directed template,” J. Am. Chem. Soc., vol. 135, pp. 3576–3582,
2013.
[88] T. A. Jung, R. R. Schlittler, and J. K. Gimzewski, “Conformational identification of
individual adsorbed molecules with the STM,” Nature, vol. 386, pp. 696–698, 1997.
[89] W. Auwarter, A. Weber-Bargioni, S. Brink, A. Riemann, A. Schiffrin, M. Ruben, and J. V.
Barth, “Controlled metalation of self-assembled porphyrin nanoarrays in two dimensions,”
Chem. Phys. Chem., vol. 8, pp. 250–254, 2007.
[90] W. Auwarter, K. Seufert, F. Klappenberger, J. Reichert, A. Weber-Bargioni, A. Verdini,
D. Cvetko, M. Dell´Angela, L. Floreano, A. Cossaro, G. Bavdek, A. Morgante, A. P.
Seitsonen, and J. V. Barth, “Site-specific electronic and geometric interface structure
of Co-tetraphenyl-porphyrin layers on Ag(111),” Phys. Rev. B, vol. 81, pp. 245403–1 –
245403–14, 2010.
[91] S. Mohnani and D. Bonifazi, “Supramolecular architectures of porphyrins on surfaces:
The structural evolution from 1D to 2D to 3D to devices,” Coord. Chem. Rev., vol. 254,
pp. 2342–2362, 2010.
[92] A. Osuka and H. Shimidzu, “Meso, meso-linked porphyrin arrays,” Angew. Chem. Int.
Ed., vol. 36, pp. 135–137, 1997.
[93] A. Tsuda and A. Osuka, “Fully conjugated porphyrin tapes with electronic absorption
bands that reach into infrared,” Science, vol. 293, pp. 79–82, 2001.
114 REFERENCES
[94] H. S. Cho, D. H. Jeong, S. Cho, D. Kim, Y. Matsuzaki, K. Tanaka, A. Tsuda, and
A. Osuka, “Photophysical properties of porphyrin tapes,” J. Am. Chem. Soc., vol. 124,
pp. 14642–14654, 2002.
[95] A. A. Ryan and M. O. Senge, “Synthesis and functionalization of triply fused porphyrin
dimers,” Europ. J. Org. Chem., vol. 2013, pp. 3700–3711, 2013.
[96] D. F. Perepichka and M. R. Bryce, “Molecules with exceptionally small HOMO-LUMO
gaps,” Angew. Chem. Int. Ed., vol. 44, pp. 5370–5373, 2005.
[97] D. Y. Kim, T. K. Ahn, J. H. Kwon, D. Kim, T. Ikeue, N. Aratani, A. Osuka, M. Shigeiwa,
and S. Maeda, “Large two-photon absorption (TPA) cross-section of directly linked fused
diporphyrins,” J. Phys. Chem. A, vol. 109, pp. 2996–2999, 2005.
[98] E. Y. Li and N. Marzari, “Conductance switching and many-valued logic in porphyrin
assemblies,” J. Phys. Chem. Lett., vol. 4, pp. 3039–3044, 2013.
[99] N. Hauptmann, C. Hamann, H. Tang, and R. Berndt, “Soft-landing electrospray deposition
of the ruthenium dye N3 on Au(111),” J. Phys. Chem. C, vol. 117, pp. 9734–9738, 2013.
[100] M. Pauly, M. Sroka, J. Reiss, G. Rinke, A. Albarghash, R. Vogelgesang, H. Hahne,
B. Kuster, J. Sesterhenn, K. Kern, and S. Rauschenbach, “A hydrodynamically optimized
nano-electrospray ionization source and vacuum interface,” Analyst, vol. 139, pp. 1856–
1867, 2014.
[101] M. I. Veld, P. Iavicoli, S. Haq, D. B. Amabilino, and R. Raval, “Unique intermolecular
reaction of simple porphyrins at a metal surface gives covalent nanostructures,” Chem.
Commun., pp. 1536–1538, 2008.
[102] L. Lafferentz, V. Eberhardt, C. Dri, C. Africh, G. Comelli, F. Esch, S. Hecht, and L. Grill,
“Controlling on-surface polymerization by hierarchical and substrate-directed growth,”
Nat. Chem., vol. 4, pp. 215–220, 2012.
[103] M. S. Dyer, A. Robin, S. Haq, R. Raval, M. Persson, and J. Klimes, “Understanding the
interaction of the porphyrin macrocycle to reactive metal substrates: Structure, bonding,
and adatom capture,” ACS Nano, vol. 5, pp. 1831–1838, 2011.
[104] F. Bischoff, K. Seufert, W. Auwarter, S. Joshi, S. Vijayaraghavan, D. Ecija, K. Diller,
A. C. Papageorgiou, S. Fischer, F. Allegretti, D. A. Duncan, F. Klappenberger, F. Blobner,
R. Han, and J. V. Barth, “How surface bonding and repulsive interactions cause phase
transformations: Ordering of a prototype macrocyclic compound on Ag(111),” ACS Nano,
vol. 7, pp. 3139–3149, 2013.
