GSM- Remote Control GSM-Basic, W-Bus Software...

24
Software v.8.1 Further vehicle-specific information is available on our website. Eine deutsche Version dieser Anleitung und weitere Informationen sind auf unserer Webseite zu finden. www.danhag.de Operating Manual GSM- Remote Control GSM-Basic, W-Bus

Transcript of GSM- Remote Control GSM-Basic, W-Bus Software...

Page 1: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

Software v.8.1

Further vehicle-specific information is available on our website.Eine deutsche Version dieser Anleitung und weitere Informationen sind auf unserer Webseite zu finden.www.danhag.de

Operating Manual

GSM- Remote Control GSM-Basic, W-Bus

Page 2: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

For the sake of the environment, we try to use no more packaging than necessary for our equipment.

2-24

Page 3: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

Index

1 Included in Delivery......................................................................................................................4

2 Notes on Safety............................................................................................................................5

3 Intended Use................................................................................................................................5

4 Obligations and Liabilities.............................................................................................................6

5 Malfunctions.................................................................................................................................6

6 Disposal....................................................................................................................................... 6

7 Device Description.......................................................................................................................7

7.1 Functions..............................................................................................................................7

7.2 Verification of the Switching Operation..................................................................................7

7.3 Alarm Feature.......................................................................................................................8

7.4 Connectors...........................................................................................................................8

8 SIM Card......................................................................................................................................9

9 Inputs and Outputs.....................................................................................................................10

10 Installation of the GSM Remote Control ...................................................................................11

10.1 Connecting the GSM Remote Control...............................................................................11

10.2 Connecting the GSM Remote Control to the Parking Heater............................................12

10.3 W-Bus (applies only to GSM remote control, W-bus model).............................................13

10.4 Heating Fan......................................................................................................................14

11 Configuration............................................................................................................................15

11.1 Configuration via SMS.......................................................................................................15

Contact Numbers / Master Number...........................................................................................15

11.2 Function Overview Table...................................................................................................17

11.3 Manual Configuration via SMS / Message Syntax.............................................................17

11.4 SMS commands................................................................................................................18

11.5 Deleting a Contact Number...............................................................................................19

12 Setting Up the GSM Remote Control........................................................................................19

13 Manufacturer............................................................................................................................21

14 Technical Specifications...........................................................................................................21

15 Copyrights and Trademarks......................................................................................................21

16 Declaration of Conformity.........................................................................................................21

17 Troubleshooting........................................................................................................................22

3-24

Page 4: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

1 Included in Delivery

● GSM remote control● GSM antenna (straight)● 8-pole connector cable● operating manual

(picture for illustration purposes only)

Optional Accessories

● cable wire harnesses for particular vehicles● Y-connector cables for Webasto and Eberspächer control elements● adhesive windshield antenna● GSM antenna adaptor

(picture for illustration purposes only)

4-24

Attention: Use of this GSM remote control requires a GSM SIM card, which is not included in the delivery.

Page 5: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

2 Notes on SafetyBefore using the GSM remote control, be sure to read this operating manual in its entirety! Heed the safety warnings herein in addition to universal and local regulations for accident prevention and protection of the environment. Keep this manual for later reference. Never operate the GSM remote control in environments where there are or may be flammable gas, fumes, liquid, or dust present.

3 Intended UseThe GSM remote control allows you to switch a device on and off by means of a telephone call. It is intended exclusively for private use and should not be used for commercial or industrial applications. Use it only as specified in this operating manual. The manufacturer holds no responsibility for damages resulting from unintended or incorrect use.

5-24

Attention: In order to reduce the risk of electric shocks and/or damage to the device, avoid exposing it to rain or moisture.

Attention: Do not use the GSM remote control to control life support or safety-critical systems, or devices which may pose a hazard when turned on or off unexpectedly.

Attention: Connect the GSM remote control only to devices with an operating voltage of +12VDC and a maximum current consumption of 1A.

Attention: The installation should be performed only by a trained specialist with the appropriate technical skills and equipment.

Page 6: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

4 Obligations and LiabilitiesThis GSM remote control was developed and manufactured using the best available technology and in accordance with generally accepted safety practices. However, this does not guarantee that the remote control will function as intended in all instances, at all times, and under all conditions.

