Nickel + Nickel-Alloys · Strip / sheet 0.40 - 2.00 50 - 320 500 - 3000 Thickness Length 500 - 3000...

Auerhammer Metallwerk GmbH | Hammerplatz 1 | 08280 Aue (Sachsen) | Tel. +49 3771 272-0 |

Mail: [email protected] | www.auerhammer.com

Alloy Material | UNS No. Standard

Ni99.6 2.4060 DIN 17740 / DIN 17750

LC-Ni99.6 2.4061 DIN 17740 / DIN 17750

Ni99.2 2.4066 / N02200 DIN 17740 / DIN 17750 / ASTM B162

LC-Ni99 2.4068 / N02201 DIN 17740 / DIN 17750 / ASTM B162

Ni233 N02233 ASTM F3

Ni300 N03300 ASTM F290

1. Alloys

2. Chemical composition (Reference values in % w/w)

Alloy Ni (+Co) C Cu Fe Mg Mn S Si Ti

Ni99.6min. 99.6

max. 0.08 0.15 0.25 0.15 0.35 0.005 0.15 0.10

LC-Ni99.6min. 99.6

max. 0.02 0.15 0.25 0.15 0.35 0.005 0.15 0.10

R-Ni99.2min. 99.2

max. 0.10 0.25 0.40 0.15 0.35 0.005 0.25 0.10

LC-Ni99min. 99.0

max. 0.02 0.25 0.40 0.15 0.35 0.005 0.25 0.10

Ni233min. 99.0 0.01

max. 0.10 0.10 0.10 0.10 0.30 0.008 0.10 0.005

Ni300min. 97.0 0.20 0.20

max. 0.40 0.25 0.60 0.50 0.50 0.01 0.35 0.60

Nickel & Nickel-Alloys

01/1

7

3. Physical properties

Alloy Densitiy Specific electrical resistivity at 20 °C

Average linear thermal expansion coe#cient

20 °C - 100 °CCurie temperature

g/cm3 Ω • mm2/ m 10-6/K °C

BR-Ni99.6

8.9 0.09 13 360

LC-Ni99.6

R-Ni99.2

LC-Ni99

Ni233

Ni300 8.75 0.16 13 -



4. Mechanical properties (Reference values)

Alloy Condition Tensile strength Elongation Vickers hardness

MPa % HV

BR-Ni99.6

annealed min. 370 min. 40 max. 130

quarter hard min. 490 min. 15 ca. 150

hard min. 590 min. 2 ca. 200

LC-Ni99.6annealed min. 340 min. 40 max. 130


R-Ni99.2




LC-Ni99




Nickel 233




Nickel 300annealed min. 600 min. 15 max. 180


5. Dimensions and tolerances: Thickness & Width (in mm)

Thickness Width 10 -100 Width > 100 - 200 Width > 200 - 320

0.10 - 0.15 +/- 0.008 +/- 0.010 +/- 0.010

> 0.15 - 0.20 +/- 0.010 +/- 0.015 +/- 0.015

> 0.20 - 0.35 +/- 0.015 +/- 0.015 +/- 0.020

> 0.35 - 0.50 +/- 0.020 +/- 0.020 +/- 0.025

> 0.50 - 1.00 +/- 0.025 +/- 0.025 +/- 0.030

> 1.00 - 1.50 +/- 0.030 +/- 0.030 +/- 0.040

> 1.50 - 2.20 +/- 0.040 +/- 0.040 +/- 0.050

> 2.20 - 3.00 +/- 0.050 +/- 0.050 +/- 0.060

Width Thickness 0.10 - 1.00 Thickness > 1.00 - 1.80 Thickness > 1.80 - 2.50 Thickness > 2.50 - 3.00

10 - 100 + 0.2 + 0.3 + 0.5 + 1.0

> 100 - 200 + 0.3 + 0.5 + 0.7 + 1.2

> 200 - 320 + 0.6 + 1.0 + 1.2 + 1.5

Length (in mm)

7. Delivery forms (in mm)

Thickness Length 500 - 3000

0.4 - 2.00 + 10

Form Thickness Width Length Coil-ID Coil-OD

Coil 0.10 - 3.00 10 - 320 300 / 400 / 500 max. 1050

Strip / Sheet 0.40 - 2.00 50 - 320 500 - 3000

Important Note: All data in this Material Data Sheet are only for information purposes. Other dimensions and features to customer

specification on request. Guarantees relating to specific characteristics or purposes require always a special written agreement.