REFERENCES 115
[105] K. Diller, F. Klappenberger, F. Allegretti, A. C. Papageorgiou, S. Fischer, A. Wien-
garten, S. Joshi, K. Seufert, D. Ecija, W. Auwarter, and J. V. Barth, “Investigating the
molecule-substrate interaction of prototypic tetrapyrrole compounds: Adsorption and self-
metalation of porphine on Cu(111),” J. Chem. Phys., vol. 138, pp. 154710–1–154710–9,
2013.
[106] J. M. Gottfried, K. Flechtner, A. Kretschmann, T. Lukasczyk, and H.-P. Steinruck, “Direct
synthesis of a metalloporphyrin complex on a surface,” J. Am. Chem. Soc., vol. 128,
pp. 5644–5645, 2006.
[107] F. Buchner, K. Flechtner, Y. Bai, E. Zillner, I. Kellner, H.-P. Steinruck, H. Marbach, and
J. M. Gottfried, “Coordination of iron atoms by tetraphenylporphyrin monolayers and
multilayers on Ag(111) and formation of iron-tetraphenylporphyrin,” J. Phys. Chem. C,
vol. 112, pp. 15458–15465, 2008.
[108] A. C. Papageorgiou, S. Fischer, S. C. Oh, O. Saglam, J. Reichert, A. Wiengarten,
K. Seufert, S. Vijayaraghavan, D. Ecija, W. Auwarter, F. Allegretti, R. G. Acres, K. C.
Prince, K. Diller, F. Klappenberger, and J. V. Barth, “Self-terminating protocol for an
interfacial complexation reaction in vacuo by metal-organic chemical vapor deposition,”
ACS Nano, vol. 7, pp. 4520–4526, 2013.
[109] M. Lackinger and W. M. Heckl, “A STM perspective on covalent intermolecular coupling
reactions on surfaces,” J. Phys. D: Appl. Phys., vol. 44, p. 464011, 2011.
[110] J. Eichhorn, D. Nieckarz, O. Ochs, D. Samanta, M. Schmittel, P. J. Szabelski, and
M. Lackinger, “On-surface Ullmann coupling: The influence of kinetic reaction parameters
on the morphology and quality of covalent networks,” ACS Nano, vol. 8, pp. 7880–7889,
2014.
[111] A. Wiengarten, K. Seufert, W. Auwarter, D. Ecija, K. Diller, F. Allegretti, F. Bischoff,
S. Fischer, D. A. Duncan, A. C. Papageorgiou, F. Klappenberger, R. G. Acres, T. H. Ngo,
and J. V. Barth, “Surface-assisted dehydrogenative homocoupling of porphine molecules,”
J. Am. Chem. Soc., vol. 136, pp. 9346–9354, 2014.
[112] S. Haq, F. Hanke, M. S. Dyer, M. Persson, P. Iavicoli, D. B. Amabilino, and R. Raval,
“Clean coupling of unfunctionalized porphyrins at surfaces to give highly oriented
organometallic oligomers,” J. Am. Chem. Soc., vol. 133, pp. 12031–12039, 2011.
[113] Y. Nakamura, N. Aratani, H. Shinokubo, A. Takagi, T. Kawai, T. Matsumoto, Z. S. Yoon,
D. Y. Kim, T. K. Ahn, D. Kim, A. Muranaka, N. Kobayashi, and A. Osuka, “A directly
fused tetrameric porphyrin sheet and its anomalous electronic properties that arise from
the planar cyclooctatetraene core,” J. Am. Chem. Soc., vol. 128, pp. 4119–4127, 2006.
116 REFERENCES
[114] Y.-Q. Zhang, N. Kepcija, M. Kleinschrodt, K. Diller, S. Fischer, A. C. Papageorgiou,
F. Allegretti, J. Bjork, S. Klyatskaya, F. Klappenberger, M. Ruben, and J. V. Barth,
“Homo-coupling of terminal alkynes on a noble metal surface,” Nat. Commun., vol. 3,
p. 1286, 2012.
[115] J. Bjork, Y.-Q. Zhang, F. Klappenberger, J. V. Barth, and S. Stafstrom, “Unraveling the
mechanism of the covalent coupling between terminal alkynes on a noble metal,” J. Phys.
Chem. C, vol. 118, pp. 3181–3187, 2014.
[116] A. Streitwieser and C. H. Heathcock, Introduction to organic chemistry. New York:
Macmillan, 1985.
[117] A. L. Pinardi, G. Otero-Irurueta, I. Palacio, J. I. Martinez, C. Sanchez-Sanchez, M. Tello,
C. Rogero, A. Cossaro, A. Preobrajenski, B. Gomez-Lor, A. Jancarik, I. G. Stara, I. Stary,
M. F. Lopez, J. Mendez, and J. A. Martin-Gago, “Tailored formation of n-doped nanoar-
chitectures by diffusion-controlled on-surface (cyclo)dehydrogenation of heteroaromatics,”
ACS Nano, vol. 7, pp. 3676–3684, 2013.
[118] T.-C. Tseng, C. Urban, Y. Wang, R. Otero, S. L. Tait, M. Alcami, D. Ecija, M. Trelka,
J. M. Gallego, N. Lin, M. Konuma, U. Starke, A. Nefedov, A. Langner, C. Woell, M. A.
Herranz, F. Martın, N. Martın, K. Kern, and R. Miranda, “Charge-transfer-induced
structural rearrangements at both sides of organic/metal interfaces,” Nat. Chem., vol. 2,
pp. 374–379, 2010.
