Operation Manual 4350 Paper Cutter

7/31/2019 Operation Manual 4350 Paper Cutter

1/44

IDEAL 4315

IDEAL 4350

GB Operating InstructionsGuillotines
http://www.whitakerbrothers.com/cutters/triumph-4350-paper-cutter


2/44

IDEAL 4315 IDEAL 4350

- 2-

D Bitte lesen Sie vor Inbetriebnahme der Maschine unbedingt diese Betriebsanleitungund beachten Sie die Sicherheitshinweise. Die Betriebsanleitung muss jederzeitverfgbar sein.

GB Please read these operating instructions before putting the machine into operationand observe the safety precautions. The operating instructions must always beavailable.

F Nous vous prions de lire attentivement le mode demploi avant dutiliser la machine,et attirons votre attention sur les consignes de scurit. Les instructions d'utilisationet les consignes de scurit doivent toujours tre disponibles. Les instructionsd'utilisation et les consi.

NL Leest u voor de ingebruik name van het apparaat a.u.b. deze gebruiksaanwijzinggoed door en neemt u de veiligheidsinstructies n acht. De gebruiksaanwijzing ende veiligheids-voorschriften moeten altijd binnen handbereik zijn.

I Per favore legga questo manuale di istruzione prima di mettere in funzione ildistruggidocumenti e osservi le regole di sicurezza. Le istruzioni duso devonoessere sempre disponibili.

E Le recomendamos lea las instrucciones antes de poner en funcionamiento estamquina y cumpla las normas de seguridad. Las instrucciones de servicio yseguridad deben estar siempre disponibles.

S Ls igenom denna bruksanvisning innan ni startar maskinen. Var noga medskerhetsfreskrifterna. Instruktionsmanualen mste alltid finnas tillgnglig.

FIN Lue nm kytt-ohjeet lpi ennenkuin kynnistt laitteen !Noudata turvaohjeita. Kyttohjeiden on oltava aina saatavilla.

N Lees gjennom denne bruksannvisningen fr De tar i bruk maskinenVr oppmerksom p sikkerhetsforskriftene. Opperatrmanualenm alltid vre tilgjengelig.

PL Prosz uwanie przeczyta instrukcj obsugi przed uruchomieniem urzdzenia istosowa si do przepisw bezpieczestwa. Instrukcje obsugi muszbyzawsze dostpne.

RUS , , . .

H A gp zembe helyezse elott figyelmesen olvassa el a kezelsi utastst s tartsabe a biztonsgi elorsokat.Kezelsi utastsnak mindig elrhetonek kell lennie.

TR Ltfen makineyi altrmadan nce bu kullanma talimatlarn dikkatli bir ekildeokuyunuz ve belirtilen gvenlik nlemlerine uyunuz. Kullanma Talimatlarher zaman kullanma hazr olmaldr.

DK Fr installation af maskinen bedes De venligst lse brugervejledningenbrugervejledningen og vre opmrksom p sikkerhedsanvisningerne.Brugervejledningen skal altid vre tilgngelig.

CZ Prosm pette si instrukce k obsluze a dodrujte bezpenostn

upozornn. Nvod k obsluze mus bt vdy dostupn.P Por favor leiam o manual de instrues antes de colocar a mquina em operaoe vejam as precaues de segurana. As instrues de operao devero estarsempre disponveis.

GR . .

SLO Prosimo preberite navodila za uporabo ter upotevajte varnostna opozorilapreden zaenete naparavo. Navodila naj bodo vedno pri roki.

SK Starostlivo si pretudujte tento nvod na obsluhu pred uvedenm stroja doprevdzky a najm bezpecnostn predpisy. Drte tento nvod na obsluhu nadostupnom mieste.

EST Palun lugege enne masina kivitamist kesolevat kasutusjuhendit ning jrgigeohutusnudeid. Kasutusjuhend peab alati keprast olema.