1. Alloys


Alloy Ni Mn Mo S Cr Cu C Si P Fe

FeNi36 36 < 0.5 < 0.2 < 0.010 < 0.3 < 0.3 < 0.02 < 0.2 < 0.01 balance

FeNi48 48 < 0.5 < 0.2 < 0.010 < 0.3 < 0.3 < 0.02 < 0.2 < 0.01 balance

FeNi77CuMo 77 < 0.6 4.1 < 0.010 < 0.3 4.4 < 0.02 < 0.2 < 0.01 balance

FeNi80Mo 80 < 0.7 4.9 < 0.010 < 0.3 < 0.3 < 0.02 < 0.3 < 0.01 balance

Soft-magnetic Iron-Nickel-Alloys


FeNi36 1.3910 / 1.3911 DIN 17745 / DIN 17405 / DIN EN 60404-8-6

FeNi481.3922 / 1.3926 / 1.3927 / K94840

DIN 17745 / DIN 17405 / DIN EN 60404-8-6 / ASTM A753

FeNi77CuMo 2.4530 / 2.4595 / 2.4596DIN 17745 / DIN 17405 /

DIN EN 60404-8-6

FeNi80Mo2.4530 / 2.4595 / 2.4596 / N14080

DIN 17745 / DIN 17405 / DIN EN 60404-8-6 / ASTM A 753 /

MIL-N-14411C

01/1

7


Alloy Density Bs

TC

HC

1 μ0.4

1 μmax

1 E-Modulus

g/cm3 T °C A/m DC-/AC DC-/AC GPa

FeNi36 8.15 1.2 240 10 6000 / 5000 25000 / 20000 135

FeNi48 8.25 1.5 470 4 10000 / 8000 150000 / 70000 150

FeNi77CuMo 8.76 0.75 410 0.5 200000 / 80000300000 / 100000

195

FeNi80Mo 8.75 0.75 410 0.5 250000 / 100000300000 / 150000

195

1 measured on ring cores, thickness 0.2 mm

Bs = Saturation Flux Density | T

C = Curie Temperature | H

C= Coercive Field Strength

μ0.4

= Initial Permeability | μmax

= Maximum Permeability

DC = Direct Current | AC = Alternating Current f = 50 Hz




Alloy Condition 0.2 % Yield strength Tensile strength Vickers hardness

MPa MPa HV

FeNi36annealed

hard280600

440700

140220

FeNi48annealed

hard270750

520850

140240

FeNi77CuMoannealed

hard320

1000630

1050160320

FeNi80Moannealed

hard3001100

6301150

160340


Thickness Width 10 - 50 Width > 50 - 200 Width > 200 - 320

0.10 - 0.20 +/- 0.010 +/- 0.015 +/- 0.020

> 0.20 - 0.50 +/- 0.020 +/- 0.020 +/- 0.030

> 0.50 - 1.00 +/- 0.030 +/- 0.030 +/- 0.040

> 1.00 - 2.00 +/- 0.040 +/- 0.040 +/- 0.050

> 2.00 - 2.50 +/- 0.050 +/- 0.050 +/- 0.060


10 - 50 +/- 0.1 +/- 0.2 +/- 0.2 +/- 0.3

> 50 - 200 +/- 0.2 +/- 0.3 +/- 0.3 +/- 0.4

> 200 - 320 +/- 0.3 +/- 0.4 +/- 0.5 +/- 0.6



Coil 0.10 - 2.50 10 - 320 300 / 400 / 500 max. 1050

Strip / sheet 0.40 - 2.00 50 - 320 500 - 3000


0.40 - 2.00 + 10

Length (in mm)






FeNi36 1.3912 SEW 385 / DIN 17745

FeNi41 1.3917 / K94100 DIN 17745 / ASTM F30

FeNi46 1.3920 / K94600 SEW 385 / DIN 17745 / ASTM F30

FeNi51 2.4478 / N14052 SEW 385 / DIN 17745 / ASTM F30

FeNi29Co18Mn 1.3981 / K94610 SEW 385 / DIN 17745 / ASTM F15

FeNi47Cr5Al

1. Alloys


Alloy Ni Co Mn Al Cu Cr Si Fe

FeNi36 36 < 0.10 < 0.50 < 0.05 < 0.3 < 0.3 < 0.30 balance

FeNi41 41 < 0.10 < 0.80 < 0.05 < 0.20 < 0.25 < 0.30 balance

FeNi46 46 < 0.10 < 0.80 < 0.05 < 0.20 < 0.25 < 0.30 balance

FeNi51 51 < 0.10 < 0.60 < 0.05 < 0.20 < 0.25 < 0.30 balance

FeNi29Co18Mn 29 17 < 0.50 < 0.05 < 0.20 < 0.20 < 0.20 balance

FeNi47Cr5Al 47 < 0.20 < 0.30 < 0.30 < 0.20 4.0 - 6.0 < 0.30 balance

Sealing & Expansion Alloys

Alloy Density Melting point

Specific electrical resistivity at 20 °C

Thermal conductivity at 20 °C E-Modulus

g /cm3 °C Ω • mm2/ m 10-6/K GPa

FeNi36 8.15 1435 0.79 13 137

FeNi41 8.20 1440 0.63 15 142

FeNi46 8.20 1450 0.55 16 152

FeNi51 8.25 1450 0.38 17 160

FeNi29Co18Mn 8.15 1450 0.46 17 157

FeNi47Cr5Al 8.25 1440 0.85


01/1

7

4. Thermal expansion properties

Alloy Average linear thermal expansion coe&cient in 10-6/K | Reference temperature 20 °C

Curietemperature

100 °C 150 °C 200 °C 300 °C 400 °C 500 °C 600 °C °C

FeNi36 1.5 1.9 2.6 5.3 8.1 9.9 11.1 230

FeNi41 4.6 4.4 4.2 4.2 5.8 7.9 9.4 340

FeNi46 7.9 7.8 7.7 7.4 7.3 8.6 9.7 400

FeNi51 10.3 10.3 10.2 10.1 9.9 10.0 10.9 500

FeNi29Co18Mn 6.5 6.2 5.9 5.4 5.1 6.2 7.8 435

FeNi47Cr5Al 8.8 8.9 8.9 9.0 9.4 10.6 12.0 345

Heat treatment 900 °C | Annealing time 0.5 h | Cooling time to 100 °C at least 10 h | Medium: hydrogen



Expansion Curves

5. Mechanical properties (Reference values soft-annealed)

Alloy 0,2 % Yield strength Tensile strength Elongation Vickers hardness

MPa MPa % HV

FeNi36 270 450 35 130

FeNi41 290 500 35 140

FeNi46 270 520 35 140

FeNi51 260 540 30 140

FeNi29Co18Mn 380 530 35 160

FeNi47Cr5Al 260 540 30 140

Average linear thermal expansioncoe&cientin 10-6/K

Temperature °C (Reference temperature 20 °C)