[119] I. Dabo, A. Ferretti, C.-H. Park, N. Poilvert, Y. Li, M. Cococcioni, and N. Marzari, “Donor
and acceptor levels of organic photovoltaic compounds from first principles,” Phys. Chem.
Chem. Phys., vol. 15, pp. 685–695, 2013.
[120] Y. Yamaguchi, “Time-dependent density functional calculations of fully pi-conjugated zinc
oligoporphyrins,” J. Chem. Phys., vol. 117, pp. 9688–9694, 2002.
[121] S. S. Zade and M. Bendikov, “From oligomers to polymer: Convergence in the HOMO-
LUMO gaps of conjugated oligomers,” Org. Lett., vol. 8, pp. 5243–5246, 2006.
[122] S. S. Zade, N. Zamoshchik, and M. Bendikov, “From short conjugated oligomers to con-
jugated polymers. Lessons from studies on long conjugated oligomers,” Acc. Chem. Res.,
vol. 44, pp. 14–24, 2011.
[123] L. Cardenas, R. Gutzler, J. Lipton-Duffin, C. Fu, J. L. Brusso, L. E. Dinca, M. Vondracek,
Y. Fagot-Revurat, D. Malterre, F. Rosei, and D. F. Perepichka, “Synthesis and electronic
structure of a two dimensional pi-conjugated polythiophene,” Chem. Sci., vol. 4, pp. 3263–
3268, 2013.
REFERENCES 117
[124] W. Auwarter, A. Weber-Bargioni, A. Riemann, A. Schiffrin, O. Groning, R. Fasel, and
J. V. Barth, “Self-assembly and conformation of tetrapyridyl-porphyrin molecules on
Ag(111),” J. Chem. Phys., vol. 124, pp. 194708–1–194708–6, 2006.
[125] S.-H. Chang, S. Kuck, J. Brede, L. Lichtenstein, G. Hoffmann, and R. Wiesendan-
ger, “Symmetry reduction of metal phthalocyanines on metals,” Phys. Rev. B, vol. 78,
pp. 233409–1–233409–4, 2008.
[126] R. Cuadrado, J. I. Cerda, Y. Wang, G. Xin, R. Berndt, and H. Tang, “CoPc adsorption
on Cu(111): Origin of the C4 to C2 symmetry reduction,” J. Chem. Phys., vol. 133,
pp. 154701–1–154701–7, 2010.
[127] M. Bieri, M.-T. Nguyen, O. Groning, J. Cai, M. Treier, K. Ait-Mansour, P. Ruffieux, C. A.
Pignedoli, D. Passerone, M. Kastler, K. Mullen, and R. Fasel, “Two-dimensional polymer
formation on surfaces: Insight into the roles of precursor mobility and reactivity,” J. Am.
Chem. Soc., vol. 132, pp. 16669–16676, 2010.
[128] R. Gutzler, L. Cardenas, J. Lipton-Duffin, M. El Garah, L. E. Dinca, C. E. Szakacs, C. Fu,
M. Gallagher, M. Vondracek, M. Rybachuk, D. F. Perepichka, and F. Rosei, “Ullmann-type
coupling of brominated tetrathienoanthracene on copper and silver,” Nanoscale, vol. 6,
pp. 2660–2668, 2014.
[129] K.-H. Chung, B.-G. Koo, H. Kim, J. K. Yoon, J.-H. Kim, Y.-K. Kwon, and S.-J. Kahng,
“Electronic structures of one-dimensional metal-molecule hybrid chains studied using scan-
ning tunneling microscopy and density functional theory,” Phys. Chem. Chem. Phys.,
vol. 14, pp. 7304–7308, 2012.
[130] M. Matena, T. Riehm, M. Stohr, T. A. Jung, and L. H. Gade, “Transforming surface
coordination polymers into covalent surface polymers: Linked polycondensed aromatics
through oligomerization of n-heterocyclic carbene intermediates,” Angew. Chem. Int. Ed.,
vol. 47, pp. 2414–2417, 2008.
[131] H. Walch, R. Gutzler, T. Sirtl, G. Eder, and M. Lackinger, “Material- and orientation-
dependent reactivity for heterogeneously catalyzed carbon-bromine bond homolysis,” J.
Phys. Chem. C, vol. 114, pp. 12604–12609, 2010.
[132] F. Hanke, S. Haq, R. Raval, and M. Persson, “Heat-to-connect: Surface commensurability
directs organometallic one-dimensional self-assembly,” ACS Nano, vol. 5, pp. 9093–9103,
2011.
[133] M. Di Giovannantonio, M. El Garah, J. Lipton-Duffin, V. Meunier, L. Cardenas,
Y. Fagot Revurat, A. Cossaro, A. Verdini, D. F. Perepichka, F. Rosei, and G. Con-
tini, “Insight into organometallic intermediate and its evolution to covalent bonding in
surface-confined Ullmann polymerization,” ACS Nano, vol. 7, pp. 8190–8198, 2013.