5 MalfunctionsIf at any time its use is no longer absolutely hazard-free, take the GSM remote control out of operation immediately. Take all measures necessary to preclude its being put back into operation by accident. Repairs to the GSM remote control should be performed only by a qualified specialist.

6 DisposalTo dispose of this product, please turn it in at a designated collection point. Alternatively, you may return it to the manufacturer for environmentally friendly disposal.

6-24

Attention: Do not use the GSM remote control in cases where a malfunction might result in injury to persons or damage to property.

Note: For troubleshooting advice, see (section 17) of this manual. Frequently asked questions are answered on our website in the “FAQ“ section, which is updated continually. www.danhag.de

This product does not belong in the household garbage. Dispose of it only in accordance with the applicable regulations..

Page 7: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

7 Device Description

7.1 FunctionsThis GSM remote control has 3 switching outputs.The output signal for switching output 1 is configurable. Switching output 2 sends a +12VDC signal. Switching output 3 provides a ground signal.Switching can be triggered only by authorized telephone numbers. The switch-on duration can be set by the user.

7.1.1 GSM Remote Control BasicPossible output signals for switching output 1

▪ +12VDC

7.1.2 GSM Remote Control W-BUSPossible output signals for switching output 1:

▪ +12VDC▪ W-BUS

7.2 Verification of the Switching OperationWhen you place a call to the GSM remote control, you will hear a ringing tone first while it verifies the number of the caller. Once the switching operation has been triggered, the GSM remote control will break off the connection. You will then hear either a busy signal or a recorded announcement, depending on the telephone network operator. This indicates that the GSM remote control has initiated the switching operation.

7-24

Note: A W-BUS output signal is required by most Webasto auxiliary heaters, for example Thermo Top C, E, T, and V.

Page 8: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

7.3 Alarm FeatureAn alarm event causes notifications to be sent to up to 5 phone numbers via both calling and SMS.

7.4 Connectors

No. Description Function 1 antenna connector antenna connector (SMA jack)

2 Indicator LED green / red

blinking green (approx. once per second): connected, standing bycontinuous green: switching output activeblinking red: searching for network (not connected), bad receptioncontinuous red: error (see section 17)

3 connector X1 8-pole connector for power supply, switching output, etc.

8-24

Front view Rear view

Page 9: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

8 SIM CardUse of this GSM remote control requires any GSM SIM card. This can be either a prepaid card or a subscription card.

8.1 SIM Card Setup

8.2 Installation of the SIM Card▪ disconnect the 8-pole connection line from the GSM remote control▪ unscrew and open the remote control casing▪ insert the SIM card▪ close the casing

9-24

SIM-Karte

Note: Before installing the GSM SIM card, deactivate the PIN prompt and the voice mail function, and delete any saved telephone numbers.

Page 10: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

9 Inputs and Outputs

1 black: switch output 2• will provide a +12VCD signal for the pre-configured time• max. 1A

2 brown: ground 3 red: power supply +12VDC/3A4 orange: ignition In +12VDC *

• connect the ignition here if the switching outputs are to be disabled when the ignition is triggered

5 yellow: switching output 1• supplies a previously configured signal for the preset length of time (see 7.1 )• takes a maximum current of 1A

6 green: switching input +12VDC *• to trigger the switching operation manually, connect either a switch or a button here.• switch: switching output remains active as long as +12VDC is present, regardless of the preset signal length• button: a +12VDC pulse (approx. 1 second long) switches the switching outputs on or off for the preset length of time

10-24

1 black2 brown3 red4 orange5 yellow6 green7 blue8 purple

Page 11: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

7 blue: alarm In +12VDC *•connect the alarm lead to any present alarm system.•when put into operation, the GSM remote control checks whether 0 or +12VDC are present at the alarm connector. If this state changes, it alerts all 5 phone numbers by SMS and by calling them for approx. 30 seconds.•Set the alarm delay to define how long an uninterrupted alarm signal must be present before the alerts are sent (Point 11 ).

8 purple: switching output 3 / ground•supplies a groung signal for the preset length of time (not potential-free)•takes a maximum current of 500mA

• connection to these contacts not strictly required for basic functioning of device

10 Installation of the GSM Remote Control This GSM remote control allows you to switch on and off any device taking +12VDC and up to 1A of current. To connect it to a device taking a higher voltage, use a commercially available automotive relay.