0.10 - 0.20 +/- 0.010 +/- 0.015 +/- 0.020

> 0.20 - 0.50 +/- 0.020 +/- 0.020 +/- 0.030

> 0.50 - 1.00 +/- 0.030 +/- 0.030 +/- 0.040

> 1.00 - 2.00 +/- 0.040 +/- 0.040 +/- 0.050

> 2.00 - 2.50 +/- 0.050 +/- 0.050 +/- 0.060


10 - 50 +/- 0.1 +/- 0.2 +/- 0.2 +/- 0.3

> 50 - 200 +/- 0.2 +/- 0.3 +/- 0.3 +/- 0.4

> 200 - 320 +/- 0.3 +/- 0.4 +/- 0.5 +/- 0.6

Length (in mm)



0.40 - 2.00 + 10


Coil 0.10 - 2.50 10 - 320 300 / 400 / 500 max. 1050

Strip / Sheet 0.40 - 2.00 50 - 320 500 - 3000



FeNi36

FeNi41

FeNi46

FeNi51

FeNi29Ca18Mn

FeNi47Cr5Al



1. Alloys


Alloy Ni (+Co) Cr Al C Cu Fe Mn Si Ti

LC-NiCr15Femin. 72 14 6

max. 16 0.3 0.025 0.5 10 1.0 0.5 0.3

NiCr15Femin. 72 14 0.025 6

max. 17 0.3 0.1 0.5 10 1.0 0.5 0.3

NiCr23Femin. 58 21 1.0

max. 63 25 1.7 0.1 0.5 18 1.0 0.5 0.5

NiCr9min. 9 0.2 0.1

max. balance 10 0.1 0.1 0.1 0.3 0.4 0.2 0.1

Nickel-Chrome-Alloys

01/1

7


LC-NiCr15Fe 2.4817 DIN 17742

NiCr15Fe 2.4816 / N06600 DIN 17742 / ASTM B168

NiCr23Fe 2.4851 / N06601 DIN 17742 / ASTM B168

NiCr9


Alloy Density

Average linear thermal expansion

coe"cient 20 °C - 100 °C

Thermal conductivity at 20 °C E-Modulus

g/cm3 10-6/K W/m • K GPa

LC-NiCr15Fe 8.5 14 11

NiCr15Fe 8.5 14 11

NiCr23Fe 8.2 14 11 207

NiCr9 8.3




Alloy 0.2 % Yield strength Tensile strength Elongation Vickers hardness

MPa MPa % HV

LC-NiCr15Fe 300 630 35 150

NiCr15Fe 300 700 35 170

NiCr23Fe 350 740 40 180

NiCr9 280 600 35 145



0.20 - 0.35 +/- 0.020 +/- 0.020 +/- 0.030

> 0.35 - 0.60 +/- 0.030 +/- 0.030 +/- 0.040

> 0.60 - 1.00 +/- 0.040 +/- 0.050 +/- 0.050

> 1.00 - 1.50 +/- 0.050 +/- 0.060 +/- 0.070

> 1.50 - 2.50 +/- 0.060 +/- 0.070 +/- 0.080

Length (in mm)



0.40 - 2.00 + 10


Coil 0.20 - 2.50 10 - 320 300 / 400 / 500 max. 1050

Strip / Sheet 0.40 - 2.00 50 - 320 500 - 3000



Width Thickness 0.20 - 1.00 Thickness > 1.00 - 1.80 Thickness > 1.80 - 2.50

10 - 100 + 0.2 + 0.3 + 0.5

> 100 - 200 + 0.3 + 0.5 + 0.7

> 200 - 320 + 0.6 + 1.0 + 1.2



AlloyNumeric

abbreviationsClassifiaction UNS-No.

DIN EN ISO 18274:2011 AWS 5.14:2011

NiCr30Fe9 Ni 6052 EQNiCrFe-7 N06052

NiCr23Mo16 Ni 6059 EQNiCrMo-13 N06059

NiCr20Mn3Nb Ni 6082 EQNiCr-3 N06082

NiCr22Mo9Nb Ni 6625 EQNiCrMo-3 N06625

NiCr15Mo16Fe6W4 Ni 6276 EQNiCrMo-4 N10267

NiCu30Mn3Ti Ni 4060 EQNiCu-7 N04060

NiTi3 Ni 2061 EQNi-1 N02061

1. Alloys


Welding Consumables

Alloy Ni Co Cu Fe C Cr Mn Si Ti Mo Nb Al W V

NiCr30Fe9min. 54.0 7.0 28.0

max. 0.3 11.0 0.04 31.5 1.0 0.50 1.0 0.5 0.10

NiCr23Mo16min. 56.0 22.0 15.0 0.1

max. 0.3 0.5 1.5 0.01 24.0 0.5 0.10 0.5 16.5 0.4 0.30

NiCr20Mn3Nbmin. 67.0 18.0 2.5 2.00

max. 0.5 3.0 0.10 22.0 3.5 0.50 0.7 3.00

NiCr22Mo9Nbmin. 58.0 20.0 8.0 3.15

max. 0.5 5.0 0.10 23.0 0.5 0.50 0.4 10.0 4.15 0.4

NiCr15Mo16Fe6W4min. 50.0 4.0 14.5 15.0 3.0

max. 2.5 0.5 7.0 0.02 16.5 1.0 0.80 17.0 4.5 0.35

NiCu30Mn3Timin. 62.0 28.0 2.0 1.5

max. 32.0 2.5 0.15 4.0 1.20 3.0 0.30 1.2

NiTi3

min. 92.0 2.0

max. 0.2 1.0 0.15 1.0 0.70 3.5 1.5

Additional welding consumables according to DIN EN ISO 18274, AWS A5.14 or according to separate

customer specifications are possible on request.





