testo 325 i

download testo 325 i

of 20

description

Brošura gasnog analizatora

Transcript of testo 325 i

  • Bedienungsanleitung

    Rauchgas-Analysegert

    testo 325-I

    SO2

    NO

    COlow

    COhigh

    Flue Gas Analyser

    Instruction manual

  • Betrieb ber Steckernetzteil Fr den Betrieb des Gertes nur das Original-Netzteil ver-wenden.

    DichtigkeitVor jeder Messung mu das komplette Messsystem (Sonde,Kondensatfalle, Schluche und Steckanschlsse) auf Dichtig-keit geprft werden z. B. durch Aufstecken einer zusammenge-drckten Gummiblase auf die Sondenspitze. Durch Ziehen vonFalschluft kann es zu Fehlmessungen kommen.

    GasausgangAchten Sie bei der Messung darauf, da der Gasausgang desAnalysegertes frei liegt, damit das Gas ungehindert ent-weichen kann. Ist das nicht der Fall, kann dies zu einerVerflschung der Messergebnisse fhren.

    KondensatfalleKondensatfalle sptestens bei Erreichen der Maximal-Linienentleeren. Die Pumpe mu ausgeschaltet sein (ansonstenbesteht Gefahr fr die Messzellen)!Messzellen In den Messzellen befindet sich eine geringe Menge konzen-trierter Sure bzw. Lauge. Diese Messzellen als Sondermllentsorgen.

    MessgertDas Aufbewahren der Messgerte in Rumen, in denenLsungsmittel gelagert werden, fhrt zur Zerstrung derMesszellen.

    Warnhinweise

    Inbetriebnahme

    3

    Vorwort.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Inbetriebnahme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

    Warnhinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Stromversorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Gasweg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Gerteabbildung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

    Messbeispiel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Abgasmessung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Ausdruck der Messergebnisse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Einstellen Datum/Uhrzeit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

    Wartung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Akku- oder Batteriewechsel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Kondensatfalle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Filterwechsel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Reinigen der Rauchgaspumpe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Messzellenwechsel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

    Fehlermeldungen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Zubehr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

    Testo-Protokolldrucker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Technische Daten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

    Querempfindlichkeiten. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Garantiebestimmungen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Bestelldaten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Testo weltweit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

    Liebe Testo-Kundin, lieber Testo-Kunde,

    Ihre Entscheidung fr den Kauf des testo 325-1 war richtig. Jedes Jahr kaufen tausende Kundenunsere hochwertigen Produkte. Dafr sprechen mindestens 7 gute Grnde:

    1) Bei uns stimmt das Preis-Leistungs-Verhltnis. Zuverlssige Qualitt zum fairen Preis.2) Deutlich verlngerte Garantiezeiten von bis zu 3 Jahren - je nach Gert!3) Mit der fachlichen Erfahrung von ber 40 Jahren lsen wir Ihre Messaufgabe optimal.4) Unser hoher Qualittsanspruch ist besttigt durch das Zertifikat nach ISO 9001.5) Selbstverstndlich tragen unsere Gerte das von der EU geforderte CE-Zeichen.6) Kalibrier-Zertifikate fr alle relevanten Messgren. Seminare, Beratung und Kalibrierung

    vor Ort.7) Auch nach dem Kauf lassen wir Sie nicht im Regen stehen.

    Unser Service garantiert Ihnen schnelle Hilfe.

    Inhalt

    Vorwort

    2

    Megert konform zu EN 61 326-1 Klasse B: 1997, EN 61326-1: 1997

  • Inbetriebnahme

    5

    Inbetriebnahme

    4

    Gasweg

    Gerteabbildung

    RG = Rauchgas

    Gaseingang

    AnschluNetzteil

    Stromversorgung

    Standard-Akkus oder Batterien- Standard-Akkutyp (1.5V IEC KR 15/51 entspr. Typ AA) oder

    Batterietyp (1.5V MIGNON Alkaline IEC LR6 AA ) verwen-den (4 Stck).

    Testo-Netzteil (0554.0054)- Auf guten Kontakt des Anschlusteckers im testo 325-I

    achten.- Betrieb ber Netzteil auch mit leeren Akkus/Batterien mglich.

    (Akkus nicht im Gert ladbar)

    Kapazittsanzeige

    Spannung >4,6 V (Standzeit ca. 3 h, bei einerUmgebungstemperatur von 20C)

    blinkendes Symbol, Spannung

  • 7Der Messwert wird ausgedruckt mit

    - Datum/Uhrzeit- Messeinheit

    (Einstellung Datum/Uhrzeit siehe Referenzteil)

    Aus dem Messmen kann der Ausdruck der Messwerte mit derTaste Drucken ausgelst werden. Ausdruck nur bei stehenderPumpe mglich. Druckvorgang abbrechen mit Taste ESC.

    testo 325-I07.09.1999 10:19:35

    SO2 1225 ppm

    Datum/Uhrzeit

    Mewert

    Mebeispiel

    Ausdruck der Meergebnisse

    6

    Messbeispiel

    AbgasmessungBeispiel: testo 325-I SO2

    3 sec. 3 sec. 60 sec.V 110

    6.0 43

    STARTSTOP

    STARTSTOP

    ppm0

    SO2

    Nach jeder Messung die Messzellen mit Frischluft splen (Pumpe Start/Stop) bis der CO-/NO-/SO2-Gehalt unter 50 ppm.

