Ceramill TI alloy units - amanngirrbach.com · Ceramill M-Center / Sonderanfertigungen Cerarmeil...

10
VERARBEITUNG Ceramill M-Center / Sonderanfertigungen Ceramill TI alloy units Dentale Titanfräslegierung, Ti Al6 V4, Legierungstyp Titan Grade 5 Type 4 gemäß DIN ISO 22674 für festsitzenden metallkeramischen Zahnersatz. FRAMEWORK MANAGEMENT TECHNISCHE DATEN DIN EN ISO 9693 Zugfestigkeit 930 MPa 0,2 % – Dehngrenze 900 MPa Bruchdehnung 10 % Vickershärte 350 HV 5/30 WAK (25 - 500 °C) 10,3 10 –6 /K -1 Dichte 4,43 g/cm 3 Schmelzpunkt 1604 - 1660 °C CHEMISCHE ZUSAMMENSETZUNG (GEW. -%) Al 5,5 - 6,75 % V 3,5 - 4,5 % Andere < 0,4 % Rest TI Ceramill TI alloy entspricht Zenotec Ti von Wieland Dental. ANLIEFERUNG Das gefräste Gerüst wird im rohen, unbearbeiteten Zustand geliefert. WEITERE VERARBEITUNG UND VORBEREITUNG ZUR VERBLENDUNG _ Ggf. Gerüst mit sauberen für Titan geeigneten Hartmetall-Fräsern ausarbeiten, die Werkzeuge nur in eine Richtung über die Oberfläche ziehen, um Materialüberlappungen und eine möglicherweise daraus resultierende Blasenbildung bei keramischen Verbund zu vermeiden. _ Es muss auf die Hersteller empfohlene maximale Drehzahl der Instrumente geachtet werden. _ Oberflächen danach mit reinem Aluminiumoxid (ca. 180 μm) unter einem Druck von 2 - 3 bar abstrahlen. _ Gerüst danach gründlich unter fließendem Wasser abbürsten oder mit Heißdampf abdampfen und mit Ethylalkohol entfetten. Niemals Flusssäure verwenden! INDIKATIONSBEREICH Aus Ceramill Ti alloy lassen sich Kronen und Brücken für den Front- und Seitenzahnbereich fertigen. Brückengerüste für den Frontzahnbereich dürfen mit bis zu drei zusammenhängenden Zwischengliedern gefertigt werden. Der Verbinderquerschnitt darf 6 mm 2 nicht unterschreiten. Im Seitenzahnbereich dürfen Brücken nicht mehr als drei zusammen- hängende Zwischenglieder enthalten. Es ist ein Verbinderquerschnitt von mindestens 9 mm 2 zu realisieren. Seite 1/2 2014-04-07

Transcript of Ceramill TI alloy units - amanngirrbach.com · Ceramill M-Center / Sonderanfertigungen Cerarmeil...

Page 1: Ceramill TI alloy units - amanngirrbach.com · Ceramill M-Center / Sonderanfertigungen Cerarmeil M-Ceramill TI alloy units Dentale Titanfräslegierung, Ti Al6 V4, Legierungstyp Titan

V e ra r b e i t u n gCeramill M-Center / Sonderanfertigungen

Ceramill TI alloy units Dentale Titanfräslegierung, Ti Al6 V4, Legierungstyp Titan Grade 5 Type 4 gemäß DIN ISO 22674 für festsitzenden metallkeramischen Zahnersatz.