10.1 Connecting the GSM Remote Control• connect the antenna

• connect the GSM remote control to the power supply protected by a 3A fuse

11-24

Attention: This GSM remote control is NOT designed to control 230VDC devices.

Page 12: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

10.2 Connecting the GSM Remote Control to the Parking HeaterThis GSM remote control allows you to control a parking heater system. Depending on the type of system, it may take a +12VDC, ground, or W-Bus control signal.

Connect switching output 1 (yellow) of the GSM remote control to the control input of the parking heater system, with switching output 1 (yellow) configured according to the type of heater used (see section 11.2 ).

Pin Function Pin Function 1 control input 12 2 control input

3 34 45 5 metering pump

6 metering pump 6 magnetic valve

78

12-24

Steuereingang Steuereingang

Thermotop C / Z Thermotop V, Evo

Note: Older heaters take either a ground or a +12VDC control signal; the heater runs as long as the signal is present. Newer heaters (for example, Thermo-Top C, V, EVO, etc.) are controlled with a W-Bus signal.

Page 13: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

10.3 W-Bus (applies only to GSM remote control, W-bus model)

Many modern Webasto parking heaters take a W-bus (serial data bus) control signal. This GSM remote control supports a number of different W-bus protocols.The protocol required depends on the heater and vehicle models.

W-bus data protocol

Heaters and control elements

W-Bus 3 protocol used by the original Webasto Comfort Preset Timer 1533

W-Bus 4 protocol used by Thermotop V heaters without a software upgrade

W-Bus 5 protocol used by many factory-provided auxiliary heaters

W-Bus 6 protocol used by original Webasto RF remote controls

13-24

Note: Refer to the table above in order to determine which W-bus protocol your parking heater system requires. If your heater or heater control is not listed, there is no harm in choosing the wrong one, so simply try out each protocol until you find one that works.

Note: Further installation tips are available on our website: www.danhag.de

Page 14: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

10.4 Heating FanBy default, the heating fan operates only when the ignition is switched on. In order to use the fan for the parking heater as well, install either a relay or an IPCU module.

Relay (usual for manual air conditioning systems)Bei Fahrzeugen mit manueller Klimaanlage wird die Drehzahl des Heizungsgebläses über einen mehrstufigen Gebläseschalter eingestellt. In diesem Fall müssen Sie ein zusätzliches KFZ-Relais installieren.

IPCU (usual for automatic air conditioning systems)In vehicles equipped with an automatic air conditioning (AC) system, the speed of the heating fan is controlled by a PWM signal (IPCU) and set from the AC control unit. In order to use the GSM remote control with such an AC system, connect an additional IPCU module.

14-24

Masse (br)

zum Gebläseschalter

PWM signal from the AC control unit

GSM remote controlW-Bus Converter with IPCU

Climate control(digital)

switching output 2 (black)

F4 (30) 40A

F3 (15) 40A

relay

ground

fan control

switching output 2 (black)

in (bl) out (pu)

Page 15: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

11 ConfigurationOnce the GSM remote control is installed and working, it must be configured by means of SMS. You can configure functions and settings as follows.

11.1 Configuration via SMSThe first time you start the GSM remote control, you must configure it via SMS. On our website www.danhag.de we have provided a configuration tool to generate and send configuration messages. Alternatively, you may use your own cellphone to create and send a configuration message (see section 11.3 ). If the configuration is successful, your GSM remote control will send a notification message to the master contact number (see section Fehler: Referenz nicht gefunden).

Password (factory default: 12345)• configuration of the GSM remote control via SMS requires a 5-digit password• the password may be changed, but must consist of 5 digits• if the GSM remote control is reset, the password is reset to the factory default

(12345)

Contact Numbers / Master Number• Up to 5 contact numbers can be saved.• The contact number in the first slot is the master number. This number receives all

status messages (see section 11 ).• The GSM remote control triggers the switching operation only when called by one of

the 5 contact numbers.•

15-24

Note: Include any international or regional prefix codes when entering the telephone numbers. Each number may contain up to 15 digits.

Note: The configuration tool does not check the input for errors(for example, regarding the type of parking heater, or the format of the number).