118 REFERENCES
[134] R. Gutzler, H. Walch, G. Eder, S. Kloft, W. M. Heckl, and M. Lackinger, “Surface me-
diated synthesis of 2D covalent organic frameworks: 1,3,5-tris(4-bromophenyl)benzene on
graphite(001), Cu(111), and Ag(110),” Chem. Commun., pp. 4456–4458, 2009.
[135] J. Eichhorn, T. Strunskus, A. Rastgoo-Lahrood, D. Samanta, M. Schmittel, and
M. Lackinger, “On-surface Ullmann polymerization via intermediate organometallic net-
works on Ag(111),” Chem. Commun., vol. 50, pp. 7680–7682, 2014.
[136] M. Koch, F. Ample, C. Joachim, and L. Grill, “Voltage-dependent conductance of a single
graphene nanoribbon,” Nat. Nanotechnol., vol. 7, pp. 713–717, 2012.
[137] B. M. Trost, “Selectivity: A key to synthetic efficiency,” Science, vol. 219, pp. 245–250,
1983.
[138] G. A. Somorjai and J. Y. Park, “Molecular factors of catalytic selectivity,” Angew. Chem.
Int. Ed., vol. 47, pp. 9212–9228, 2008.
[139] P. Anastas and N. Eghbali, “Green chemistry: Principles and practice,” Chem. Soc. Rev.,
vol. 39, pp. 301–312, 2010.
[140] H.-U. Blaser, B. Pugin, and F. Spindler, “Progress in enantioselective catalysis assessed
from an industrial point of view,” J. Mol. Catal. A - Chem., vol. 231, pp. 1–20, 2005.
[141] P. Linnane, N. Magnus, and P. Magnus, “Induction of molecular asymmetry by a remote
chiral group,” Nature, vol. 385, pp. 799–801, 1997.
[142] A. Lennartson, S. Olsson, J. Sundberg, and M. Hakansson, “A different approach to enan-
tioselective organic synthesis: Absolute asymmetric synthesis of organometallic reagents,”
Angew. Chem. Int. Ed., vol. 48, pp. 3137–3140, 2009.
[143] P. Etayo and A. Vidal-Ferran, “Rhodium-catalysed asymmetric hydrogenation as a valu-
able synthetic tool for the preparation of chiral drugs,” Chem. Soc. Rev., vol. 42, pp. 728–
754, 2013.
[144] A. Warmflash, B. Sorre, F. Etoc, E. D. Siggia, and A. H. Brivanlou, “A method to recapit-
ulate early embryonic spatial patterning in human embryonic stem cells,” Nat. Methods,
vol. 11, pp. 847–854, 2014.
[145] O. I. Kolodiazhnyi, “Multiple stereoselectivity and its application in organic synthesis,”
Tetrahedron, vol. 59, pp. 5953–6018, 2003.
[146] K. Gopalaiah, “Chiral iron catalysts for asymmetric synthesis,” Chem. Rev., vol. 113,
pp. 3248–3296, 2013.
[147] M. Heitbaum, F. Glorius, and I. Escher, “Asymmetric heterogeneous catalysis,” Angew.
Chem. Int. Ed., vol. 45, pp. 4732–4762, 2006.
REFERENCES 119
[148] G. Kyriakou, S. K. Beaumont, and R. M. Lambert, “Aspects of heterogeneous enantiose-
lective catalysis by metals,” Langmuir, vol. 27, pp. 9687–9695, 2011.
[149] A. Violi, “Cyclodehydrogenation reactions to cyclopentafused polycyclic aromatic hydro-
carbons,” J. Phys. Chem. A, vol. 109, pp. 7781–7787, 2005.
[150] M. Treier, C. A. Pignedoli, T. Laino, R. Rieger, K. Mullen, D. Passerone, and R. Fasel,
“Surface-assisted cyclodehydrogenation provides a synthetic route towards easily process-
able and chemically tailored nanographenes,” Nat. Chem., vol. 3, pp. 61–67, 2011.
[151] G. DiSanto, S. Blankenburg, C. Castellarin-Cudia, M. Fanetti, P. Borghetti, L. Sangaletti,
L. Floreano, A. Verdini, E. Magnano, F. Bondino, C. A. Pignedoli, M.-T. Nguyen, R. Gas-
pari, D. Passerone, and A. Goldoni, “Supramolecular engineering through temperature-
induced chemical modification of 2H-tetraphenylporphyrin on Ag(111): Flat phenyl con-
formation and possible dehydrogenation reactions,” Chem. Europ. J., vol. 17, pp. 14354–
14359, 2011.
[152] F. Buchner, I. Kellner, W. Hieringer, A. Gorling, H.-P. Steinruck, and H. Marbach, “Or-
dering aspects and intramolecular conformation of tetraphenylporphyrins on Ag(111),”
Phys. Chem. Chem. Phys., vol. 12, pp. 13082–13090, 2010.
[153] A. Wiengarten, J. A. Lloyd, K. Seufert, J. Reichert, W. Auwarter, R. Han, D. A. Duncan,
F. Allegretti, S. Fischer, S. C. Oh, O. Saglam, L. Jiang, S. Vijayaraghavan, D. Ecija,
A. C. Papageorgiou, and J. V. Barth, “Surface-assisted cyclodehydrogenation; break the
symmetry, enhance the selectivity,” accepted by Chem. Europ. J.