0.20 - 0.35 +/- 0.02 +/- 0.02 +/- 0.03

> 0.35 - 0.60 +/- 0.03 +/- 0.03 +/- 0.04

> 0.60 - 1.00 +/- 0.04 +/- 0.05 +/- 0.05

> 1.00 - 1.50 +/- 0.05 +/- 0.06 +/- 0.07

> 1.50 - 2.00 +/- 0.06 +/- 0.07 +/- 0.08


< 100 + 0.2 + 0.3 + 0.5

> 100 - 200 + 0.3 + 0.5 + 0.7

> 200 - 280 + 0.6 + 1.0 + 1.2


Form Thickness Width Coil-ID Coil-OD

Strip - soft 0.20 - 2.00 25 - 280 300 / 400 / 500 max. 1050

Strip - hard 0.50 30 - 180 300 / 400 / 500 max. 1050



The following tolerances apply to the standard dimension of hard-rolled strips for overlay welding:

Thickness 0.50 ± 0.035 mm

Width 30 - 180 ± 0.2 mm




CuNi8

CuNi10 2.0811 / C70700 DIN 17471

CuNi15

CuNi20 CN104 / C71000 BS 2870

CuNi30 C71580

CuNi44Mn1 2.0842 / N04401 / C72150 DIN 17664

CuNi10Fe1Mn CW352H / C70600 EN 1652 / ASTM B122

CuNi30Mn1Fe CW354H / C71500 EN 1652 / ASTM B122

1. Alloys


Alloy Ni (+Co) Cu Fe Mn C

CuNi8 < 8.0 balance < 0.1 < 0.3

CuNi10 < 11.0 balance < 0.1 < 0.3

CuNi15 14.0 - 16.0 balance < 0.3 < 0.5

CuNi20 19.0 - 20.0 balance < 0.2 < 0.5

CuNi30 29.0 - 32.0 balance < 0.5 < 0.3 < 0.1

CuNi44Mn1 43.0 - 45.0 balance < 0.5 0.5 - 2.0 < 0.1

CuNi10Fe1Mn 9.0 - 11.0 balance 1.0 - 1.8 0.5 - 1.0 < 0.1

CuNi30Mn1Fe 30.0 - 32.0 balance 0.4 - 1.0 0.4 - 1.0 < 0.1

Copper-Nickel-Alloys

Alloy Density Specific electrical resistivity at 20 °C

Average linear thermal expansion coe#cient

20 °C - 100 °C

Thermal conductivity at

20 °C

g /cm3 Ω • mm2/ m 10-6/K W/m • K

CuNi8 8.9 0.125 16 75

CuNi10 8.9 0.15 16 59

CuNi15 8.9 0.21

CuNi20 8.9 0.265 15 49

CuNi30 8.9 0.37 15 39

CuNi44Mn1 8.9 0.49 13.5 22

CuNi10Fe1Mn 8.9 0.17 17 48

CuNi30Mn1Fe 8.9 0.37 16 25


01/1

7




Alloy 0.2 % Yield strength Tensile strength Elongation Vickers hardness

MPa MPa % HV

CuNi8 100 260 45 max. 80

CuNi10 115 270 45 max. 85

CuNi15 140 300 45 max. 85

CuNi20 150 330 40 max. 85

CuNi30 150 330 40 max. 85

CuNi44Mn1 200 460 30 max. 115

CuNi10Fe1Mn 150 340 40 max. 120

CuNi30Mn1Fe 180 400 45 max. 120


Thickness Width 10 - 320

0.10 - 0.20 +/- 0.020

> 0.20 - 0.40 +/- 0.030

> 0.40 - 0.50 +/- 0.040

> 0.50 - 0.80 +/- 0.050

> 0.80 - 1.20 +/- 0.060

> 1.20 - 1.80 +/- 0.080

> 1.80 - 2.50 +/- 0.090

> 2.50 - 3.00 +/- 0.100


10 - 50 + 0.2 + 0.3 + 0.5 + 1.0

> 50 - 100 + 0.3 + 0.4 + 0.6 + 1.1

> 100 - 200 + 0.4 + 0.5 + 0.7 + 1.2

> 200 - 320 + 0.6 + 1.0 + 1.2 + 1.5

Length (in mm)



0.40 - 2.00 + 10


Coil 0.10 - 2.50 10 - 320 300 / 400 / 500 max. 1050

Strip / Sheet 0.40 - 2.00 50 - 320 500 - 3000






NiCu30Fe 2.4360 / N04400 DIN 17743 / ASTM B127

NiCu30Al 2.4375 / N05500 DIN 17743

NiCu45 N04404 ASTM F96

1. Alloys


Alloy Ni (+Co) Al C Cu Fe Mn Si Ti

NiCu30Fe

min. 63 28 1.0

max. 0.5 0.15 34 2.5 2.0 0.5 0.3

NiCu30Al

min. 63 2.2 27 0.5 0.3

max. 3.5 0.2 34 2.0 1.5 0.5 1.0

NiCu45

min. 54.5

max. 55.5 0.05 0.1 balance 0.3 0.1 0.1

Nickel-Copper-Alloys


Alloy Density Average linear thermal expansion coe"cient

20 °C - 100 °C

Curietemperature

Thermal conductivity at 20 °C

g/cm3 10-6/K °C W/m • K

NiCu30Fe 8.8 14 50 26

NiCu30Al 8.5 13.7 135 19

NiCu45 8.9 13 21

01/1

7




Alloy Condition 0.2 % Yield strength Tensile strength Elongation Vickers hardness