    Bei SO2-Messung auf trockene Gaswege achten!

    Sonde anschlieen

    Selbsttest Messmen

    Messmen

    Ausdruck

    Pumpeluft.

    Batterie-Kapazitt Nullungsphase

    testo 325-Ieinschalten

    ppm225

    SO2

    Messmen

    ppm225

    SO2

    Messmen

    ppm225

    SO2

    Messmen

    ppm225

    SO2CAL.

    STARTSTOP

    Mit Taste OK Einstellwert aktivieren.Mit Taste Rechts Einstellfeld wechseln.

    Mit Taste Oben Wert erhhen, mit Taste Unten Wert verringern.Mit Taste OK Einstellungen besttigen und Sprung insMemen.

    Mit Taste ESC zurck ins Hauptmen, keine bernahme derEinstellungen.

    15.031999

    03.151999

    14:15EinstellfeldblinktUmschalten

    aufUS-Format

    SymbolUhrzeitSymbol

    Datum

    Einstellen Datum/Uhrzeit

    OK

    OK

    DDAATT DAT

  • 9Kondensatfalle

    Filterwechsel

    Bei optisch erkennbarer Verschmutzung des Filters mu dieserausgetauscht werden.

    Dazu die Kondensatfalle entriegeln und vom Gehuse ent-fernen.

    Filter herausziehen und durch neuen ersetzen. Ersatzfilter(Best.-Nr. 0554.0040, 10er Pack) bestellen.Ausschlielich diesen Filter verwenden.

    Nach jedem Filterwechsel Dichtigkeitstest durchfhren (sieheSeite 3).

    Fllstandanzeige der Kondensatfalle nicht berschreiten.

    Zum Entleeren der Kondensatfalle Entleerungs-Stopfen heraus-ziehen.

    Leere/defekte Akkus bzw. leere Batterien aus dem Batteriefachentnehmen und durch neue Akkus oder Batterien ersetzen.

    Achtung!Auf richtige Polaritt der Akkus oder

    der Batterien achten!

    Vor Akku- oder Batteriewechsel das Gert ausschalten.

    Den Wechsel innerhalb von 1 - 2 Minuten durchfhrenoder Netzteil einstecken.Ansonsten droht der Ver-

    lust der eingestellten Werte Datum/Uhrzeit.

    Vor dem Filterwechsel

    Kondensatfalle entleeren.

    8

    Wartung Wartung

    Akku- oder Batteriewechsel Reinigen der Rauchgaspumpe

    Filter

    Fllstand-anzeige

    Kondensat-entleerung

    12

    3

    4

    m a x

    ma

    x

    Gehuse des Messgerts ffnen (siehe Seite 10, Punkte 1 -8).- Vorsichtig die Pumpe herausziehen.- Werkzeug Pump Tool in die Fhrungen des Pumpenkopfs

    stecken.- Werkzeug Pump Tool mit dem Pumpenkopf abnehmen.- Membranaufnehmer vom Pumpenkopf entfernen und

    Membrane entnehmen.- Pumpenmembrane, Pumpenteller und Pumpenkopf mit

    Spiritus oder Wasser reinigen.- Pumpenmembrane in den Membranaufnehmer einlegen und

    in den Pumpenkopf einfgen- Pumpenkopf auf die Pumpe aufsetzen.- Werkzeug Pump Tool entfernen.- Pumpe in den Montageblock einsetzen.- Messgert zusammensetzen (siehe Seite 11).

    PUMP

    TOOL

    Pumpe(Art.-Nr.0239.0015)

    Pumpenteller

    Pumpenkopf

    Pump Tool

    Pump Tool(Art.-Nr.0192.0468)

    Membrane(Art.-Nr.0193.0072)

    Membran-aufnehmer

  • 1110

    Wechsel der COlow-Messzelle

    Vor Einbau der neuen COlow-Messzelle die Kurzschluss-feder vorsichtig von den Kontakten entfernen.

    - Messzelle vom Messkammer-Deckel abziehen und neueMesszelle aufstecken.

    Kurzschlufeder

    COlow-Mezelle

    Wechsel der SO2-, NO-, COhigh-Messzelle

    - Die Messzelle befindet sich in der Messkammer. Messzelleentnehmen und neue Messzelle einsetzen. Beim Einbau aufdie Fhrungen an Messzelle und Messkammer achten.

    - Vor Einbau der neuen SO2-,NO-COhigh-Zellen die Kurz-schlussfeder vorsichtig von den Kontakten entfernen.

