Standard - Fraunhofer ILT · Web viewIncredibly light and holds up in collisions – but often...

FRAUNHOFER INSTITUTE FOR LASER TECHNOLOGY ILT

Editorial NotesDipl.-Phys. Axel Bauer | Head of Marketing and Communications | Phone +49 241 8906-194 | [email protected] Nolis M.A. | Leader Communications Group | Phone +49 241 8906-662 | [email protected] Institute for Laser Technology ILT | Steinbachstraße 15 | 52074 Aachen, Germany | www.ilt.fraunhofer.deSteinbachstraße 15 | 52074 Aachen, Germany | www.ilt.fraunhofer.de

PRESS RELEASEOctober 1, 2014 || | 5

Joining ultra-high-strength chromium steels reliably with laser technology Incredibly light and holds up in collisions – but often impossible to weld: this characterizes ultra-high-strength chromium steels that, thanks to their high carbon content, could not be reliably bonded together by laser until now. At this year’s EuroBLECH, the International Sheet Metal Working Technology Exhibition, the Fraunhofer Institute for Laser Technology ILT will use a B-pillar to show how laser welding can be reliably used on press-hardened, martensitic chromium steels.

Within the scope of the research project SECOMAL, the Fraunhofer Institute for Laser Technology ILT in Aachen has determined process parameters and process windows for the laser welding of three ultra-high-strength chromium steels: pure ferritic, ferritic-martensitic, and pure martensitic with carbon content ranging from 0.02 to 0.46 mass percent. Hardened, they achieve a tensile strength of up to two gigapascals with fracture strain of 10 percent. Their inherent resistance to corrosion makes these steels ideal for vehicle manufacturing.

The materials with the lowest and the highest carbon content – ferritic and martensitic chromium steels, respectively – can now be easily joined, even when the materials are hardened. “Only the martensitic stainless grade 1.4021, with an average carbon content of 0.21 percent poses dfficulties,” says Dipl.-Ing. Martin Dahmen, a researcher of the Fraunhofer ILT.

According to the textbook, preheating martensitic steel is recommended before joining and then tempering it – that is, heating the welding zone locally – to improve the toughness in the heat-affected zone. Hardened sheets can be tempered up to 450°C without causing any loss of quality. In principle, all types of laser beams are suitable for welding materials, but since the laser should produce parallel seam edges, Dahmen recommends using only the so-called brilliant beam sources and CO2 lasers.

PRESS RELEASE




But how does the laser compare to metal active gas (MAG) welding? “With judicious heat treatment, the hardened chromium steel can be joined without difficulty, with the exception of 1.4021,” says the ILT researcher. “On the other hand, MAG welding is problematic because of the resulting high-energy input in the joining areas, even with appropriate heat treatment.”

What successful laser welding looks like in practice will be showcased by the Fraunhofer ILT on its test specimen of a B-pillar of ultra-high-strength steel welded to a vehicle rocker panel. “This proves that welding ultra-high-strength materials by laser offers a viable alternative to manganese-boron steels,” says Dahmen. Visitors to EuroBLECH 2014 can visit the demonstrator exhibit and learn more about laser welding chromium steels and other Fraunhofer ILT projects at the Fraunhofer Joint Stand in Hall 11, Booth C05.

SECOMAL joint research project

The focus of this research project is investigating how laser and MAG welding can be used for fusion welding ultra-high-strength stainless steels with a martensitic structure. SECOMAL is a collaborative research project of the Fraunhofer ILT and the Paderborn University Laboratory of Materials and Joining Technology (LWF), the Fraunhofer Institute for Structural Durability and System Reliability LBF, and the steelmaker Outokumpu Nirosta. It is funded by the German Federal Ministry for Economic Affairs and Energy (BMWi), the German Federation of Industrial Research Associations Otto von Guericke e.V. (AiF), and the Research Association for Steel Application (FOSTA).




Picture 1: Microstructure of weld in 1.4034. Picture Source: Fraunhofer ILT, Aachen, Germany.




Picture 2:At EuroBLECH 2014, Fraunhofer ILT will use a test specimen for B-pillars to demonstrate that laser welding can be used reliably on press-hardened, martensitic chromium steels. Picture Source: Fraunhofer ILT, Aachen, Germany.




The Fraunhofer-Gesellschaft is the largest organization for applied research in Europe. Its research activities are conducted by 67 Fraunhofer Institutes at numerous locations throughout Germany. The Fraunhofer-Gesellschaft employs a staff of more than 23,000, who work with an annual research budget totaling 2 billion euros. Of this sum, 1.7 billion euros is generated through contract research. More than 70 percent of the Fraunhofer-Gesellschaft’s contract research revenue is derived from contracts with industry and from publicly financed research projects. Affiliated research centers and representative offices around the world provide contact with regions of greatest importance to present and future scientific progress and economic development.

ContactDipl.-Ing. Martin Dahmen | Macro Joining and Cutting Group | Telephone +49 241 8906-307 | [email protected] Dr. Dirk Petring | Leader Macro Joining and Cutting Group | Telephone +49 241 8906-210 | [email protected] Institute for Laser Technology ILT, Aachen, Germany | www.ilt.fraunhofer.de

Dieses Feld, sowie die Tabelle auf der letzten Seite nicht löschen!

Standard - Fraunhofer ILT · Web viewIncredibly light and holds up in collisions – but often...

Documents

Transcript of Standard - Fraunhofer ILT · Web viewIncredibly light and holds up in collisions – but often...