NiCu30Fe

MPa MPa % HV

soft annealed 250 550 40 120

hard 860 5 210

NiCu30Al

soft annealed 340 720 35 170

hard 750 - 1100 850 - 1250 1 - 8 250 - 350

NiCu45 soft annealed 160 450 45 120



0.10 - 0.20 +/- 0.010 +/- 0.015 +/- 0.015

> 0.20 - 0.30 +/- 0.015 +/- 0.015 +/- 0.020

> 0.30 - 0.50 +/- 0.020 +/- 0.020 +/- 0.025

> 0.50 - 1.00 +/- 0.025 +/- 0.025 +/- 0.030

> 1.00 - 1.50 +/- 0.030 +/- 0.040 +/- 0.040

> 1.50 - 2.00 +/- 0.040 +/- 0.040 +/- 0.050

> 2.00 - 2.50 +/- 0.050 +/- 0.050 +/- 0.060


10 - 100 + 0.2 + 0.3 + 0.5

> 100 - 200 + 0.3 + 0.5 + 0.7

> 200 - 320 + 0.6 + 1.0 + 1.2

Length (in mm)

Width Length 500 - 3000

0.40 - 2.00 + 10



Coil 0.10 - 2.50 10 - 320 300 / 400 / 500 max. 1050

Strip / Sheet 0.40 - 2.00 50 - 320 500 - 3000





Clad Materials

05 / 1

7

Characteristics

Clad material consist of at least one base material and a clad material, which are joined together by cold rolling.

In this way, the positive properties of the di"erent metals can be combined. The deliveries are possible in soft,

thermoformable or cold-strengthened conditions, depending on the intended use. Test criteria can be the yield

strength, the tensile strength, the elongation, the hardness, the formability, the grain size, in special tests, the

electrical resistance and the flare. Other properties by arrangement.

Samples of two layer and three layer

Material Options

Copper Cu-PHC, etc.

Nickel Ni99,2 / LC-Ni 99 / LC-Ni 99,6, etc.

Yellow brass CuZn10 / CuZn37 / CuZn25, etc.

Bronze CuSn6, etc.

Alloys Nickel, Iron-Nickel, Copper Alloys

Stainless Steel 1.4301 / 1.4306 / 1.4310 / 1.4541 / 1.4404 / 1.4512 / 1.4521 / 1.4571, etc.

Steel DC04 / DD11 / DD14 / C10, etc.

You will find the range of material options online.

On www.clad-configurator.de you can create your individual cladding strip with up to five layers in di"erent thickness ratios.

After configurating a cladding strip, the server calculates within seconds the associatedmaterial properties, such as mechanical, chemical and physical data. You can send these data via an online formular to your own email address.



Dimensions and tolerances: Thickness & Width (in mm)

Thickness Width < 250 Width > 250 - 300

normal normal

< 0.20 +/- 0.015 +/- 0.013 +/- 0.020 +/- 0.015

> 0.20 - 0.30 +/- 0.020 +/- 0.015 +/- 0.030 +/- 0.020

> 0.30 - 0.50 +/- 0.025 +/- 0.020 +/- 0.040 +/- 0.030

> 0.50 - 0.80 +/- 0.030 +/- 0.025 +/- 0.050 +/- 0.035

> 0.80 - 1.00 +/- 0.035 +/- 0.030 +/- 0.050 +/- 0.035

> 1.00 - 1.50 +/- 0.040 +/- 0.030 +/- 0.060 +/- 0.040

> 1.50 - 1.80 +/- 0.045 +/- 0.035 +/- 0.070 +/- 0.050

> 1.80 - 2.50 +/- 0.050 +/- 0.040 +/- 0.080 +/- 0.060

> 2.50 - 3.00 +/- 0.060 +/- 0.050 +/- 0.090 +/- 0.070

Width Thickness < 0,40 Thickness > 0,40 - 1,50 Thickness > 1,50 - 2,00 Thickness > 2,00 - 3,00

< 125 + 0.3 + 0.4 + 0.6 + 0.8

> 125 - 250 + 0.4 + 0.6 + 0.8 + 1.0

> 250 - 300 + 0.6 + 0.8 + 1.0 + 1.2

Thickness Width 500 - 3000

0.40 - 2.00 + 10

Length (in mm)

Delivery forms (in mm)


Coil 0.10 - 3.00 10 - 300 300 / 400 / 500 max. 1050

Strip 0.40 - 2.00 50 - 300 500 - 3000

Important Note: All data in this Material Data Sheet are only for information purposes. Other dimensions

and features to customer specification on request. Guarantees relating to specific characteristics or purposes

require always a special written agreement.

The strips receive a cold-rolled or brushed surface depending on the requirements of the customers.

The surface can also be oiled.

Clad Materials

Surface finish

Thermostatic Bimetals 1. Materials and Properties

Grade Spec. Thermal

Curvature20 °C - 130 °C

10-6/K

Specific Thermal

Deflection20 °C - 100 °C

10-6/K

Special Electrical

Resistivityat 20 °C

Ω • mm2/ m

Linearity Range

°C

Max. Operating

Temperature °C

Cladding Layer

on high exp. side

High Expansion Side

Intermediate Layer

Low Expansion

Side

Cladding Layer on low exp.