    Zusammenbau des testo 325-I

    - Messkammer-Deckel auf die Messkammer legen. Die Be-festigungsschrauben (3 Stck) anziehen.

    - Montageblock mit der Elektronik zusammenfgen.- Montageblock und Elektronik in das Gehuseoberteil legen.- Befestigen des Montageblocks und der Elektronik an das

    Gehuseoberteil mit den Halterungsschrauben (2Stck).- Gehuseunterteil aufsetzen und in entgegengesetzter Pfeil-

    richtung schlieen.Achtung: Flex-Leitung der Tastatur nicht einklemmen!

    - Fixierplatte einsetzen und Filter einstecken.- Kondsatfalle aufsetzen. Auf Einrastton achten.- Batterien/Akkus einlegen und mit Batteriefach-Deckel

    schlieen.

    - NO-Filter aus der Messkammer herausnehmen. Beim Ein-legen des neuen Filters darauf achten, da die Flche mitden Bohrungen nach unten in der Mekammer liegt.

    WartungCOlow-Messzellenwechsel

    Bei Wechsel einer COlow-Messzelle mu auch der NO-Filtererneuert werden.

    Vor Berhren der Elektronik elektrische Ladung des eigenenKrpers abbauen.

    Berhrungen der Elektronik vermeiden.

    Batteriefach-Deckel

    Kondensatfalle

    Fixierplatte

    MekammerCO low-Mezelle

    Befestigungsschrauben

    NO-Filter

    Filter

    MontageblockSO2-, NO-,CO high-Mezelle

    Mekammer-Deckel

    Platine

    Halterungsschrauben

    1.) Schlauchverbinder der Rauchgassonde, sowie das Netzteilvom testo 325-I abziehen.

    2.) Kondensatfalle vor dem Abziehen entleeren.3.) Kondensatfalle entriegeln und vom Gehuse entfernen4.) Filtereinsatz herausnehmen (siehe Seite 8).5.) Fixierplatte mit einem Schraubendreher entfernen.6.) Batteriefach ffnen und Batterien/Akkus entnehmen

    (siehe Seite 8).7.) Das Gehuse des testo 325-I wird durch Bewegen

    der Gehuseteile in Pfeilrichtung geffnet (siehe Skizze).

    8.) Gehuseunterteil abnehmen.9.) Halterungsschrauben lsen (siehe Skizze).

    10.) Montageblock mit der Elektronik aus dem Gehuseoberteil herausnehmen (siehe unten).

    11.) Montageblock von der Platine abziehen.12.) Befestigungsschrauben (3 Stck) des Mess-

    kammer-Deckels lsen. Deckel entfernen.

    Fixierplatte

    Gehuseunterteil

    Gehuseoberteil

    Halterungsschrauben

    Wartung

    Messzellenwechsel

  • 13

    FehlermeldungFehlermeldungen whrend des Mebetriebs

    blinkt

    Whrend der NullungsphaseSO2 D blinktNO D blinktCOlow D blinktCOhigh D blinkt

    Vor dem AusschaltenSO2 blinktNO blinktCOlow blinktCOhigh blinkt

    Nach dem Einschalten/NullungdphaseSO2 A blinktNO A blinktCOlow A blinktCOhigh A blinkt

    12

    Fehlermeldungen

    Ursache / Behebung

    Zulssige Betriebstemperatur ber- oder unter-schritten. Die Umgebungstemperatur ndert sichauf nicht zulssige Werte. Umgebungstempera-tur anpassen.

    Messung des Nullpunkts nicht stabil. Mehrmali-ges Durchlaufen der Nullungsphase abwarten.Bringt dies kein Erfolg ist die Messzelle ver-braucht.

    Im Gert befindet sich noch Rauchgas oder bei letzter Messung wurden sehr hohe Konzentra-tionen gemessen oder Nullungsphase verlngertsich.Ursache: Nach letzter Messung nicht gengend mit Frischluft gesplt oder Sonde befindet sich im Rauchgas. Sonde an Frischluft bringen. Wenn nach mehrmaligem Durchlaufen der Nullungsphasekeine nderung eintritt, liegt ein Zellendefektvor oder die Zelle ist verbraucht.

    Gerteversorgungsspannung wird zu niedrig.Akku laden/Batterie wechseln oder Netzteil anschlieen.

    Im Gert befindet sich noch Rauchgas oder bei letzter Messung wurden sehr hohe Konzentra-tionen gemessen oder Nullungsphase verlngertsich.Ursache: Nach letzter Messung nicht gengend mit Frischluft gesplt oder Sonde befindet sich im Rauchgas. Sonde an Frischluft bringen. Wenn nach mehrmaligem Durchlaufen der Nullungsphasekeine nderung eintritt, liegt ein Zellendefektvor oder die Zelle ist verbraucht.