F ra m ewo r k m a n ag e m e n T

TeCHnISCHe DaTen

DIN EN ISO 9693

Zugfestigkeit 930 MPa

0,2 % – Dehngrenze 900 MPa

Bruchdehnung 10 %

Vickershärte 350 HV 5/30

WAK (25 - 500 °C) 10,3 10–6/K-1

Dichte 4,43 g/cm3

Schmelzpunkt 1604 - 1660 °C

CHemISCHe ZuSammenSeTZung (gew. -%)

Al 5,5 - 6,75 %

V 3,5 - 4,5 %

Andere < 0,4 %

Rest TI

Ceramill TI alloy entspricht Zenotec Ti von Wieland Dental.

anlIeFerung

Das gefräste Gerüst wird im rohen, unbearbeiteten Zustand geliefert.

weITere VerarbeITung unD VorbereITung

Zur VerblenDung

_ Ggf. Gerüst mit sauberen für Titan geeigneten Hartmetall-Fräsern

ausarbeiten, die Werkzeuge nur in eine Richtung über die Oberfläche

ziehen, um Materialüberlappungen und eine möglicherweise daraus

resultierende Blasenbildung bei keramischen Verbund zu vermeiden.

_ Es muss auf die Hersteller empfohlene maximale Drehzahl

der Instrumente geachtet werden.

_ Oberflächen danach mit reinem Aluminiumoxid (ca. 180 μm) unter

einem Druck von 2 - 3 bar abstrahlen.

_ Gerüst danach gründlich unter fließendem Wasser abbürsten oder

mit Heißdampf abdampfen und mit Ethylalkohol entfetten. Niemals

Flusssäure verwenden!

InDIkaTIonSbereICH

Aus Ceramill Ti alloy lassen sich Kronen und Brücken für den Front- und

Seitenzahnbereich fertigen. Brückengerüste für den Frontzahnbereich

dürfen mit bis zu drei zusammenhängenden Zwischengliedern gefertigt

werden. Der Verbinderquerschnitt darf 6 mm2 nicht unterschreiten.

Im Seitenzahnbereich dürfen Brücken nicht mehr als drei zusammen-

hängende Zwischenglieder enthalten. Es ist ein Verbinderquerschnitt

von mindestens 9 mm2 zu realisieren.

Seite 1/2

2014

-04

-07

Page 2: Ceramill TI alloy units - amanngirrbach.com · Ceramill M-Center / Sonderanfertigungen Cerarmeil M-Ceramill TI alloy units Dentale Titanfräslegierung, Ti Al6 V4, Legierungstyp Titan

V e ra r b e i t u n gCeramill M-Center / Sonderanfertigungen

F ra m ewo r k m a n ag e m e n T

VerblenDung

Opaquerbrand und Verblendung nach Angaben des Keramikherstellers.

Bei Verwendung von Creation TI wird empfohlen den zugehörigen

Bonder zu verwenden.

FInISH

Metallränder mit Silikon-Polierer auf Hochglanz bringen

(Hitzeentwicklung vermeiden).

laSerSCHweISSen

Zum Laserschweißen von Ceramill TI alloy wird ein Laserschweißdraht

Ti Al6 V4 empfohlen. Zu beachten sind die jeweiligen Herstellerangaben.

konTraInDIkaTIon

_ bei Unverträglichkeit der aufgeführten Bestandteile

_ Vorsicht in Anwendung bei Kindern und Schwangeren

SCHuTZempFeHlung

Stäube nicht einatmen, entsprechende Schutzmaßnahmen treffen

(Absaugung oder Staubmaske verwenden).

gewäHrleISTung

Anwendungstechnische Empfehlungen, ganz gleich ob sie mündlich,

schriftlich oder im Zuge praktischer Anleitung erteilt werden, beruhen

auf unseren eigenen Erfahrungen und Versuchen und können daher

nur als Richtlinie gelten. Unsere Produkte unterliegen einer kontinu-

ierlichen Weiterentwicklung. Wir behalten uns daher Änderungen in

Konstruktion und Zusammensetzung vor.

Ceramill TI alloy units Dentale Titanfräslegierung, Ti Al6 V4, Legierungstyp Titan Grade 5 Type 4 gemäß DIN ISO 22674 für festsitzenden metallkeramischen Zahnersatz.