side

1 TB 230/110 43.0 ± 5 % 22.5 1.08 ± 5 % +20 to 230

350 none

MnNi16Cu10 none FeNi32Co6

none

2 TB 208/110 39.0 ± 5 % 20.8 1.10 ± 5 %

-20 to 200

MnCu18Ni10 none

FeNi36

3 TB 200/80 38.9± 5 % 20.8 0.82 ± 5 %

MnNi16Cu10

FeNi36/Ni

4 TB 200/60 38.8 ± 5 % 20.6 0.58 ± 5 % FeNi36/Ni

5 TB 200/60Fe 38.8 ± 5 % 20.6 0.58 ± 5 % Fe

6 TB 200/40 38.5 ± 5 % 20.5 0.40 ± 5 % FeNi36/Ni

7 TB 200/40Cu 38.5 ± 5 % 20.5 0.40 ± 10 % MnCu18Ni10 Cu

8 TB 200/40Fe 38.5 ± 5 % 20.5 0.40 ± 5 % MnNi16Cu10 Fe

9 TB 200/30 38.6 ± 5 % 20.3 0.30 ± 7 %

MnCu18Ni10

Cu

10 TB 200/25 38.6 ± 5 % 20.3 0.249 ± 7 % Cu

11 TB 200/20 38.5 ± 5 % 20.2 0.21 ± 7 % Cu

12 TB 200/17 38.4 ± 5 % 20.1 0.166 ± 7 % Cu

13 TB 200/15 38.4 ± 5 % 20.1 0.15 ± 7 % Cu

14 TB 200/11 37.8 ± 5 % 20.1 0.11 ± 7 % Cu

15 TB 200/10 37.5 ± 5 % 20.0 0.10 ± 7 % Cu

16 TB 185/08 37.5 ± 5 % 19.4 0.08 ± 10 % Cu

17 TB 180/05 33.8 ± 5 % 17.9 0.048 ± 10 % Cu

18 TB 175/05 32.4 ± 5 % 17.5 0.05 ± 10 % Cu

19 TB 170/03 31.6 ± 5 % 16.2 0.033 ± 15 % MnNi16Cu10 Cu FeNi32Co6

20 TB 140/140 28.4 ± 5 % 14.6 1.40 ± 5 % MnNi16Cu10 none

FeNi36

21 TB 140/135 28.5 ± 5 % 14.7 1.35 ± 5 % MnCu18Ni10 none

22 TB155/78 28.5 ± 5 % 15.5 0.78 ± 5 %

450

FeNi20Mn6 none

23 TB155/78B 28.5 ± 5 % 15.5 0.78 ± 5 % X60Ni14Mn7 none

24 TB150/78 27.6 ± 5 % 14.9 0.78 ± 5 % FeNi20Mn6 none

Grade Spec. Thermal


10-6/K

Specific Thermal


10-6/K

Special Electrical


Ω • mm2/ m

Linearity Range

°C

Max. Operating Tempera-

ture °C

Cladding Layer

on high exp. side

High Expansion Side

Intermediate Layer

Low Expansion

Side


side

25 TB145/78 26.9 ± 5 % 14.5 0.78 ± 5 %

-20 to 200

4500

none ine

FeNi20Mn6

none

FeNi36 none

26 TB140/78 26.4 ± 5 % 14.2 0.78 ± 5 % none

27 TB150/55 28.2 ± 5 % 15.0 0.55 ± 5 % Ni

28 TB150/55Fe 28.2 ± 5 % 15.0 0.55 ± 5 % Fe

29 TB150/50 28.0 ± 5 % 14.9 0.50 ± 5 % Ni

30 TB150/50Fe 28.0 ± 5 % 14.9 0.50 ± 5 % Fe

31 TB150/45 28.0 ± 5 % 14.9 0.45 ± 5 % Ni

32 TB150/45Fe 28.0 ± 5 % 14.9 0.45 ± 5 % Fe

33 TB148/35 27.4 ± 5 % 14.8 0.35 ± 5 % Ni

34 TB144/30 26.8 ± 5 % 14.4 0.30 ± 5 % Ni

35 TB140/25 26.1 ± 5 % 14.0 0.25 ± 5 % Ni

36 TB150/19 28.2 ± 5 % 15.0 0.19 ± 7 %

400

400

Cu

37 TB150/17 28.2 ± 5 % 15.0 0.17 ± 7 % Cu

38 TB150/15 28.1 ± 5 % 15.0 0.15 ± 7 % Cu

39 TB150/11 27.8 ± 5 % 15.0 0.11 ± 7 % Cu

40 TB145/11 26.9 ± 5 % 14.5 0.11 ± 7 % Cu

41 TB130/09 27.0 ± 5 % 14.2 0.09 ± 7 % Cu

42 TB130/06 26.2 ± 5 % 13.9 0.060 ± 10 % Cu

43 TB136/06 25.8 ± 5 % 13.6 0.059 ± 10 % 275 Cu none

44 TB132/03 24.6 ± 5 % 12.7 0.033 ± 15 % 275

none

Cu

45 TB130/03 24.6 ± 5 % 12.7 0.030 ± 15 % 300 Cu

46 TB147/79 27.7 ± 5 % 14.7 0.79 ± 5 %

-20 to 175 450

FeNi22Cr3

none

47 TB140/80 27.6 ± 5 % 14.0 0.80 ± 5 % none

48 TB140/66 26.4 ± 5 % 14.0 0.668 ± 5 % Ni

49 TB140/58 26.4 ± 5 % 14.0 0.582 ± 5 % Ni

50 TB139/50 26.4 ± 5 % 14.0 0.500 ± 5 % Ni

51 TB139/50Fe 26.3 ± 5 % 14.0 0.500 ± 5 % Fe

52 TB138/42 26.3 ± 5 % 13.9 0.417± 5 % Ni

Grade Spec. Thermal


10-6/K

Specific Thermal


10-6/K

Special Electrical


Ω • mm2/ m

Linearity Range

°C

Max. Operating Tempera-

ture °C

Cladding Layer

on high exp. side

High Expansion Side

Intermediate Layer

Low Expansion

Side


side

53 TB138/42Fe 26.1 ± 5 % 13.9 0.417± 5 %

-20 to 175

450

none