    LOW BAT

    Eingabe SO2-, NO-, CO-Zellenkoeffizent

    Der Zellenkoeffizient befindet sich auf dem Beipackzettel derentsprechenden Ersatz-Messzelle.

    Nach Eingabe der Koeffizienten und Besttigen mit Taste OKerfolgt Sprung in die Nullungsphase.

    Whrend der Kalibrierphase kann jederzeit nach zweimaligemBettigen der Taste ESC in die Nullungsphase gesprungenwerden.

    Taste Drucken und Taste Rechts innerhalb 3 Sekundenwhrend der Kapazittsanzeige gleichzeitig gedrckt halten.

    Nachkalibrierung ber die Testo Service-Stellen, Tochtergesellschaften undVertretungen.

    SO2

    C

    25.5025.8

    Zahlenstelleauswhlen

    Zahlenwerterhhen

    Zahlenwertverringern

    3 sec.

  • 15

    testo 325-I

    Allgemeine technische Daten

    Max. Unterdruck im Abgas: 50 hPaGewicht: 500gAbmessungen: 216 x 68 x 47 mmTransport-/Lagertemperatur: -20...+50 CUmgebungstemp.: +4...+45 CStromversorgung: ber Stecker-Netzteil, Batterien

    oder austauschbare AkkusBatteriestandzeit: > 4 hGehusematerial: ABS

    Abgassonde

    Entnahmerohr: Lnge 300 mm, 6 mmEinsatztemperatur: max. + 500 CSchlauchlnge: 3 m (Tygon-Material bei

    SO2-Version)

    Technische Daten

    14

    testo 325-I testo 325-I testo 325-I testo 325-ISO2 NO CO low CO high

    Messbereich 0...3000 ppm 0...1000 ppm 0...2000 ppm 20...40.000 ppm

    Genauigkeit bis 400 ppm bis 400 ppm bis 400 ppm bis 800 ppm< 20 ppm < 20 ppm < 20 ppm < 40 ppm

    bis 2000 ppm 5% v. Mw.

    > 400 ppm > 200 ppm > 400 ppm >2000 ppm< 5% v. Mw. < 5% v. Mw. < 5% v. Mw. < 10% v. Mw.

    Einstellzeit t90 < 80 s < 60 s < 60 s < 70 s

    Auflsung 1 ppm 1 ppm 1 ppm 5 ppmab 10.000 ppm

    0.001 Vol. %

    Technische DatenDruckerart: . . . . . . .infrarotgesteuerter ThermodruckerBetriebstemperatur: . . . . . . . . . . . . . . . . . . .0...+50 CLager-/Transporttemp.: . . . . . . . . . . . . . . .-40....+60 CAbmessungen: . . . . . . . . . . . . . . . . .150 x 88 x 50 mmGewicht: . . . . . . . . . . . . . . . . . .0,33 kg (inkl. Batterien)Stromversorgung: . . . . . . . . .4 Mignon-Batterien 1,5 V

    oder NC-AkkusZubehr: . . . . . . . . . .Ersatzpapier Best.Nr. 0554.0569

    - Papiervorschub- Zurck aus Ruhemodus- Selbsttest = Taste beim

    Einschalten gedrckt halten

    bertragungsstrecke:

    Magnetplatte auf derGerte-Rckseite

    Achtung: Nach etwa 10-mintiger Inaktivitt schaltetder Drucker in einen Ruhemodus.

    Entsorgungshinweis:Entladene Batterien in Sammelbox werfen.Um Kurzschlssen vorzubeugen, Batterieneinzeln in Plastikbeutel geben.

    6060

    max. 2 m

    10

    20

    Kontrast einstellen

    EIN/AUS

    bedruck

    bare Seit

    e

    Datenempfang undEinschalt-Kontrolllampe

    grn = EIN/Batterie o.k.gelb = EIN/Batteriewarnungrot = EIN/Batterie leer

    Fenster nicht verschmutzen!

    I0

    Testo-Protokolldrucker 0554.0545

    Zubehr

    QuerempfindlichkeitenQuergas

    Modul CO NO SO2 NO2 H2S H2 CI2 HCI HCN CO2CO --- 0 0 0 0 0 0 0 0 0NO 0 --- 0

  • 16 17

    testo 325-I

    Bestelldaten

    Beschreibung Bestell-Nr.