[154] P. W. Atkins and J. de Paula, Elements of Physical Chemistry. Oxford: Wiley-VCH, 2013.
[155] J. Hennig and H.-H. Limbach, “Kinetic study of hydrogen tunnelling in meso-
tetraphenylporphine by nuclear magnetic resonance lineshape analysis and selective T1ρ-
relaxation time measurements,” J. Chem. Soc. Farad. T. 2, vol. 75, pp. 752–766, 1978.
[156] M. Rockert, M. Franke, Q. Tariq, S. Ditze, M. Stark, P. Uffinger, D. Wechsler, U. Singh,
J. Xiao, H. Marbach, H.-P. Steinruck, and O. Lytken, “Coverage- and temperature-
dependent metalation and dehydrogenation of tetraphenylporphyrin on Cu(111),” Chem.
Europ. J., vol. 20, pp. 8948–8953, 2014.
[157] M. Koch, Growth and Characterization of Single Molecular Wires on Metal Surfaces. PhD
thesis, Freie Universitat Berlin, 2013.
[158] K. Diller, F. Klappenberger, M. Marschall, K. Hermann, A. Nefedov, C. Woll, and J. V.
Barth, “Self-metalation of 2h-tetraphenylporphyrin on Cu(111): An x-ray spectroscopy
study,” J. Chem. Phys., vol. 136, pp. 014705–1–014705–13, 2012.
120 REFERENCES
[159] J. A. A. Elemans, R. van Hameren, R. J. M. Nolte, and A. E. Rowan, “Molecular materials
by self-assembly of porphyrins, phthalocyanines, and perylenes,” Adv. Mater., vol. 18,
pp. 1251–1266, 2006.
[160] R. Zhou, F. Josse, W. Gopel, Z. Z. Ozturk, and O. Bekaroglu, “Phthalocyanines as sensitive
materials for chemical sensors,” Appl. Organomet. Chem., vol. 10, pp. 557–577, 1996.
[161] T. Tsuzuki, Y. Shirota, J. Rostalski, and D. Meissner, “The effect of fullerene doping
on photoelectric conversion using titanyl phthalocyanine and a perylene pigment,” Sol.
Energ. Mat. Sol. C, vol. 61, pp. 1–8, 2000.
[162] C. Di, F. Zhang, and D. Zhu, “Multi-functional integration of organic field-effect transistors
(OFETs): Advances and perspectives,” Adv. Mater., vol. 25, pp. 313–330, 2013.
[163] B. W. Heinrich, C. Iacovita, T. Brumme, D.-J. Choi, L. Limot, M. V. Rastei, W. A.
Hofer, J. Kortus, and J.-P. Bucher, “Direct observation of the tunneling channels of a
chemisorbed molecule,” J. Phys. Chem. Lett., vol. 1, pp. 1517–1523, 2010.
[164] L. Gao, W. Ji, Y. B. Hu, Z. H. Cheng, Z. T. Deng, Q. Liu, N. Jiang, X. Lin, W. Guo,
S. X. Du, W. A. Hofer, X. C. Xie, and H.-J. Gao, “Site-specific Kondo effect at ambient
temperatures in iron-based molecules,” Phys. Rev. Lett., vol. 99, pp. 106402–1–106402–4,
2007.
[165] A. Mugarza, R. Robles, C. Krull, R. Korytar, N. Lorente, and P. Gambardella, “Electronic
and magnetic properties of molecule-metal interfaces: Transition-metal phthalocyanines
adsorbed on Ag(100),” Phys. Rev. B, vol. 85, pp. 155437–1–155437–13, 2012.
[166] R. Rehman, W. Dou, H. Qian, H. Mao, F. Floether, H. Zhang, H. Li, P. He, and S. Bao,
“Adsorption behavior of iron phthalocyanine at the initial stage on Cu(100) surface,” Surf.
Sci., vol. 606, pp. 1749–1754, 2012.
[167] H. Karacuban, M. Lange, J. Schaffert, O. Weingart, T. Wagner, and R. Moller, “Substrate-
induced symmetry reduction of CuPc on Cu(111): An LT-STM study,” Surf. Sci., vol. 603,
pp. L39–L43, 2009.
[168] Y. Wang, J. Kroger, R. Berndt, and W. Hofer, “Structural and electronic properties of
ultrathin tin-phthalocyanine films on Ag(111) at the single-molecule level,” Angew. Chem.
Int. Ed., vol. 48, pp. 1261–1265, 2009.
[169] J. D. Baran and J. A. Larsson, “Theoretical insights into adsorption of cobalt phthalocya-
nine on Ag(111): A combination of chemical and van der Waals bonding,” J. Phys. Chem.
C, vol. 117, pp. 23887–23898, 2013.
REFERENCES 121
[170] K. Manandhar, T. Ellis, K. Park, T. Cai, Z. Song, and J. Hrbek, “A scanning tunneling
microscopy study on the effect of post-deposition annealing of copper phthalocyanine thin
films,” Surf. Sci., vol. 601, pp. 3623–3631, 2007.