Seite 2/2

Manufacturer | Hersteller | Distribution | Vertrieb

amann girrbach agHerrschaftswiesen 1 | 6842 Koblach | Austria | Fon +43 5523 62333-105Fax +43 5523 62333-5119 | [email protected] | www.amanngirrbach.com

Distribution | Vertrieb D/A

amann girrbach gmbHDürrenweg 40 | 75177 Pforzheim | Germany | Fon +49 7231 957-100Fax +49 7231 957-159 | [email protected] | www.amanngirrbach.com

Page 3: Ceramill TI alloy units - amanngirrbach.com · Ceramill M-Center / Sonderanfertigungen Cerarmeil M-Ceramill TI alloy units Dentale Titanfräslegierung, Ti Al6 V4, Legierungstyp Titan

P r o c ess i n gCeramill M-Center / Custom-made units

Ceramill TI alloy units Dental titanium milling alloy, Ti Al6 V4, alloy type Grade 5 Type 4 according to DIN ISO 22674 for fixed porcelain-bonded restorations.

F ra m ewo r k m a n ag e m e n T

TeChnICal daTa

DIN EN ISO 9693

Tensile strength 930 MPa

0,2 % – limit of elasticity 900 MPa

Ultimate strain 10 %

Vickers-hardness 350 HV 5/30

Coefficient of thermal 10,3 10–6/K-1

expansion (25 - 500 °C)

Density 4,43 g/cm3

Melting point 1604 - 1660 °C

ChemICal ComposITIon (perCenTage by weIghT)

Al 5,5 - 6,75 %

V 3,5 - 4,5 %

Others < 0,4 %

Rest TI

Ceramill Ti alloy corresponds to Zenotec Ti from Wieland Dental.

delIvery

The milled substructure is delivered in a raw, unfinished state.

FurTher proCessIng and preparaTIon

For veneerIng

_ If required, prepare the framework using clean tungsten carbide

cutters, which are suitable for titanium. Only move the cutter over

the surface in one direction to avoid overlapping and possible bubble

formation that may result from this during porcelain bonding.

_ It is essential to adhere to the manufacturer’s recommended

maximum rpm.

_ Then sandblast the surfaces with pure aluminium oxide

(approx. 180 μm) at a pressure of 2 - 3 bar.

_ After sandblasting, brush the framework thoroughly under running

water or steam clean and degrease using ethyl alcohol. Never use

hydrofluoric acid.

IndICaTIon range

Ceramill Ti alloy can be used for fabricating anterior and posterior

crowns and bridges. Bridge frameworks for the anterior region can be

fabricated with up to three connected pontics. The cross section of the

connectors should not be less than 6 mm2. Bridges in the posterior

region should not have more than three connected pontics.

The connector cross section should be a minimum of 9 mm2.

Page 1/2

2014

-04

-14

Page 4: Ceramill TI alloy units - amanngirrbach.com · Ceramill M-Center / Sonderanfertigungen Cerarmeil M-Ceramill TI alloy units Dentale Titanfräslegierung, Ti Al6 V4, Legierungstyp Titan

P r o c ess i n gCeramill M-Center / Custom-made units

F ra m ewo r k m a n ag e m e n T

veneer

Finish opaque firing and veneering according to the manufacturer’s

indications. When using Creation TI, it is advisable to use the

corresponding bonder.

FInIshIng

Polish metal rims with a silicone wheel (prevent heating up).

laser weldIng

Ti A16 V6 laser welding wire is recommended for laser welding Ceramill

Ti alloy. Adhere to the alloy manufacturer’s instructions.

ConTraIndICaTIon

_ in the event of incompatibility of the components listed

_ be cautious in the application with children and pregnant women

proTeCTIve reCommendaTIon

Do not inhale dust, protective measures to be taken

(apply vaccuum or facial mask).

guaranTee

Application recommendations, no matter whether verbally, in writing,

or by means of practical instructions are based on our experience and

tests and are thus only a recommendation. Our products are subject

to continuous further development. We reserve the right to alter the

products in terms of design or composition.

Page 2/2

Ceramill TI alloy units Dental titanium milling alloy, Ti Al6 V4, alloy type Grade 5 Type 4 according to DIN ISO 22674 for fixed porcelain-bonded restorations.