    Gert

    Abgas-Analysegert testo 325-I (SO2) inkl. Batterien 0632.3260Abgas-Analysegert testo 325-I (NO) inkl. Batterien 0632.3261Abgas-Analysegert testo 325-I (COlow) inkl. Batterien 0632.3262Abgas-Analysegert testo 325-I (COhigh) inkl. Batterien 0632.3263

    Abgas-Sonden

    Abgas-Sonde (Lnge 300 mm, Tmax +500 C, SO2) 0600.7541Abgas-Sonde 0600.7542Konus fr Abgas-Sonde 0554.9050Abgas-Sonde (Lnge 700 mm, Tmax +1000 C) inkl. Spezialschlauch

    fr SO2-Messungen 0699.3451/3

    Drucker

    Testo-Protokolldrucker 0554.0545

    Zubehr

    Gerte SoftCase (zur Befestigung am Kessel) 0516.2570Gertekoffer (Kunststoffausfhrung) 0516.3250Netzteil (230 V fr Netzbetrieb) 0554.1084Netzteil GB 0554.0041Netzteil J 0554.0052Netzteil USA 0554.0053Ersatz-Schmutzfilter fr testo 325-I (10 Stck) 0554.0040Ersatz-Papier fr Protokolldrucker 0554.0569

    Ersatzzellen

    COlow-Ersatzzelle inkl. Filter 0390.0168COhigh-Ersatzzelle 0390.0142SO2-Ersatzzelle 0390.0143NO-Ersatzzelle 0390.0144

    Garantiebestimmungen

    Gert: 24 Monate Entnahmesonde: 12 MonateZubehr 6 MonateMesszellen 6 MonateDrucker 12 Monate (auer Druckwerk)

    Sehr geehrte Kundin, sehr geehrter Kunde,

    vielen Dank fr das Vertrauen, das Sie Testo mit dem Kauf die-ses Megertes entgegengebracht haben. Sie haben eine guteWahl getroffen. Sollten Sie trotzdem Grund zur Beanstandungunseres Produktes haben, beheben wir Mngel kostenlos, dienachweislich auf einen Werksfehler beruhen. Voraussetzung ist,da Sie diesen Mangel unverzglich nach Feststellung undinnerhalb der von uns gewhrten Garantiezeit melden.

    Natrlich sind Verschleiteile wie zum Beispiel Akkus, Mezel-len, Filter, Meelemente usw. sowie leicht zerbrechliche Teilevon dieser Garantie ausgenommen. Ebenso Schden, diedurch nicht bestimmungsgemen Gebrauch sowie infolge vonNichtbeachtung der Bedienungsanleitung entstanden sind.

    Die Garantie entfllt auerdem, wenn das Megert geffnetwurde - soweit dies nicht ausdrcklich in der Bedienungsanlei-tung zu Wartungszwecken beschrieben ist - oder aber Serien-nummern im Gert verndert, beschdigt oder entfernt wurden.

    Die Garantiezeit betrgt fr Handgerte 24 Monate, fr Fhler12 Monate. Wenn nicht anders definiert, gelten fr Zubehrteile6 Monate. Garantieleistungen bewirken keine Verlngerung derGarantiefrist.

    Wurden neben der Garantieleistung notwendige Reparaturen,Justagen oder dergleichen durchgefhrt, sind die Garantie-leistungen kostenlos, die anderen Leistungen werden aberebenso wie Transport und Verpackung berechnet.

    Weitergehende oder andere Ansprche, insbesondere bei ent-standenen Schden die nicht das Gert betreffen, sind - soweiteine Haftung nicht zwingend gesetzlich vorgeschrieben ist -ausgeschlossen.

    Leistungen nach der Garantiezeit

    Selbstverstndlich sind wir auch nach Ablauf der Garantiezeitfr Sie da. Bei Funktionsstrungen senden Sie uns Ihr Me-gert mit einer kurzen Fehlerbeschreibung. Geben Sie bitteauch Ihre Telefonnummer fr eventuelle Rckfragen an.

    Bei uns wird KUNDENDIENST gro geschrieben.

    Garantie

  • Instruction manual

    Flue Gas Analyser

    testo 325-I

    SO2

    NO

    COlow

    COhigh

  • Operation via power unit Only use the original power unit for operating the instrument.

    IntegrityBefore each measurement the complete measuring system(probe, condensate trap, hoses and plug connections) must bechecked for integrity, e.g. by attaching a compressed rubberbladder to the tip of the probe. If secondary air is drawn in,measuring errors may result.

    Gas outputDuring measurement, ensure that the gas output of theanalyser is open, so that the gas can escape unimpeded. Ifthis is not the case, falsification of the measuring results mayoccur.

    Condensate trapEmpty the condensate trap when the maximum mark isreached, at the latest. The pump must be switched off(otherwise the measuring cells are at risk)!Measuring cells The measuring cells contain a small quantity of concentratedacid or lye, and should be disposed of as special waste.

    Measuring instrumentKeeping the measuring instruments in rooms in which solventsare stored will result in damage to the measuring cells.

