Ematic Genesis 2 Ladestation Ersatz - ifixit-guide-pdfs.s3 ... Ematic Genesis 2 Ladestation Ersatz...

download Ematic Genesis 2 Ladestation Ersatz - ifixit-guide-pdfs.s3 ... Ematic Genesis 2 Ladestation Ersatz Befolgen

of 6

  • date post

    13-Sep-2019
  • Category

    Documents

  • view

    0
  • download

    0

Embed Size (px)

Transcript of Ematic Genesis 2 Ladestation Ersatz - ifixit-guide-pdfs.s3 ... Ematic Genesis 2 Ladestation Ersatz...

  • Ematic Genesis 2 Charging Port Replacement Follow this guide to replace the charging port in the Ematic Genesis 2 tablet.

    Geschrieben von: Alexandria Ehrnsberger

    Ematic Genesis 2 Charging Port Replacement Entwurf: 2019-01-03Anleitung Nr: 53048 -

    © iFixit — CC BY-NC-SA de.iFixit.com Seite 1 von 6

  • EINLEITUNG

    This repair guide will teach you how to replace the charging port in the Ematic Genesis 2 tablet.

    WERKZEUGE: Phillips #00 Screwdriver (1) Metal Spudger (1) Soldering Iron (1)

    TEILE: Ematic 2 Charging Port (1)

    Ematic Genesis 2 Charging Port Replacement Entwurf: 2019-01-03Anleitung Nr: 53048 -

    © iFixit — CC BY-NC-SA de.iFixit.com Seite 2 von 6

    file:///Store/Tools/Phillips-00-Screwdriver/IF145-006?o=4 file:///Store/Tools/Metal-Spudger/IF145-012?o=5 file:///Store/Tools/Soldering-Iron-60w-Hakko-503F/IF317-092?o=1 file:///Artikel/Ematic_2_Charging_Port

  • Schritt 1 — Charging Port

    With your fingers, carefully pry off the back plastic casing. Starting at the corners is usually the easiest.

    Schritt 2

    Remove all four screws surrounding the battery with the Phillips head screwdriver.

    Carefully remove the battery from the device using the Metal Spudger tool to gently separate the battery by wedging it between the device and the battery.

    Ematic Genesis 2 Charging Port Replacement Entwurf: 2019-01-03Anleitung Nr: 53048 -

    © iFixit — CC BY-NC-SA de.iFixit.com Seite 3 von 6

  • Schritt 3

    Remove both screws on either side of the audio jack using the Philips head screwdriver.

    Detach audio jack from device.

    Schritt 4

    Remove the 3 screws surrounding the circuit board using the Philips head screwdriver.

    Carefully disconnect the circuit board from the device by detaching the copper flexible PCB ribbon cable.

    Ematic Genesis 2 Charging Port Replacement Entwurf: 2019-01-03Anleitung Nr: 53048 -

    © iFixit — CC BY-NC-SA de.iFixit.com Seite 4 von 6

  • To reassemble your device, follow these instructions in reverse order.

    Schritt 5

    Use a soldering iron to heat the solder holding the charging port to the circuit board.

    Remove the charging port from board using tweezers.

    Schritt 6

    Solder replacement port into place.

    Make sure all connections match original.

    Ematic Genesis 2 Charging Port Replacement Entwurf: 2019-01-03Anleitung Nr: 53048 -

    © iFixit — CC BY-NC-SA de.iFixit.com Seite 5 von 6

  • Dieses Dokument wurde zuletzt angelegt am 2019-08-12 12:42:56 PM.

    Ematic Genesis 2 Charging Port Replacement Entwurf: 2019-01-03Anleitung Nr: 53048 -

    © iFixit — CC BY-NC-SA de.iFixit.com Seite 6 von 6

    Ematic Genesis 2 Charging Port Replacement Geschrieben von: Alexandria Ehrnsberger EINLEITUNG

    WERKZEUGE: TEILE: Schritt 1 — Charging Port Schritt 2 Schritt 3 Schritt 4 Schritt 5 Schritt 6