Manufacturer | Hersteller | Distribution | Vertrieb

amann girrbach agHerrschaftswiesen 1 | 6842 Koblach | Austria | Fon +43 5523 62333-105Fax +43 5523 62333-5119 | [email protected] | www.amanngirrbach.com

Distribution | Vertrieb D/A

amann girrbach gmbhDürrenweg 40 | 75177 Pforzheim | Germany | Fon +49 7231 957-100Fax +49 7231 957-159 | [email protected] | www.amanngirrbach.com

Page 5: Ceramill TI alloy units - amanngirrbach.com · Ceramill M-Center / Sonderanfertigungen Cerarmeil M-Ceramill TI alloy units Dentale Titanfräslegierung, Ti Al6 V4, Legierungstyp Titan

T ra i T e m e n TCeramill M-Center / Réalisations particulières

Ceramill TI alloy units Alliage dentaire en titane à fraiser Ti Al6 V4 de type 4 et de grade 5 conforme à la norme DIN ISO 22674 pour la réalisation de prothèses dentaires céramo-métalliques fixées.

F ra m ewo r k m a n ag e m e n T

FIChe TeChnIque

DIN EN ISO 9693

Résistance à la traction 930 MPa

0,2 % – limite de l’extansion 900 MPa

Allongement à la rupture 10 %

Dureté Vickers 350 HV 5/30

WAK (25 - 500 °C) 10,3 10–6/K-1

Densité 4,43 g/cm3

Point de fusion 1604 - 1660 °C

ComposITIon ChImIque (poIds -%)

Al 5,5 - 6,75 %

V 3,5 - 4,5 %

Autres < 0,4 %

Reste TI

L’alliage Ceramill TI correspond à l’alliage Zenotec Ti

de Wieland Dental.

LIvraIson

L’armature fraisée est livrée à l’état brut non traité.

Travaux CompLémenTaIres eT préparaTIFs

au revêTemenT

_ Finir éventuellement l’armature avec une fraise en carbure de

tungstène propre et adaptée au titane; appliquer l’instrument sur la

surface dans une seule direction afin d’éviter tout chevauchement de

matériau; ce qui permet d’éviter l’apparition de bulles lors de la

réalisation de la céramique.

_ Respecter la vitesse de rotation maximale de l’instrument préconisée

par le fabricant.

_ Sabler ensuite les surfaces à l’aide d’oxyde d’aluminium pur

(environ 180 μm) sous une pression de 2 - 3 bars.

_ Brosser ensuite soigneusement l’armature sous l’eau courante ou la

passer à la vapeur surchauffée puis la dégraisser à l’alcool éthylique.

Ne jamais utiliser d’acide fluorhydrique!

Le zone d’InTérêT

L’alliage Ceramill Ti permet de réaliser des couronnes et des bridges

dans les secteurs dentaires antérieurs et latéraux. Les armatures pour

bridges dans le secteur antérieur ne peuvent comporter que trois

éléments intermédiaires au maximum. La section transversale des

connecteurs ne doit pas être inférieure à 6 mm2.

Les bridges ne doivent pas comporter plus de trois éléments inter-

médiaires dans les secteurs latéraux. Il est nécessaire de réaliser des

sections transversales de connecteurs d’au moins 9 mm2.

Page 1/2

2014

-04

-14

Page 6: Ceramill TI alloy units - amanngirrbach.com · Ceramill M-Center / Sonderanfertigungen Cerarmeil M-Ceramill TI alloy units Dentale Titanfräslegierung, Ti Al6 V4, Legierungstyp Titan

T ra i T e m e n TCeramill M-Center / Réalisations particulières

F ra m ewo r k m a n ag e m e n T

revêTemenT

Cuisson opaqueur et revêtement selon les indications du fabricant de

la céramique. Pour l’emploi de Creation TI il est recommandé d’utiliser le

bonder afférent.