    Warning notes

    Initial operation

    3Measuring instrument conform with EN 61 326-1 Class B: 1997, EN 61 326-1: 1997

    Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Initial operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

    Warning notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Gas path . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Instrument diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

    Measurement example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Flue gas measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Printout of measured results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Setting the date/time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

    Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Changing rechargeable battery or battery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Condensate trap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Changing the filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Cleaning the flue gas pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Changing the measuring cells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

    Error messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

    Testo printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

    Cross sensitivities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Warranty conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Ordering data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Testo worldwide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

    Dear Testo Customer,

    You have made the right decision in purchasing the testo 325-1. Every year thousands ofcustomers purchase our high quality products. There are at least 7 good reasons for this:

    1) We have achieved the right price/performance ratio. Reliable quality at a fair price.2) Considerably extended warranty periods of up to 3 years -depending on the instrument!3) With specialist experience of over 40 years, we can provide the optimum solution for your

    measuring task.4) Our high quality standards are confirmed by certification in accordance with ISO 9001.5) Naturally our instruments bear the CE mark required by the EU .6) Calibration certificates for all relevant measurement quantities. Seminars, consultation and

    calibration on site.7) And even after purchase, we wont leave you in the lurch.

    Our service guarantees rapid assistance.

    Contents

    Introduction

    2

  • Initial operation

    5

    Instrument diagram

    Gas input

    Power unitconnection

    Time

    PrinterBattery capacity

    Zeroing phase

    Pump/Measurementon/off

    Print buttonThe measured valueshown in the displayis printed.

    Cancel/Back

    OK buttonThe menu for settingthe date and time isactivated.

    Date

    Measurement unit

    Pump active

    On/off button

    Scroll buttons / selection button

    With the right arrow buttonyou can access the variableparameters in the date/timemenu. Set the parameters withthe up/down buttons.

    Measured value

    Measured value designation

    Conden-sate trap

    FilterOutletopening

    Initial operation

    4

    Gas path

    Power supply

    Standard rechargeable batteries or batteries- Use standard rechargeable battery type (1.5V IEC KR 15/51

    in accordance with type AA) or battery type (1.5V round cell,

    Testo power unit (0554.0054)- Ensure good contact of the connection plug in the testo 325-I.- Operation possible via power unit even with empty

    rechargeable batteries/batteries.(Accumulators cannot be charged in the device)

    Capacity display

    Voltage >4.6 V (service life approx. 3 h, at anambient temperature of 20C)

    flashing symbol, voltage

  • 7The measured value is printed out with

    - Date/time- Unit of measurement

    (For date/time setting, see reference unit)

    From the measuring menu, printout of the measured values canbe triggered with the Print button. Printout is only possiblewhen the pump is stationary. Cancel the printing procedure withthe ESC button.

    testo 325-I07.09.1999 10:19:35

    SO2 1225 ppm

    Date/time

    Measured value

    Measurement example

    Printout of measured results

    STARTSTOP

    Measuring menu

    ppm225

    SO2

    Measuring menu

    ppm225

    SO2

    Measuring menu

    ppm225

    SO2

    Activate the set-point with the OK button.Change the setting field with the right button.Increase the value with the up button, decrease the value withthe down button.

    The OK button confirms the settings and takes you to themeasuring menu.The ESC button takes you back to the main menu, withoutadopting the settings.

    15.031999

    03.151999

    14:15Setting fieldflashesChangeover to

    US format

    TimesymbolDate

    symbol

    Setting the date/time

    OK

    OK

    DDAATT DAT

    6

    Measurement example

    Flue gas measurementExample: testo 325-I SO2

    3 sec. 3 sec. 60 sec.V 110

    6.0 43

    STARTSTOP

    ppm0

    SO2

    Flush the measuring cells with fresh air after eachmeasurement (pump start/stop) until the CO/NO/SO2content is below 50 ppm.

    Ensure that gas paths are dry when measuring SO2.

    Connectprobe

    Self-test Measuring menu

    Measuring menu

    Printout

    Pumprunning.

    Battery capacity Zeroing phase

    Switch ontesto 325-I

    ppm225

    SO2

    CAL.

    STARTSTOP

  • 9MaintenanceCleaning the flue gas pump

    Open the housing of the measuring instrument (see page 10,points 1-8).- Carefully remove the pump.- Place the pump tool into the guides of the pump head.- Remove the pump tool with the pump head.- Remove the diaphragm holder from the pump head and

    remove the diaphragm.- Clean pump diaphragm, pump plate and pump head with

    spirit or water.- Insert pump diaphragm into the diaphragm mounting and

    introduce into the pump head.- Attach pump head to the pump.- Remove pump tool.- Fit pump into the mounting block.- Assemble measuring instrument (see page 11).

    PUMP

    TOOL

    Pump(Part no.0239.0015)

    Pump plate

    Pump head

    Pump tool

    Pump tool(Part no.0192.0468)

    Diaphragm(Part no.0193.0072)

    Diaphragmholder

    Condensate trap

    Changing the filter

    In the event of visually detectable contamination of the filter, thefilter must be replaced.

    To do this, unlock the condensate trap and remove from thehousing.

    Remove the filter and replace with a new one. Order areplacement filter (Part no. 0554.0040, pack of 10).Only use this filter.

    Perform an integrity check after each filter change (seepage 3).

    Do not exceed level indicator of condensate trap.

    To empty the condensate trap, remove the drain plug.