Page 16: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

Switch-on DurationThe length of time that the switching outputs send a signal can be configured to be•any number of seconds from 1 to 255•any number of minutes from 1 to 999•unlimited

Switch-on DelayTo delay the activation of switching output 2 (black), enter the delay here.

Switch-off DelaySelect how long the switching output 2 (black) should stay active after the „switch- on“ duration.

Parking Heater FanWhen selecting the parking heater fan funktion only switching output 2 (black) will be used. Switching output 1 and 3 won't be controlled.

Output Signal for Switching Output 1 (yellow)The GSM remote control supports +12VDC and W-Bus output signals (see section 7.1 )

Alarm DelaySet the alarm delay to define how long an uninterrupted alarm signal must be present before the alarm is triggered.

16-24

Note: Since it takes some time for the engine coolant to cool down after the parking heater is turned off, you can let the circulation pump and heating fan run for an additional five to ten minutes.

Note: The parking ventilator feature is not possible if the fan is controlled by the heating system unless you install an additional automotive relay.

Page 17: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

11.2 Function Overview Table

Nr. Funktion Mögliche Einstellung Bemerkung

00 password exactly five digits factory setting: 12345

11 master contact number up to 15 digits Include the international calling prefix. Examples:Germany +49...Austria +43...Switzerland +41...Example for Germany: +491707667763

12 contact number 2

13 contact number 3

14 contact number 4

15 contact number 5

20 switch-on duration (minutes)

0-1000 1-999: switch-on duration in minutes1000: remain switched on indefinitely

21 switch-on delay 0 – 999 minutes applies for switching output 2 (black)

22 switch-off delay 0 – 999 minutes applies for switching output 2 (black)

23 switch-on duration (seconds)

0 – 255 seconds 0 – 255 switch-on duration in seconds

30 output signal / switching output 1 (yellow)

0: parking ventilator1: +12V2: not assigned3: W-bus 34: W-bus 45: W-bus 56: W-bus 6

see section 7.1 , 10.1 , 10.3

40 alarm delay 0-250 seconds251: alarm disabled

alarm feature (optional)

11.3 Manual Configuration via SMS / Message SyntaxEach setting is referenced by a number. You can assign a value to a parameter by using an equals sign (=); each assignment must conclude with a semicolon (;). Multiple assignments may be combined into a single message (up to a maximum of 150 characters). The configuration message must conclude with a number sign #.

17-24

Page 18: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

Configuration exampleAn example configuration message is printed below which makes the following settings:Master contact number 1: 0305627853, contact number 2: 01706878981switch-on duration: 20=30; 23=5 equals 30 minutes 5 seconds, switch-on delay: 5 minswitch-off delay: 1 minute, switching output 1 (yellow) signal type: W-bus 3

Structure of the example configuration message:password; contact numbers; switch-on duration min;switch-on duration sec; switch-on delay;

switch-off delay; output signal for output 1 (yellow);

Configuration message to make the example settings:12345;11=+49305627853;12=+491706878981;20=30;23=5;21=5;22=1;30=3;#

11.4 SMS commandsYou can send the following SMS commands to the GSM Remote Control:

• On / Off: send this command in order to switch the heater ON or OFF

• Info: to request a listing of the current settings, send a text message consisting of the word "Info" to the GSM remote control. It will send a message to the master contact number detailing the current settings as well as the signal reception quality.An info message will be sent automatically whenever a new configuration message is received in order to acknowledge the new settings.

• Temp: retrieval of the current temperature within the GSM Modul• Startxxxx: it is possible to program an once off start time within a 24 hour circle.

For example send a SMS „start1630“ and the heater will switch on at 4:30 pm• Stop: switching off the heater and also deleting the programmed start time

18-24

Page 19: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

11.5 Deleting a Contact NumberTo delete a contact number, simply overwrite it with a zero.

12 Setting Up the GSM Remote Control● Insert a SIM card into the GSM remote control (as described in section 8 ).● Connect the GSM remote control (as described in section 10 ).● Configure the GSM remote control (as described in section 11 ).

19-24

(20) switch-on duration(21) switch-on delay(22) switch-off delay(30) output signal(40) alarm delay

DANHAG GSM

Status: off20) 30min; 5s21) 5min22) 1min30) +12V40) 2sTimer: 0830Signal: 22PWD: 12345SW: v8.1

Attention: The contact number to be deleted must be overwritten with at least one digit, or else the GSM module will not work correctly.