FInITIon

Polir miroir les bords en métal avec une pâte à la silicone

(éviter dégagement de chaleur).

soudure au Laser

Il est recommandé d’utiliser un fil de soudure Ti Al6 V4 pour la soudure

au laser de l’alliage Ceramill TI. Veuillez respecter les instructions du

fabricant.

ConTre-IndICaTIons

_ Réactions allergiques connues à certains composants

_ Prudence à l’emploi chez les enfants et les femmes enceintes

mesure de préCauTIon

Ne pas aspirer les poussières, prendre des mesures de protection

adéquates (utiliser un système d’aspiration ou un masque à poussière).

garanTIe

Les conseils techniques d’application délivrés, que ce soit oralement,

par écrit ou dans le cadre de conseils pratiques, sont fondés sur nos

propres expériences et essais. Ils doivent donc être pris uniquement

comme directives. Nos produits sont soumis régulièrement à des

évolutions. Par conséquent nous nous réservons le droit de modifications

de construction et de composition.

Page 2/2

Ceramill TI alloy units Alliage dentaire en titane à fraiser Ti Al6 V4 de type 4 et de grade 5 conforme à la norme DIN ISO 22674 pour la réalisation de prothèses dentaires céramo-métalliques fixées.

Manufacturer | Hersteller | Distribution | Vertrieb

amann girrbach agHerrschaftswiesen 1 | 6842 Koblach | Austria | Fon +43 5523 62333-105Fax +43 5523 62333-5119 | [email protected] | www.amanngirrbach.com

Distribution | Vertrieb D/A

amann girrbach gmbhDürrenweg 40 | 75177 Pforzheim | Germany | Fon +49 7231 957-100Fax +49 7231 957-159 | [email protected] | www.amanngirrbach.com

Page 7: Ceramill TI alloy units - amanngirrbach.com · Ceramill M-Center / Sonderanfertigungen Cerarmeil M-Ceramill TI alloy units Dentale Titanfräslegierung, Ti Al6 V4, Legierungstyp Titan

L avo ra z i o n eCeramill M-Center / Produzioni speciali

Ceramill TI alloy units Lingotti di lega dentale di titanio per fresaggio, Ti Al6 V4, di grado 5 tipo 4 secondo le norme DIN ISO 22674, per protesi dentale fissa di metalloceramica.

F ra m ewo r k m a n ag e m e n T

DaTI TeCnICI

DIN EN ISO 9693

Resistenza alla trazione 930 MPa

0,2 % – Limite di elasticità 900 MPa

Allungamento alla rottura 10 %

Durezza Vickers 350 HV 5/30

Coefficiente di dilatazione 10,3 10–6/K-1

termica (25 - 500 °C)

Densità 4,43 g/cm3

Punto di fusione 1604 - 1660 °C

ComposIzIone ChImICa (% Del peso)

Al 5,5 - 6,75 %

V 3,5 - 4,5 %

Altro < 0,4 %

Resto TI

La lega Ceramill TI corrisponde a Zenotec Ti della Wieland Dental.

FornITura

La struttura fresata viene fornita grezza, non lavorata.

ulTerIore lavorazIone e preparazIone

per Il rIvesTImenTo

_ Se necessario, rifinire la struttura con frese al carburo di tungsteno

indicate per la lavorazione del titanio. Le frese devono muoversi sulla

superficie sempre nella stessa direzione, per evitare sovrapponimenti

del materiale e una relativa possibile creazione di bolle d’aria nella

ricopertura di ceramica.

_ Rispettare le velocità massime di rotazione indicate dal produttore

delle frese.

_ Successivamente sabbiare le superfici con ossido di alluminio puro

(circa 180 μm) con una pressione di 2 - 3 bar.