    Remove dead/defective rechargeable batteries or deadbatteries from the battery compartment and replace with newrechargeable batteries or batteries.

    Caution!Observe correct polarity of rechargeable batteries or

    batteries!

    Switch off the instrument before changing therechargeable battery or battery.

    Perform change within 1 - 2 minutes or insert powerunit.

    Otherwise there is a risk of losing the set date/timevalues.

    Before changing the filterempty the condensate trap.

    8

    Maintenance

    Changing rechargeable battery or battery

    Filter

    Levelindicator

    Condensatedrain

    12

    3

    4

    m a x

    ma

    x

  • 11

    Changing the COlow measuring cell

    Before fitting the new COlow measuring cell, carefullyremove the short-circuit springs from the contacts.

    - Remove measuring cell from the measuring chamber coverand attach new measuring cell.

    Short-circuitspring

    COlow measuring cell

    Changing the SO2, NO, COhigh measuring cell

    - The measuring cell is located in the measuring chamber.Remove measuring cell and insert new measuring cell. Whenfitting, observe the guides on the measuring cell and themeasuring chamber.

    - Before fitting the new SO2,NO/COhigh cells, remove theshort-circuit springs carefully from the contacts.

    Assembling the testo 325-I

    - Place measuring chamber cover on the measuring chamber.Tighten the fastening screws (3 pieces).

    - Connect mounting block to the electronics.- Place mounting block and electronics in the top section of the

    housing.- Fix the mounting block and the electronics to the top section

    of the housing with the mounting screws (2 pieces).- Attach bottom section of housing and close in the opposite

    direction to the arrow.Note: Do not let keypad ribbon cable get caught.

    - Fit fixing plate and insert filter.- Attach condensate trap. Listen for the engagement tone.- Insert batteries/rechargeable batteries and close with battery

    compartment cover.

    - Remove NO filter from the measuring chamber. Wheninserting the new filter, ensure that the surface with theboreholes is positioned downwards in the measuringchamber.

    Maintenance

    Changing the COlow measuring cell

    When a COlow-measuring cell is changed, the NO-filtermust also be replaced.

    10

    Before touching the electronics, discharge any staticelectricity from your own body.

    Avoid touching the electronics.

    Battery compartmentcover

    Condensate trap

    Fixing plate

    Measuringchamber

    CO lowmeasuring cell

    Fastening screws

    NO filter

    Filter

    Mounting blockSO2, NO,CO highmeasuring cell

    Measuring chambercover

    Board

    Mounting screws

    1.) Remove hose connectors from the flue gas probe, as wellas the power unit of the testo 325-I .

    2.) Empty condensate trap before removing.3.) Unlock condensate trap and remove from the housing.4.) Remove filter insert (see page 8).5.) Remove fixing plate with a screwdriver.6.) Open battery compartment and remove

    batteries/rechargeable batteries (see page 8).7.) The housing of the testo 325-I is opened by

    moving the housing sections in the direction of the arrow (see diagram).

    8.) Remove bottom section of housing.9.) Loosen mounting screws (see diagram).

    10.) Remove mounting block with the electronicsfrom the top section of the housing (see below).

    11.) Remove mounting block from the board.12.) Loosen fastening screws (3 pieces) of the

    measuring chamber cover. Remove cover.

    Fixing plate

    Bottom of housing

    Top of housing

    Mounting screws

    Maintenance

    Changing the measuring cells

  • 13

    Error messageError messages during the measuring operation

    flashes

    During the zeroing phaseSO2 D flashes NO D flashesCOlow D flashesCOhigh D flashes

    Before switching offSO2 flashesNO flashesCOlow flashesCOhigh flashes

    After switching on/zeroing phaseSO2 A flashesNO A flashesCOlow A flashesCOhigh A flashes

    Error messages

    Cause / Remedy

    Permissible operating temperature exceeded.The ambient temperature changes to non-permissible values. Adjust ambient temperature.

    Measurement of zeroing point not stable. Waituntil zeroing phase has been repeated.If this is not successful, the measuring cell isused up.

    There is still flue gas in the instrument, or veryhigh concentrations were measured during thelast measurement, or the zeroing phase isprolonged.Cause: Insufficient flushing with fresh air afterlast measurement or probe is located in the fluegas. Place probe in fresh air. If no change occurs

    after repeated cycling of the zeroing phase,there is a fault in the cell or the cell is used up.

    Instrument distribution voltage becoming too low.Charge rechargeable battery/change battery orconnect power unit.

    There is still flue gas in the instrument, or veryhigh concentrations were measured during thelast measurement or the zeroing phase isprolonged.Cause: Insufficient flushing with fresh air afterlast measurement or probe is located in the fluegas. Place probe in fresh air. If no change occurs

    after repeated cycling of the zeroing phase,there is a fault in the cell or the cell is used up.

    LOW BAT

    12

    Input of SO2, NO, CO cell coefficient

    The cell coefficient is located on the instruction leaflet of thecorresponding replacement measuring cell.