CHI

UAE

Sicherheitshinweise


3/44- 3 -

D Keine Bedienung durch Kinder!GB Children must not operate the machine!F Pas dutilisation par un enfant!

NL Geen bediening door kinderen!I Non lasciare utilizzare il tagliacarte a bambini!E No dejar que la utilicen los nios!S Installera maskinen utom rckhll fr barn!

FIN Asentakaa laite lasten ulottumattomiin !N Installer maskinen utenfor rekkevidde for barn!PL Dzieciom nie wolno obsugiwa urzdzenia !

RUS !H Gyerekek a gpet nem kezelhetik

TR Makinay ocuklar Kullanmamaldr.DK M kun betjenes af voksne

CZ Stroj nesm bt obsluhovn dtmi!P As crianas no devem trabalhar com a mquina!

GR .SLO Otroci ne smejo uporabljati napraveSK So strojom nesm pracovat deti!EST Lapsed ei tohi masinat kasutada!CHIUAE

D Nicht unter das Messer fassen!GB Do not reach beneath the blade!F Ne pas passer les mains sous la lame!

NL Niet met de handen onder het mes komen!I Non toccare la lama nella parte inferiore!E No tocar debajo de la cuchilla!S Strck inte in handen under kniven!

FIN l laita kttsi tern alle !N Plasser aldri hender ol. under kniven !PL Nie wkada rk pod noe!

RUS !H Ne nyljon a ks al!TR Elinizi ban altna sokmaynz!DK Stik ikke hnderne ind under knivbladet!CZ Nesahejte pod ost noe!P No tocar na parte inferior da faca!

GR !SLO Ne segajte z roko pod rezilo!SK Nevkladajte ruky pod n!EST rge pange ktt tera alla!CHIUAE

Sicherheitshinweise


4/44- 4 -


Sicherheitshinweise

D Messer nie lose liegen lassen!Messer nur mit Messerwechselvorrichtung oder imMessertransportkasten befrdern!

(siehe Seite 26 und 28).Warnung! Verletzungsgefahr!GB Never leave the blade unattended!

Do not extract or transport the blade without protection!(See page 26 and 28).

Danger!Risk of injury!F Ne jamais laisser la lame sans protections !

Elle ne doit tre dmonte qu l aide du dispositif dechangement de lame (cf. page 26 et 28, ou transporte dansson tui en bois !

Danger! Risques de coupures !

NL Laat nooit de messen alleen achter.Transporteer de messen niet zonder de houten bescherming(zie pagina 26 en 28).

Waarschuwing! Opgelet voor ongevallen!I Non lasciare mai la lama incustodita. Non rimuovere o

trasportare la lama senza protezione. (Vedi pagina 26 e 28).Attenzione!Rischio di infortunio!

E No quitar la cuchilla sin prestar atencin. No desmontar notransportar la cuchilla sin proteccin! (vrase pg. 26 y 28)

Advertencia! Peligro de hacerse dao!S Lmna aldrig maskinen obemannad. Ta inte ur eller

transportera kniven utan skydd. (se sid 26 och 28). Skaderisk!

FIN Ksittele ter aina varoen. l siirr tai kuljetater ilman suojaa ! (katso sivu 26 ja 28)

Loukkaantumisen vaara !N La aldri kniven ligge ubeskyttet. Ta aldri ut kniven eller

transporter den uten beskyttelse (Se side 26 og 28)FARE !Muligheter for skade !

PL Nidy nie pozostawia noy bez nadzoru! Nie wyciga lubtransportowa noy bez oson!

(zobacz strona 26 i 28).Ryzykoskaleczenia sisisisisi!RUS !

!(. 26 28)

! ! ! ! !

H Soha ne hagyja a kst rizetlenl!Ne vegye ki vagy ne szlltsa a kst vdtok nlkl!(Lsd 26. s 28. oldal)

Veszly!Srlsveszly!TR Ba hibir zaman gzetimsiz brakmaynz!