[171] A. Scarfato, S.-H. Chang, S. Kuck, J. Brede, G. Hoffmann, and R. Wiesendanger, “Scan-
ning tunneling microscope study of iron(II) phthalocyanine growth on metals and insulat-
ing surfaces,” Surf. Sci., vol. 602, pp. 677–683, 2008.
[172] M. Ziegler, N. Neel, A. Sperl, J. Kroger, and R. Berndt, “Local density of states from
constant-current tunneling spectra,” Phys. Rev. B, vol. 80, pp. 125402–1–125402–6, 2009.
[173] O. Snezhkova. Private Communication.
[174] A. Gulino, T. Gupta, P. G. Mineo, and M. E. van der Boom, “Selective NOx optical sensing
with surface-confined osmium polypyridyl complexes,” Chem. Commun., pp. 4878–4880,
2007.
[175] B. R. Takulapalli, G. M. Laws, P. A. Liddell, J. Andreasson, Z. Erno, D. Gust, and
T. J. Thornton, “Electrical detection of amine ligation to a metalloporphyrin via a hybrid
SOI-MOSFET,” J. Am. Chem. Soc., vol. 130, pp. 2226–2233, 2008.
[176] N. Ballav, C. Wackerlin, D. Siewert, P. M. Oppeneer, and T. A. Jung, “Emergence of
on-surface magnetochemistry,” J. Phys. Chem. Lett., vol. 4, pp. 2303–2311, 2013.
[177] A. Strozecka, M. Soriano, J. I. Pascual, and J. J. Palacios, “Reversible change of the spin
state in a manganese phthalocyanine by coordination of CO molecule,” Phys. Rev. Lett.,
vol. 109, p. 147202, 2012.
[178] N. Tsukahara, E. Minamitani, Y. Kim, M. Kawai, and N. Takagi, “Controlling orbital-
selective Kondo effects in a single molecule through coordination chemistry,” J. Chem.
Phys., vol. 141, pp. 054702–1–054702–9, 2014.
[179] P. Gambardella, S. Stepanow, A. Dmitriev, J. Honolka, F. M. F. de Groot, M. Lingenfelder,
S. S. Gupta, D. D. Sarma, P. Bencok, S. Stanescu, S. Clair, S. Pons, N. Lin, A. P. Seitsonen,
H. Brune, J. V. Barth, and K. Kern, “Supramolecular control of the magnetic anisotropy in
two-dimensional high-spin Fe arrays at a metal interface,” Nat. Mater., vol. 8, pp. 189–193,
2009.
[180] C. Wackerlin, D. Chylarecka, A. Kleibert, K. Muller, C. Iacovita, F. Nolting, T. A. Jung,
and N. Ballav, “Controlling spins in adsorbed molecules by a chemical switch,” Nat.
Commun., vol. 1, p. 61, 2010.
[181] C. Coperet, M. Chabanas, R. Petroff Saint-Arroman, and J.-M. Basset, “Homogeneous
and heterogeneous catalysis: Bridging the gap through surface organometallic chemistry,”
Angew. Chem. Int. Ed., vol. 42, pp. 156–181, 2003.
122 REFERENCES
[182] G. A. Somorjai, A. M. Contreras, M. Montano, and R. M. Rioux, “Clusters, surfaces, and
catalysis,” P. Natl. Acad. Sci., vol. 103, pp. 10577–10583, 2006.
[183] J. V. Barth, G. Costantini, and K. Kern, “Engineering atomic and molecular nanostruc-
tures at surfaces,” Nature, vol. 437, pp. 671–679, 2005.
[184] W. Hieringer, K. Flechtner, A. Kretschmann, K. Seufert, W. Auwarter, J. V. Barth,
A. Gorling, H.-P. Steinruck, and J. M. Gottfried, “The surface trans effect: Influence of
axial ligands on the surface chemical bonds of adsorbed metalloporphyrins,” J. Am. Chem.
Soc., vol. 133, pp. 6206–6222, 2011.
[185] B. A. Springer, S. G. Sligar, J. S. Olson, and G. N. J. Phillips, “Mechanisms of ligand
recognition in myoglobin,” Chem. Rev., vol. 94, pp. 699–714, 1994.
[186] J. T. Groves and R. Quinn, “Aerobic epoxidation of olefins with ruthenium porphyrin
catalysts,” J. Am. Chem. Soc., vol. 107, pp. 5790–5792, 1985.
[187] M. Bowker, The basis and applications of heterogeneous catalysis. Oxford University Press,
1998.
[188] F. Buchner, V. Schwald, K. Comanici, H.-P. Steinruck, and H. Marbach, “Microscopic
evidence of the metalation of a free-base porphyrin monolayer with iron,” Chem. Phys.
Chem., vol. 8, pp. 241–243, 2007.
[189] S. Joshi, F. Bischoff, R. Koitz, D. Ecija, K. Seufert, A. P. Seitsonen, J. Hutter, K. Diller,
J. I. Urgel, H. Sachdev, J. V. Barth, and W. Auwarter, “Control of molecular organization
and energy level alignment by an electronically nanopatterned boron nitride template,”
ACS Nano, vol. 8, pp. 430–442, 2014.