_ In seguito pulire accuratamente l’armatura con una spazzola sotto

acqua corrente, oppure con una vaporizzatrice e sgrassarla con alcol

etilico. Non usare mai acido fluoridrico!

seTTore InDICazIone

Con i lingotti di lega Ceramill Ti si possono realizzare ponti e corone

anteriori e posteriori. Le strutture dei ponti anteriori possono essere

costruiti con un massimo di fino a tre elementi intermedi contigui. La

sezione dei connettori non deve essere inferiore ai 6 mm2. Nei denti

posteriori i ponti non possono avere più di tre elementi intermedi uniti

tra loro e i connettori devono avere una sezione di almeno 9 mm2.

Pagina 1/2

2014

-04

-14

Page 8: Ceramill TI alloy units - amanngirrbach.com · Ceramill M-Center / Sonderanfertigungen Cerarmeil M-Ceramill TI alloy units Dentale Titanfräslegierung, Ti Al6 V4, Legierungstyp Titan

L avo ra z i o n eCeramill M-Center / Produzioni speciali

F ra m ewo r k m a n ag e m e n T

rIvesTImenTo

Cottura dell’opaco e rivestimento secondo le indicazioni del produttore

della ceramica. Se si impiega Creation TI si consiglia di impiegare

l’adesivo corrispondente.

FInITura

Lucidare a specchio i bordi in metallo con molette al silicone

(evitare lo sviluppo di calore).

salDaTura laser

Per la saldatura con il laser della lega Ceramill Ti si consiglia di

usare l’apposito filo di Ti Al6 V4. Rispettare le relative indicazioni

del produttore.

ConTroInDICazIonI

_ In caso di intolleranza ai componenti indicati

_ Attenzione in caso di utilizzo in caso di bambini o donne in gravidanza

mIsure DI proTezIone ConsIglIaTe

Non inalare le polveri. Prendere misure di protezione adeguate

(impiegare aspiratore o maschera antipolvere).

garanzIa

Consigli di tipo tecnico-applicativo, indipendentemente se dati oral-

mente, per iscritto o nel quadro di istruzioni pratiche, si basano sulla

nostra esperienza e sui nostri tentativi personali e possono valere solo

come linee guida. I nostri prodotti sono soggetti ad aggiornamenti

continui, pertanto ci riserviamo modifiche nella progettazione e nella

composizione.

Pagina 2/2

Ceramill TI alloy units Lingotti di lega dentale di titanio per fresaggio, Ti Al6 V4, di grado 5 tipo 4 secondo le norme DIN ISO 22674, per protesi dentale fissa di metalloceramica.

Manufacturer | Hersteller | Distribution | Vertrieb

amann girrbach agHerrschaftswiesen 1 | 6842 Koblach | Austria | Fon +43 5523 62333-105Fax +43 5523 62333-5119 | [email protected] | www.amanngirrbach.com

Distribution | Vertrieb D/A

amann girrbach gmbhDürrenweg 40 | 75177 Pforzheim | Germany | Fon +49 7231 957-100Fax +49 7231 957-159 | [email protected] | www.amanngirrbach.com

Page 9: Ceramill TI alloy units - amanngirrbach.com · Ceramill M-Center / Sonderanfertigungen Cerarmeil M-Ceramill TI alloy units Dentale Titanfräslegierung, Ti Al6 V4, Legierungstyp Titan

P r o c esa m i e n toCeramill M-Center / Fabricaciones especiales

Ceramill TI alloy units Aleación dental de titanio para fresar, Ti Al6 V4, tipo de aleación Titanio Grado 5 Tipo 4 según DIN ISO 22674 para prótesis dental ceramometálica fija.