Ba muhafazasz olarak yerinden kartmaynz veyatamaynz! (Sayfa 26 ve 28e baknz)Dikkat! Yaralanma riski!


5/44- 5 -

DK Knivbladet m aldrig efterlades uden opsyn.Forsg ikke at afmontere eller transportere knivbladet udenbeskyttelse! (Se side 26 og 28)

FARE!Risiko for legemlig beskadigelse.CZ Nikdy nenechvejte n bez krytu.Nikdy nevyjmejte nebo neprepravujte nuz bez ochrannhokrytu (viz. strany 26 a 28)

Nebezpec!Riskujete zranenP Deixar a faca sempre em local seguro!

No retirar ou transportar a faca sem proteco!(Ver pg. 26 e 28)

Perigo! Risco de dano!GR !

( 26 & 28) ! !

SLO Nikoli ne puajte rezila nazaitenega. Nikoli ne prenaajterezilo brez zaite. ( glej stran 26 in 28).

Pozor!Pozor!Pozor!Pozor!Pozor! Nevarnost pokodbe.Nevarnost pokodbe.Nevarnost pokodbe.Nevarnost pokodbe.Nevarnost pokodbe.SK Nenechvajte n nechrnen (nezabezpecen)!

Nevyberajte alebo netransportujte n bez ochrany(vid s. 26 a 28)

! Riziko razu !! Riziko razu !! Riziko razu !! Riziko razu !! Riziko razu !EST rge jtke liketera kunagi jrelevalveta!

rge pikendage ega teisaldage tera kaitseseadmeteta!(Vt lk 26 ja 28)

Oht!Vigastuste oht!CHI

UAE2628

26

Sicherheitshinweise


6/44- 6 -


D Keine harten und splitternden Materialien schneiden!GB Do not cut hard materials or materials which may splinter!F La coupe de matriaux trop durs ou risquant des projections

est interdite !NL Snij geen harde materialen of materiaal dat kan splinteren!I Utilizzare il tagliacarte esclusivamente per il taglio di risme

di carta o materiali analoghi!E No cortar materiales duros o materiales que puedan

astillarse!S Frstr inte hrt material eller material som kan splittras!

FIN Asentakaa laite lasten ulottumattomiin !N Ikke kutt hardt metall eller materiale som kan splintre !PL Nie ci twardych materiaw lub materiaw, ktre mog

ulec odpryniciu!

RUS , !

H Ne vgjon kemny vagy olyan anyagot, amely repedhet!TR Sert veya paralanabilecek malzemeleri kesmeyiniz!DK Der m ikke skres i hrde materialer eller i materialer, der

kan splintre!CZ Neete tvrd materil, pi kterm mohou ustelovat ostr

lomky!P No cortar materiais duros ou materiais que possam lascar!

GR !

SLO Nikoli ne reite trdih materialov ali materialov, ki se lahkorazcepijo.

SK Nerete tvrd materily, alebo materily, z ktorch muvystrelovat ostr lomky.

EST rge ligake kvasid materjale ega materjale, mis vivadpilbasteks puruneda!

CHIUAE

Sicherheitshinweise


7/44- 7 -

The machine is designed for cutting stacks ofpaper to a specified size.This machine is constructed for "one-man

operation" only!Warning! Clips or similar damage thecutting blade.

Disconnect from the mains before starting anyservice work or before removing the panels!

Replacement of blade and cutting stick maybe performed only when the main switch isswitched off!

Safety precautions


8/44- 8 -


Safety precautions

All components which could endanger theoperator are covered by a guard!

Operating the machine without safety device isforbidden! Movable front safety guard (A) rear screwed safety guard (B) and cover (C)


9/44- 9 -

15mm

0.59inch

The dangerous cutting movement issafeguarded by a movable guard (A), rearscrewed safety guard (B) and a safety

two-handed control system! (C)

Before working with the machine and afterevery blade replacement the automatic cut-offfunction of safety guard (A),(correct if distancebetween cover and table is < 15 mm) mainswitch (B) and control panel (C) must bechecked.