[190] V. D. Pham, J. Lagoute, O. Mouhoub, F. Joucken, V. Repain, C. Chacon, A. Bellec,
Y. Girard, and S. Rousset, “Electronic interaction between nitrogen-doped graphene and
porphyrin molecules,” ACS Nano, vol. 8, pp. 9403–9409, 2014.
[191] M. Palummo, C. Hogan, F. Sottile, P. Bagala, and A. Rubio, “Ab initio electronic and
optical spectra of free-base porphyrins: The role of electronic correlation,” J. Chem. Phys.,
vol. 131, pp. 084102–1–084102–7, 2009.
[192] X. Blase, C. Attaccalite, and V. Olevano, “First-principles GW calculations for fullerenes,
porphyrins, phtalocyanine, and other molecules of interest for organic photovoltaic appli-
cations,” Phys. Rev. B, vol. 83, p. 115103, 2011.
[193] J. I. Urgel, M. Schwarz, M. Garnica, D. Stassen, D. Bonifazi, D. Ecija, J. V. Barth, and
W. Auwarter, “Controlling coordination reactions and assembly on a Cu(111) supported
boron nitride monolayer,” J. Am. Chem. Soc., vol. 137, pp. 2420–2423, 2015.
REFERENCES 123
[194] K. Seufert, W. Auwarter, and J. V. Barth, “Discriminative response of surface-confined
metalloporphyrin molecules to carbon and nitrogen monoxide,” J. Am. Chem. Soc.,
vol. 132, pp. 18141–18146, 2010.
[195] M. F. Perutz, “Regulation of oxygen affinity of hemoglobin: Influence of structure of the
globin on the heme iron,” Annu. Rev. Biochem., vol. 48, pp. 327–386, 1979.
[196] H. Chen, M. Ikeda-Saito, and S. Shaik, “Nature of the Fe-O2 bonding in oxy-myoglobin:
Effect of the protein,” J. Am. Chem. Soc., vol. 130, pp. 14778–14790, 2008.
[197] D. A. Duncan. Private Communication.
[198] Y. Bai, F. Buchner, I. Kellner, M. Schmid, F. Vollnhals, H.-P. Steinruck, H. Marbach, and
J. M. Gottfried, “Adsorption of cobalt (II) octaethylporphyrin and 2H-octaethylporphyrin
on Ag(111): new insight into the surface coordinative bond,” New J. Phys., vol. 11,
p. 125004, 2009.
[199] A. Fujishima and K. Honda, “Electrochemical photolysis of water at a semiconductor
electrode,” Nature, vol. 238, pp. 37–38, 1972.
[200] A. L. Sobolewski and W. Domcke, “Photoinduced water splitting with oxotitanium por-
phyrin: a computational study,” Phys. Chem. Chem. Phys., vol. 14, pp. 12807–12817,
2012.
[201] O. Morawski, K. Izdebska, E. Karpiuk, J. Nowacki, A. Suchocki, and A. L. Sobolewski,
“Photoinduced water splitting with oxotitanium tetraphenylporphyrin,” Phys. Chem.
Chem. Phys., vol. 16, pp. 15256–15262, 2014.
[202] P. S. Deimel, “Ligation of adducts to tetrapyrrolic metal-organic complexes adsorbed on
Ag(111),” Master’s thesis, Technical University of Munich, 2014.
[203] B. E. Murphy, S. A. Krasnikov, N. N. Sergeeva, A. A. Cafolla, A. B. Preobrajenski,
A. N. Chaika, O. Lubben, and I. V. Shvets, “Homolytic cleavage of molecular oxygen by
manganese porphyrins supported on Ag(111),” ACS Nano, vol. 8, pp. 5190–5198, 2014.
[204] T. M. Clarke and J. R. Durrant, “Charge photogeneration in organic solar cells,” Chem.
Rev., vol. 110, pp. 6736–6767, 2010.
[205] R. R. Lunt and V. Bulovic, “Transparent, near-infrared organic photovoltaic solar cells
for window and energy-scavenging applications,” Appl. Phys. Lett., vol. 98, pp. 113305–
1–113305–3, 2011.
[206] H. Hoppe and N. S. Sariciftci, “Organic solar cells: An overview,” J. Mater. Res., vol. 19,
pp. 1924–1945, 2004.
124 REFERENCES
[207] M. T. Lloyd, J. E. Anthony, and G. G. Malliaras, “Photovoltaics from soluble small
molecules,” Mater. Today, vol. 10, pp. 34–41, 2007.
[208] N. Martın, L. Sanchez, B. Illescas, and I. Perez, “C60-based electroactive
organofullerenes,” Chem. Rev., vol. 98, pp. 2527–2548, 1998.
[209] A. Ojala, A. Petersen, A. Fuchs, R. Lovrincic, C. Polking, J. Trollmann, J. Hwang,
C. Lennartz, H. Reichelt, H. W. Hoffken, A. Pucci, P. Erk, T. Kirchartz, and F. Wurthner,
“Merocyanine/C60 planar heterojunction solar cells: Effect of dye orientation on exciton
dissociation and solar cell performance,” Adv. Func. Mater., vol. 22, pp. 86–96, 2012.
[210] P. Erwin and M. E. Thompson, “Elucidating the interplay between dark current coupling
and open circuit voltage in organic photovoltaics,” Appl. Phys. Lett., vol. 98, no. 22,
pp. 223305–1–223305–3, 2011.