Page 20: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

When connected to a power supply the GSM remote control will run a self-test (indicated by the LED shining red for approx. 4 seconds), then begin searching for a network connection (LED flashing red). Once the GSM remote control has logged into the GSM network (LED flashing green), it is operational and ready for use.

20-24

Attention: Remember to deactivate the SIM card's PIN prompt as well as any call forwarding preferences.

Attention: Fuse the GSM remote control with 3A. If you have connected the GSM remote control using our optional Y-cable, ensure that the control unit is adequately fused..

Page 21: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

13 ManufacturerDANHAGIng. Büro GornickiJosef-Orlopp-Str.89-91 10365 Berlin Tel.: +49 (0)30 - 555 753 63Fax.: +49 (0)30 - 692 096 46 - 9E-Mail: [email protected]: www.danhag.de

14 Technical SpecificationsOperating voltage: +12VDCOperating current draw: max. 3AStandby current draw: <10mASwitching outputs: max.+12VDC, max. 1AOperating temperatures: -30°C – 70°CDimensions ( LxWxH ): 64 x 60 x 22mm (+ antenna length)

15 Copyrights and TrademarksAll copyrights and trademarks which are named in this manual and protected by third parties are subject to the provisions of the applicable labelling requirements and possessory titles of their registered owners. Simply naming trademarks and brands does not imply that they are not protected by third parties rights. The trademarks and brands named in this manual are the property of their respective owners and are used only for descriptive purposes.

16 Declaration of ConformityThis device conforms to the EC directive 2004/108/EG on electromagnetic compatibility.Standards applied: EN 50498 / 2011

21-24

Page 22: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

17 TroubleshootingDescription Error Possible causes

LED flashing red quickly GSM module not logged in - SIM card not inserted correctly - PIN prompt on SIM card not deactivated - no GSM signal

LED lights up red briefly approx. every 60s

- insufficient voltage - ensure that power supply provides 12V and 3A

GSM remote control does not switch when called

- faulty configuration - see section 11 - duplicate contact number entry on SIM card (delete all contact numbers and reconfigure)

status text message requested but not received

- no credit on SIM card - top up your SIM card credit

LED lights up red when device is called (W-bus only)

- remote control not connected to parking heater (W-bus only)

- while the GSM remote control is unplugged, check that +12VDC are present in the yellow terminal of the 8-pole connector- incorrect W-bus data protocol(see section 10.3 )- heater in malfunction lock-out mode (disconnect heater from power supply for at least 5min, or have error memory checked by a service partner)

heater stops running before configured time has elapsed

- insufficient voltage at heater - heater's running time limit reached

- ensure that vehicle's battery is charged- W-bus-controlled heaters have internal running time limit (30-250 min.)

heater does not start; LED lit green - incorrect W-bus data protocol- heater in malfunction lock-out mode (W-bus only)

- incorrect W-bus data protocol (see section 10.3 )- heater in malfunction lock-out mode (disconnect heater from power supply for at least 5min, or have error memory checked by a service partner)

Reset

Disconnect the 8-pole connector from the device for at least 3 minutes.

22-24

Page 23: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

23-24

Page 24: GSM- Remote Control GSM-Basic, W-Bus Software v.8webasto-russia.ru/GSM-module-Danhag-WBUS-v8.1-user-manual.pdf · GSM- Remote Control GSM-Basic, W-Bus . GSM- Fernsteuerung v 8.1 DANHAG

GSM- Fernsteuerung v 8.1 DANHAG 09.07.2013

Short User Guide

1. Install the GSM Remote Controll (see section 10 ) or connect it with a Y-cable

2. Insert the SIM card, after having de-activated the PIN-code (see section 8 )

3. Configure the GSM Remote Control ( see section 11 or www.danhag.de – SMS Programmierung)

4. Use your GSM Remote Controll to switch on/off your heater via phone call or SMS

SMS commands

On Switch on the heater

Off Switch off the heater

Temp Temperature retrival from within the modul

Start1630 24 hour programming to switch on (for example 04:30pm)

Stop Switches off the heater and also cancels a 24 hour programming

Info List of all current settings and status of the GSM Remote Control

24-24