Safety precautions


10/44- 10 -


230 V / 10A min120 V / 15A min

Protect mains cable against heat, oil andsharp edges!

Connect the power cord to a single phasesocket.

Ensure free access to mains

Safety precautions


11/44- 11 -

When not in use for a longer period switch off.(Main switch to "0").

Safety precautions

Clamping Blade

OK

OK

Danger!Do not turn main switch to position "0"whilst blade is moving upwards ordownwards!Risk of injury!

Danger! Blade must always be coveredby the pressing bar.


12/44


13/44- 13 -

Assembly of stand:2 strong people are required to lift themachine out of the packaging.

Lay the machine on the floor sidewards (1.). Remove the lower cover(2.) Place the cutter correctly onto the machine

stand. Fit the 4 washers and tighten the4 hexagon nuts with a spanner (3.).

Screw on the lower cover(4.) Install the machine.

Installation


14/44- 14 -


Plug into socket.

Installation

Screw on the backgauge crank (A).Screw on the handle (B) (only IDEAL 4315)found in the tool set (C).


15/44- 15 -

It is forbidden to operate the machine if theoperating and safety instructions have not beenunderstood. Please check the safety devices

are functioning and complete before use. All covers have to be mounted (A). The release for cutting is allowed only if

the cover is closed and the two-handsafety device is operated at the same time (B).

The front cover should not close byitself. Tighten the hexagonal recessscrew right (C).

We recommend you keep a record of your testresults.

Operation


16/44


17/44- 17 -

Operation

The measurement is set with the backgaugecrank.(A) The symbol rotary direction

moves to the right on the display (B) (see

picture C). The rotary direction of thebackgauge crank (A) is indicated on the right.Keep turning the backgauge crank to the rightuntil a measurement appears (see picture E).The reference position is reached.The cutting size can now be set with thehandle (A).If the backgauge is right at the front thesymbol rotary direction will move to theleft (see picture D). Turn the backgauge crankto the left until the rotary direction appears on

the right in the display (see picture C).Afterwards turn the backgauge crank to theright until a measurements appears (seepicture E). The reference position is reached.The cutting size can now be set with thehandle (A). Proceed to position from therear.

Measurement is shown on the display in inchesor cm (B).

Information:When the machine is only switched off by theKey switchG (main switch E is still ON) it isnot necessary to advance to the referencepoint when a new measurement is inserted.


18/44- 18 -


Optical cutting red line (A). Blade cuts on thefront edge (B) of the light beam.(Only use when no exact cut is required).

Operation

Pull out the handle to avoid the measurementbeing wrongly adjusted.


19/44


20/44- 20 -


IDEAL 4315Before every cut the lever must be moved tothe left and tightened with light pressure.

IDEAL 4350The clamp moves automatically when cuttingis activated.

Cutting activation:Press both buttons of the two-handed controlsystem (A) simultaneously and keep thempressed until the paper is completely cut.

To interrupt or stop cutting:

To interrupt or stop cutting, releaseboth buttons (A) of the two-hand control.

Operation


21/44- 21 -

Operating elements

A - Front safety guard

B - Safety two-handed control system

C - Overload switch blade drive

D - Clamping

E - Main switch

F - Crank handle for backgauge setting

G - Key switch

H - Backgauge

I - Side lay left

J - Display cutting size (cm or inch)

K - Changeover cm/inch

L - Measuring unit (cm or inch)

Operation


22/44


23/44


24/44- 24 -


Blade and cutting stick replacement

If the cutting quality decreases: Check the cutting depth (see page 32). Check the cutting stick (see page 25).

Replace or grind the blade(see page 24 - 32).The blade cannot be ground if the bladeheight is less than 35 mm/1,38 inches. Anew blade must be used.Purchase the new blade from Krug &Priester, D -72336 Balingen only.The blade may only be ground by aqualified workshop or from themanufacturer Krug & Priester,D -72336 Balingen.