F ra m ewo r k m a n ag e m e n T

DaTos TéCnICos

DIN EN ISO 9693

Resistencia a la tracción 930 MPa

0,2 % – Límite de elasticidad 900 MPa

Elongación de rotura 10 %

Dureza Vickers 350 HV 5/30

CET (25 - 500 °C) 10,3 10–6/K-1

Peso específico 4,43 g/cm3

Punto de fusión 1604 - 1660 °C

ComposICIón químICa (% en peso)

Al 5,5 - 6,75 %

V 3,5 - 4,5 %

Otras < 0,4 %

Resto TI

Ceramill TI alloy equivale a Zenotec Ti de Wieland Dental.

enTrega

La estructura fresada se entrega en estado bruto sin tratar.

proCesamIenTo posTerIor y preparaCIón para

el revesTImIenTo

_ En caso necesario, desbastar la estructura con fresas de carburo de

tungsteno limpias, especiales para titanio. Las herramientas única-

mente deberán moverse sobre la superficie en una dirección, para

evitar solapamientos de material y la posible formación de burbujas

que éstos solapamientos pueden provocar en la unión cerámica.

_ Deberá observarse la velocidad de giro máxima recomendada por los

fabricantes de los instrumentos.

_ A continuación, las superficies deberán chorrearse con óxido de

aluminio puro (aprox. 180 μm) con una presión de 2 - 3 barios.

_ Acto seguido, deberá cepillarse a fondo la estructura bajo agua

corriente o bien con un chorro de vapor caliente y desengrasarla con

alcohol etílico. ¡Nunca deberá utilizarse ácido fluorhídrico!

gama De InDICaCIones

Ceramill Ti alloy permite elaborar coronas y puentes para el sector

anterior y posterior. Las estructuras para puentes en el sector anterior

pueden fabricarse con un máximo de tres pónticos contiguos.

La sección transversal de la unión no deberá ser inferior a 6 mm2.

En el sector posterior los puentes no deberán incluir más de tres

pónticos contiguos. Deberá observarse una sección transversal de como

mínimo 9 mm2 en las uniones.

Página 1/2

2014

-04

-14

Page 10: Ceramill TI alloy units - amanngirrbach.com · Ceramill M-Center / Sonderanfertigungen Cerarmeil M-Ceramill TI alloy units Dentale Titanfräslegierung, Ti Al6 V4, Legierungstyp Titan

P r o c esa m i e n toCeramill M-Center / Fabricaciones especiales

F ra m ewo r k m a n ag e m e n T

revesTImIenTo

Cocción de opaquer y revestimiento según las indicaciones del fabri-

cante de la cerámica. Si se emplea Creation TI se recomienda usar el

adhesivo correspondiente.

aCabaDo

Pulir los márgenes metálicos a alto brillo con pulidores de silicona

(evitar la generación de calor).

solDaDura láser

Para soldar Ceramill TI alloy con láser se recomienda un hilo de

soldadura láser Ti Al6 V4. Deberán observarse las correspondientes

indicaciones del fabricante.

ConTraInDICaCIones

_ en caso de intolerabilidad a los componentes citados

_ cuidado en el uso en niños y mujeres embarazadas

reComenDaCIones De proTeCCIón

No respirar el polvo, adoptar las correspondientes medidas de protección

(aspiración o máscara antipolvo).

garanTía

Las recomendaciones técnicas para el uso, independientemente de su

transmisión oral, escritas o transmitidas en el marco de una instrucción

práctica, se basan en nuestras propias experiencias y ensayos, por lo

tanto sólo pueden ser consideradas como pauta. Nuestros productos

están sometidos a un continuo perfeccionamiento. Por esta razón nos

reservamos el derecho a realizar modificaciones tanto del diseño como

de la composición.

Página 2/2

Ceramill TI alloy units Aleación dental de titanio para fresar, Ti Al6 V4, tipo de aleación Titanio Grado 5 Tipo 4 según DIN ISO 22674 para prótesis dental ceramometálica fija.

Manufacturer | Hersteller | Distribution | Vertrieb

amann girrbach agHerrschaftswiesen 1 | 6842 Koblach | Austria | Fon +43 5523 62333-105Fax +43 5523 62333-5119 | [email protected] | www.amanngirrbach.com

Distribution | Vertrieb D/A

amann girrbach gmbHDürrenweg 40 | 75177 Pforzheim | Germany | Fon +49 7231 957-100Fax +49 7231 957-159 | [email protected] | www.amanngirrbach.com