[211] B. P. Rand, D. Cheyns, K. Vasseur, N. C. Giebink, S. Mothy, Y. Yi, V. Coropceanu,
D. Beljonne, J. Cornil, J.-L. Bredas, and J. Genoe, “The impact of molecular orientation
on the photovoltaic properties of a phthalocyanine/fullerene heterojunction,” Adv. Func.
Mater., vol. 22, pp. 2987–2995, 2012.
[212] M. Olguin, R. R. Zope, and T. Baruah, “Effect of geometrical orientation on the charge-
transfer energetics of supramolecular (tetraphenyl)-porphyrin/C60 dyads,” J. Chem. Phys.,
vol. 138, pp. 074306–1–074306–8, 2013.
[213] J. R. Tumbleston, B. A. Collins, L. Yang, A. C. Stuart, E. Gann, W. Ma, W. You, and
H. Ade, “The influence of molecular orientation on organic bulk heterojunction solar cells,”
Nat. Photonics, vol. 8, pp. 385–391, 2014.
[214] T. Sakurai, X.-D. Wang, Q. Xue, Y. Hasegawa, T. Hashizume, and H. Shinohara, “Scan-
ning tunneling microscopy study of fullerenes,” Prog. Surf. Sci., vol. 51, pp. 263–408,
1996.
[215] S. Vijayaraghavan, D. Ecija, W. Auwarter, S. Joshi, K. Seufert, A. P. Seitsonen, K. Tashiro,
and J. V. Barth, “Selective supramolecular fullerene-porphyrin interactions and switching
in surface-confined C60-Ce(TPP)2 dyads,” Nano Lett., vol. 12, pp. 4077–4083, 2012.
Acknowledgment
In the end, I would like to thank everybody who contributed to this work and supported me
during this time.
At first, I thank Prof. Dr. Johannes Barth for supervising my work and giving me the opportu-
nity to experience the inspiring atmosphere of his group. I am thankful for his expert scientific
advice, the interesting discussions and his support. For the supervision of my work I am also
very grateful to Prof. Dr. Willi Auwarter. He knows both the experimental setup and the scien-
tific background and was always able to answer my questions. I am thankful for the scientific
discussions, the proof-reading, the support in the lab and the enjoyable working atmosphere.
Furthermore, I would like to thank Dr. Knud Seufert for introducing me to the STM and the
lab, for supervising many of my experiments and for passing on the porphyrins to me.
I am grateful to the whole LT-STM/AFM group. The size and composition changed quite a bit
but it was always a productive and friendly environment and I enjoyed the common times in the
lab, the discussions and the support from everybody. I thank Dr. Saranyan Vijayaraghavan and
Sushobhan Joshi for introducing me to the lab; Felix Bischoff, Jose I. Urgel Tendero and Tobias
Kaposi for the teamwork during the past three years; Dr. David Ecija and Dr. Manuela Garnica
Alonso for the scientific and other advice and Yuanqin He, Martin Schwarz, Jacob Ducke and
Domenik Zimmermann for their support.
Moreover, I would like to thank Dr. Anthoula Papageorgiou, Dr. Joachim Reichert, Dr. Francesco
Allegretti, Dr. Carlos-Andres Palma, Dr. Ozge Saglam, Dr. Florian Klappenberger, Dr. David
A. Duncan, Dr. Katharina Diller, Julian Lloyd and Prof. Dr. Peter Feulner for the joint projects
and for always answering my questions.
I am also grateful to Karl Eberle, Reinhold Schneider and Max Glanz for their advice and their
expertise. In addition, I thank our secretary Viktoria Blaschek for her support and her helpful-
ness.
Furthermore, I thank all the people from my office, Dr. Claudia Majer, Dr. Sebastian Jakob,
Dr. Knud Seufert, Richard Steinacher, Felix Bischoff, Juan Li, Li Jiang, Bi Hai, Martin Schwarz
and Martin Schaffer, for the nice atmosphere in our “Kofferraum“. Moreover, I thank everybody
from E20 for the support, for the scientific advice, for exciting stories from all over the world
and the overall great and inspiring atmosphere in the group.
I am very thankful to the International Max Planck Research School of Advanced Photon Sci-
ence (IMPRS) for the scholarship and the scientific program. I thank the IMPRS coordinators
Dr. Vladislav S. Yakovlev, Dr. Nick Karpowicz and Prof. Dr. Matthias Kling and all the IMPRS
students for the insightful and enjoyable meetings and I thank the secretary Monika Wild for
her organizational talent and her enthusiasm.
For the fruitful and enriching collaboration I am grateful to Prof. Dr. Joachim Schnadt and Ole-
sia Snezhkova. I also thank Dr. Thien H. Ngo for the synthesis of molecules. Furthermore, I am
very grateful to Dr. Alexander Weber-Bargioni and Sibel Leblebici for the exciting collaboration
and for welcoming me in their group.
Finally, I would like to thank everybody else who in some way supported me during the last
years. Especially, I thank my mother and my father (for the remained time that was given to
him) and my sisters Lara and Lisanne for standing by me and enriching my life. At last, I
cannot put into words how grateful I am to Peter for supporting me, believing in me and being
with me.