Danger! Risk of injury!The blade is extremely sharp. Do notextract or transport the blade withoutprotection. Changing the blade may only beperformed by trained staff.


25/44- 25 -

Turn the blade depth adjustment screw to theleft until it stops (screwdriver found intool set (A).


Cutting stick replacement : Lift the cutting stick by hand and pull

it out.(1.). If needed the cutting stick can be turned or

exchanged. (The cutting stick can be usedeight times). (2.).

Waring! The machine may only beoperated when the cutting sticks are

inserted!

After exchanging the cutting stick close theclamp by moving the clamp lever to the left(3) (only IDEAL 4315).


26/44- 26 -


Remove the remaining 3 screws (1.).Push the blade and blade changing tool (A) tothe right and lower to remove (2.)Place the blade into the blade carrier (B)and screw it into place (3.).


Position the main switch to "0" (1.)Open the safety guard (2.). Remove the 2 bladescrews on the elongated holes (3.). Then put

the blade changing tool (R) into place andfasten it to the blade (4.).


27/44- 27 -

Take the exchange blade carefully out of theblade box and screw it to the blade changingtool (A)

blade must be covered! (B).

Danger! Risk of injury!



28/44- 28 -



Place the blade to be exchanged, using theblade changing tool, into the blade carrierand push to the top and to the left.(1.)

(see picture A) while doing so push bothsprings back.It is only necessary to push back the springs ifa polished blade is to be exchanged.(see picture B).


29/44- 29 -

Push the blade changing tool to the top withyour hand (1.). First, lightly tighten the middleblade screw with your other hand (2.) and then

both blade screws left and right (3.). Removethe blade changing tool (R) (unscrew thegrips).


Lightly tighten the 2 blade screws on theelongated holes (1.).


30/44- 30 -


Close the clamp by moving the clamp lever tothe left (1.) Close the safety guard (2.) Lowerthe blade by pressing both cutting buttons (3.)

If the last sheet of paper is not completely cut,gradually turn the knob for blade-depthadjustment (A) turn to the right until thepaper is cut along the entire length.(1 turn = 1,5 mm)


Open the clamp by moving the clamp lever tothe right (1.).Remove all tools and distributepaper along the entire cutting length (2.).

Turn main switch to position "I" (3.).


31/44


32/44- 32 -


Paper cutting test. If the last sheet or severalsheets are not completely cut, gradually turnthe knob for blade depth adjustment (A)

turn to the right until the paper is cut alongthe entire length. Do not set too low as bladewill become blunt sooner.

Danger! Do not turn main switch toposition "0" whilst blade is movingupwards or downwards!Risk of injury!

Danger! Blade must always be coveredby the pressing bar (see picture below onthe left).

Clamping BladeOK

OK



33/44- 33 -

Maintenance work may only be performed bytrained staff.

Danger! Disconnect the mains beforestarting any service work or beforeremoving the cover.

Maintenance and cleaning

Safety testThe safety regulations are according to theregulations of the country where the cuttingmachine is operated. The manufacturerrecommends a safety check is made every 5years by an authorised service team.


34/44- 34 -


AB

F

Nr. 9003 233

Nr. 9001 828


Grease the backgauge (A) control weekly.(Use non-resinous grease).Grease the remaining parts (B) twice a year(see picture).

Danger! Disconnect the mains beforestarting any service work or beforeremoving the cover.Put the machine on its left side.

Danger! of tilting!Remove cover (C) and lower panel (D) (toolsin tool set). Remove remaining paper Grease the machineCheck the two joining bolts and

pushing bar for wear. (F). If necessary

inform your service personnel. Mount the machine.

= Greasing points on the machine.


35/44- 35 -

Machine does not function!

Is themachine plugged in?

Main switch to position "I"? (A)Control system activated? (B)

(Turn key to the right)Release a cut see page 20.