FeNi22Cr3

Fe

FeNi36

none

54 TB134/33 25.7 ± 5 % 13.5 0.332 ± 5 % Ni

55 TB130/29 25.3 ± 5 % 13.3 0.291 ± 5 % Ni

56 TB127/25 24.4 ± 5 % 13.0 0.245 ± 5 % Ni

57 TB127/25Cu 24.4 ± 5 % 13.0 0.245 ± 7 % 400 Cu

58 TB119/21 23.2 ± 5 % 12.2 0.208 ± 7 % 450 Ni

59 TB100/17 20.4 ± 5 % 10.7 0.166 ± 7 % 450 Ni

60 TB138/17 26.3 ± 5 % 13.8 0.161 ± 7 %

400

Cu

61 TB138/15 26.6 ± 5 % 14.1 0.150 ± 7 % Cu

62 TB137/12 26.2 ± 5 % 13.7 0.116 ± 7 % Cu

63 TB137/10 26.1 ± 5 % 13.6 0.097 ± 7 % Cu

64 TB135/08 25.9 ± 5 % 13.5 0.083 ± 10 % Cu

65 TB134/07 25.6 ± 5 % 13.4 0.066 ± 10 % Cu

66 TB131/06 25.5 ± 5 % 13.4 0.058 ± 10 % Cu

67 TB128/05 24.9 ± 5 % 13.0 0.050 ± 10 % Cu

68 TB124/04 24.7 ± 5 % 12.9 0.041 ± 10 % Cu

69 TB121/03 22.9 ± 5 % 12.0 0.033 ± 15 % Cu

70 TB64/02 12.6 ± 5 % 6.7 0.025 ± 15 % 300 Cu

71 TB150/74 28.0 ± 5 % 15.1 0.74 ± 5 % 0 to 300

450

FeNi20Mn6 none FeNi38

72 TB135/78 25.1 ± 5 % 13.5 0.78 ± 5 %

0 to 320

FeNi20Mn6 none

FeNi39

73 TB135/78B 25.5 ± 5 % 13.5 0.78 ± 5 % X60Ni14Mn7 none

74 TB125/09 25.0 ± 5 % 13.4 0.09 ± 7 % 400

FeNi22Cr3

Cu

75 TB124/09 24.0 ± 5 % 12.9 0.09 ± 7 % 400 Cu

76 TB134/75 25.5 ± 5 % 13.4 0.75 ± 5 % 70 to 230

450

none

77 TB131/42 25.1 ± 5 % 13.3 0.416 ± 5 %

-20 to 250

Ni

78 TB130/33 24.9 ± 5 % 13.0 0.332 ± 5 % Ni

79 TB128/29 24.4 ± 5 % 12.8 0.291 ± 5 % Ni

80 TB118/21 22.7 ± 5 % 11.9 0.208 ± 7 % Ni

Grade Spec. Thermal


10-6/K

Specific Thermal


10-6/K

Special Electrical


Ω • mm2/ m

Linearity Range

°C

Max. Operating

Temperature °C

Cladding Layer

on high exp. side

High Expansion Side

Intermediate Layer

Low Expansion

Side


side

81 TB125/17 24.2 ± 5 % 12.7 0.166 ± 7 %

-20 to 250

400

none

FeNi22Cr3

Cu

FeNi39

none

82 TB131/15 25.1 ± 5 % 13.2 0.150 ± 7 % Cu

83 TB131/12 25.0 ± 5 % 13.1 0.116 ± 7 % Cu

84 TB130/08 25.0 ± 5 % 13.0 0.088 ± 7 % Cu

85 TB128/08 24.5 ± 5 % 12.8 0.083 ± 8 % Cu

86 TB125/07 23.8 ± 5 % 12.4 0.066 ± 8 % Cu

87 TB115/05 22.4 ± 5 % 11.7 0.05 ± 10 % Cu

88 TB115/70 22.0 ± 5 % 11.7 0.70 ± 5 %

-20 to 380

450 FeNi20Mn6 none

FeNi4289 TB115/70B 22.0 ± 5 % 11.7 0.70 ± 5 % 450 X60Ni14Mn7 none

90 TB115/09 21.6 ± 5 % 11.5 0.09 ± 7 % 400

FeNi20Mn6

Cu

91 TB110/70 21.0 ± 5 % 11.1 0.70 ± 5 % 450 none

92 TB110/09 20.7 ± 5 % 11.0 0.09 ± 7 % 400 Cu

93 TB113/69 21.4 ± 5 % 11.3 0.69 ± 5 %

90 to 320

450 FeNi22Cr3 none

94 TB98/72 18.5 ± 5 % 9.8 0.72 ± 5 % 500 FeNi22Cr8.5 none

95 TB81/66 15.3 ± 5 % 8.1 0.66 ± 5 % 120 to 370 540 FeNi22Cr8.5 none

FeNi4696 TB100/65 18.6 ± 5 % 10.0 0.65 ± 5 % -20 to 425 450 FeNi22Cr8.5 none

97 TB100/65R 17.0 ± 5 % 9.0 0.62 ± 7 % -20 to 425 450 CrNi-Steel FeNi20Mn6 none

98 TB180/108R 33.5 ± 5 % 17.5 1.08 ± 5 %

-20 to 200

350

FeNi22Cr3 MnCu18Ni10 none

FeNi36

99 TB103/138R 19.8 ± 5 % 10.3 1.38 ± 5 % FeNi22Cr3 MnCu18Ni10 none

100 TB135/91 25.5 ± 5 % 13.5 0.91 ± 5 % none

FeNi20Mn6

MnNi16Cu10

101 TB155/78R 27.5 ± 5 % 14.5 0.78 ± 5 %

450 CrNi-Steel

none

102 TB155/78RR 24.6 ± 5 % 13.0 0.75 ± 7 % -20 to 225 none Cr-Steel

103 TB60/20R 11.4 ± 5 % 6.0 0.20 ± 10 % -20 to 450

none

none Fe Ni

104 TB102/85 19.6 ± 5 % 10.2 0.85 ± 5 % -20 to 180 525 FeNi18Cr12 none FeNi31Co8Cr6

none 105 TB52/65 10.0 ± 7 % 5.2 0.65 ± 7 % -20 to 600 550 CrNi-Steel none Cr-Steel