Possible malfuntions


36/44- 36 -


Machine turns off: Machine overloaded

Safety button (A) ejects.

Allow 1 minute cooling time and reset thesafety button (A). Machine blocked Blade is blunt

Eliminate the cause, and push the safetybutton (A).



37/44- 37 -


Does not cut through the last sheet: Turn or turn around the cutting stick (A),

readjust the blade by means of the blade

adjusting knob (B).(See page 32).

Poor cutting quality or blade stays in thepaper stack. change the blade (C) (see page 24 - 32).


38/44- 38 -



Motor runs but blade does not movedownwards. Security brake has been activated!

Inform the service team!None of the above mentioned methodshelped to solve the problem:Contact Service Team under www.ideal.de "Service"

[email protected]

Cut cannot be made. If cover is open:

close it.

If cover is closed:open and re-close it. (Security check).


39/44- 39 -

Accessories

Recommended Accessories:

Blade Nr. 9000 121

Cutting stick (6 pieces) Nr. 9000 221

Paper knock-up block Nr. 9000 520 1

Blade changing tool Nr. 9000 517 1

Cabinet Nr. 4215 1100

Stand Nr. 4205 1100

1 Included in delivery.


40/44- 40 -


A

Technical data: Power supply: 230V/50Hz/0,45KW,

120V/60Hz/0,45KW

Sound level: EN 13023: < 70 dB (A) Leakage current < 3,5mA Power cord gauge min. 1,5mm2 (230V) Power cord gauge AWG 18 (15A)(120V) Cutting height: 40 mm Cutting length: 430 mm Table depth: 435 mm Height/Weight:

1055 mm/88 kg with stand (IDEAL 4315)1080 mm/95 kg with cabinet (IDEAL 4315)1055 mm/95 kg with stand (IDEAL 4350)

1080 mm/113 kg with cabinet (IDEAL 4350)

The exact technical specifications can befound on the technical specifications sticker (A)on the machine. A wiring diagram is found inthe electrical switch box.To claim under guarantee, the machine muststill carry its original identification label.

Required space for operation, servicing and

maintenance.ca. 1200 mm x 1300mm x 1400 mm.(B xT x H)

Technical data


41/44- 41 -

Technical data

This machine is approved by independentsafety laboratories and is in compliance withthe EC-regulations 2006/42/EG, and

2004/108/EG.

Sound level information:The sound level is < 70 db (A) as defined byEN 13023.

Subject to alteration without notice.


42/44- 42 -


D EG-KONFORMITTSERKLRUNGGB EC-declaration of conformityF Dclaration de conformit CE

- Hiermit erklren wir, da die Bauart von- Herewith we declare that- Par la prsente, nous dclarons que

UL- IDENT. Nr.4315; 4350 ID Nr. 10431501

- folgenden einschlgigen Bestimmungen entspricht

- complies with the following provisons applying to it- sont conformes aux dispositions pertinentes suivantes

2006/42/EG:Maschinenrichtline, EC Machinery directive, EC Directives machines.2004/108/EG:EMV Richtline, EMV Electromagnetic compatibility directive,EMV directives compatibilit lectromagntique.

- Angewendete harmonisierte Normen insbesondere- Applied harmonised standards in particular- Normes harmonises utilises, notamment

EN 60204-1; EN 1010-1; EN 1010-3; EN 55014-1; EN 55014-2;EN 61000-3-2; EN 61000-3-3; EN ISO 12100-1; EN ISO 12100-2;EN ISO 13857; EN ISO 11204; EN 13023; EN ISO 13849-1.

29.12.2009Datum

Bevollmchtigter fr technische Dokumentation

Authorized representative for technical documentationReprsentant autoris pour la documentation technique

Krug & Priester GmbH u. Co KGSimon-Schweitzer-Str. 34D-72336 Balingen (Germany)


43/44- 43 -

Remarks:


44/44

Operation Manual 4350 Paper Cutter

Documents

Transcript of Operation Manual 4350 Paper Cutter