106 TB103/81 19.4 ± 5 % 10.3 0.81 ± 5 % -20 to 300 350 MnNi16Cu10 none CuNi44Mn1

107 TB97/16 18.2 ± 5 % 9.8 0.16 ± 5 % -20 to 220 400 Ni none FeNi36

Thickness Width< 75

Width> 75 - 125

Width > 125 - 250

0.10 - 0.15 ± 0.010 ± 0.010 ± 0.020

> 0.15 - 0.25 ± 0.010 ± 0.015 ± 0.020

> 0.25 - 0.40 ± 0.015 ± 0.020 ± 0.025

> 0.40 - 0.60 ± 0.020 ± 0.025 ± 0.030

> 0.60 - 1.00 ± 0.025 ± 0.030 ± 0.040

> 1.00 - 1.50 ± 0.030 ± 0.040 ± 0.050

> 1.50 - 2.00 ± 0.050 ± 0.050 ± 0.060

Other thickness and tolerances on request.

Thickness Tolerances

< 0.2 ± 0.004

> 0.2 - 0.4 ± 2%

Thickness Tolerances (Snap disc strip)Thickness Tolerances

Width Tolerances

Width Thickness < 1.5

Thickness> 1.50 - 2.00

< 75 + 0.2 + 0.4

> 75 - 125 + 0.3 + 0.5

> 125 - 250 + 0.5 + 0.8


Length Tolerances (Cut Length)


Length> 1000 - 1300

0.60 - 2.00 + 10 + 1%



Form Thickness Width Length

Coil-ID Coil-OD

Strip 0.10 - 2.00 3 - 2.50 300 / 400 / 500 max. 1100

Cut length 0.60 - 2.00 8 - 250 500 - 3000

Snap disc strip 0.1 - 0.4 10 - 60 300 / 400 / 500 (on core)

(in mm) Other thickness and tolerances on request.

Product Forms / Delivery Forms

5. Dimension tolerances for tension-levelled strip

Straightness of strip edge in longitudinal direction (edge camber)

The allowed straightness deviation is stipula-

ted in DIN 1715 and measured on a test piece

having a length of 1.000 mm.

strip widthmm

max. deviation h from straight line

mm

< 10 nach Vereinbarung

> 10 to 25 5

> 25 to 40 3.5

> 40 to 125 2.5

> 125 2

Tighter edge camber tolerance can be

agreed.

Surface flatness in rolling direction (waviness)

The waviness is the ratio of wave height h to wa-

velength L and stipulated in DIN 1715.

Thickness s mm

Waviness h/L%

< 1.00 max. 3

> 1.00 max. 2

Surface flatness in rolling direction(coil set)

Coil set can be agreed. It can be confirmed in

rolling direction, in the opposite direction or

with a +/- tolerance. The test is carried out on a

300 mm long test piece hanging on a measuring

device.Surface flatness across strip width (cross curvature)

The cross curvature can be agreed depending

on strip width, strip thickness and material.

Edge Properties

The standard production route provides strip with low

burr slit edges. The burr must not exceed 10 % of the strip

thickness for material having a strip thickness up to 0.50

mm. For a thickness above 0.50 mm, the burr must not

exceed 0.050 mm in height. Deburred or rounded edges

can be agreed for a strip thickness of 0.5 to 1.5 mm.

The edge radius for rounded edges can be 10 % to 40 % of

the strip thickness with a minimum radius of 0.1 mm and

a maximum radius of 0.5 mm. The minimum edge radius

tolerance can be agreed and represents +/- 0.05 mm of

the nominal edge radius.

A permanent marking is applied to the high expansion

side of the strip, preferable by an etching process.

This marking must not a"ect the thermostatic bimetal

properties. If required, the marking can be embossed on

strip having a minimum thickness of 0.60 mm. Delivery

of strip marked on the low expansion side or without any

marking can be agreed specially.

6. Marking

7. Packaging

The correct form of packaging in chosen to ensure protection of the strip

quality. The strip is temporarily protected by an anti-corrosion oil.

Standard Continental Packing:

Pallet type (mm)

Ties

Individual coil wrapping

Intermediate layers

Stack height

Shrink-wrap

Labelling

Standard Sea Freight Packing:

Pallet type

Ties

Individual coil wrapping

Intermediate layers

Stack height

Shrink-wrap

Labelling

700 x 700, 800 x 800, 1000 x 1000, Euro pallet 800 x 1200

3 x plastic tie fastenings

none

cardboard disks

max. 600 mm included pallet

covering stack

each pallet

wooden crate

3 x plastic tie fastenings

corrosion protective paper

none

max. 600 mm incl. crate

sealing stack completely

each

Other packing as well as delivery on reels upon agreement.

All data contained in this document are for information purposes only.

Other properties can be engineered according to customer specifications.

Guarantees of specific characteristics or applications require special written

agreement. www.auerhammer.com

Portfolio Auerhammer :

› Clad Material› Thermostatic Bimetal › Sealing- and expansion alloys› Soft magnetic materials› strip matals› Temperature- and corrosions-resistant materials› welding consumables› Metallic Foils

Auerhammer Metallwerk GmbH

Hammerplatz 1

08280 Aue (Sachsen)

Telefon +49 3771 272-0

[email protected]

www.auerhammer.com

Contact

Nickel + Nickel-Alloys · Strip / sheet 0.40 - 2.00 50 - 320 500 - 3000 Thickness Length 500 - 3000...

Documents

Transcript of Nickel + Nickel-Alloys · Strip / sheet 0.40 - 2.00 50 - 320 500 - 3000 Thickness Length 500 - 3000...