    After entering the coefficients and confirming with the OK button, you jump to the zeroing phase.During the calibration phase you can jump to the zeroing phaseat any time by pressing the ESC button twice.

    Keep the Print button and the Right button pressed downsimultaneously for 3 seconds during the capacity display.

    Recalibration can be performed by Testoservice points, subsidiary companies andagents.

    SO2

    C

    25.5025.8

    Selectdecimalpoints

    Increase numeric value

    Decrease numeric value

    3 sec.

  • 15

    testo 325-I

    General technical data

    Max. low pressure in flue gas: 50 hPaWeight: 500gDimensions: 216 x 68 x 47 mmTransport/storage temperature: 20 to +50 CAmbient temp.: +4 to +45 CPower supply: via power unit, batteries or

    replaceable rechargeable batteriesBattery service life: > 4 hHousing material: ABS

    Flue gas probe

    Sampling pipe: Length 300 mm, 6 mmOperating temperature: Max. + 500 CHose length: 3 m (Tygon material in

    SO2 version)

    Technical data

    testo 325-I testo 325-I testo 325-I testo 325-ISO2 NO CO low CO high

    Meas. range 0 to 3000 ppm 0 to 1000 ppm 0 to 2000 ppm 20 to 40,000 ppm

    Accuracy up to 400 ppm up to 400 ppm up to 400 ppm up to 800 ppm< 20 ppm < 20 ppm < 20 ppm < 40 ppm

    up to 2000 ppm 5% of m.v.

    > 400 ppm > 200 ppm > 400 ppm >2000 ppm< 5% of m.v. < 5% of m.v. < 5% of m.v. < 10% of m.v.

    Setting time t90 < 80 s < 60 s < 60 s < 70 s

    Resolution 1 ppm 1 ppm 1 ppm 5 ppmfrom 10.000 ppm

    0.001 Vol. %

    14

    Technical dataType of printer: . . . . .Infrared-controlled thermal printerOperating temperature: . . . . . . . . . . . . . . . .0 to +50 CStorage/transport temp.: . . . . . . . . . . . . .-40 to +60 CDimensions: . . . . . . . . . . . . . . . . . . .150 x 88 x 50 mmWeight: . . . . . . . . . . . . . . . . . . .0.33 kg (incl. batteries)Power supply: . . . . . . . . . . . . . . . . . .4 1.5V round cells

    or NC rechargeable batteriesAccessories: .Replacement paper Part no. 0554.0569

    - Paper feed- Return from rest mode- Self-test = Keep button

    pressed down whenswitching on.

    Transmission distance:

    Magnetic plate onthe back of the

    device

    Caution: After approx. 10 minutes of inactivity theprinter switches into rest mode.

    Disposal note:Throw discharged batteries into collectionbox. In order to prevent short circuits, putthe batteries in individual plastic bags.

    6060

    max. 2 m

    10

    20

    Adjustcontrast

    ON/OFF

    Printabl

    e page

    Data receipt and operatingcontrol lamp

    green = ON/Battery o.k.yellow = ON/Battery warningred = ON/Battery dead

    Do not mark the window!

    I0

    Testo printer 0554.0545

    Accessories

    Cross-sensitivitiesCross gas

    Module CO NO SO2 NO2 H2S H2 CI2 HCI HCN CO2CO(H2) --- 0 0 0 0 0 0 0 0 0NO 0 --- 0

  • 17

    testo 325-I

    Ordering data

    Description Part no.

    Device

    Flue gas analyser testo 325-I (SO2) incl. batteries 0632.3260Flue gas analyser testo 325-I (NO) incl. batteries 0632.3261Flue gas analyser testo 325-I (COlow) incl. batteries 0632.3262Flue gas analyser testo 325-I (COhigh) incl. batteries 0632.3263

    Flue gas probes

    Flue gas probe (length 300 mm, Tmax +500 C, SO2) 0600.7541Flue gas probe (length 300 mm, Tmax +500 C) 0600.7542Cone for flue gas probe 0554.9050Flue gas probe (length 700 mm, Tmax +1000 C) incl. special hose

    for SO2 measurements 0699.3451/3

    Printer

    Testo printer 0554.0545

    Accessories

    Instrument SoftCase (for fixing to the boiler) 0516.2570Instrument box (plastic type) 0516.3250Power unit (230 V for mains operation) 0554.1084GB power unit 0554.0041J power unit 0554.0052USA power unit 0554.0053Replacement particle filter for testo 325-I (10 off) 0554.0040Replacement paper for printer 0554.0569

    Replacement cells

    COlow replacement cell incl. filter 0390.0168COhigh replacement cell 0390.0142SO2 replacement cell 0390.0143NO replacement cell 0390.0144

    16

    Warranty terms

    Instrument: 2 years Sampling probe : 1 yearAccessories 6 monthsMeasuring cells 6 monthsPrinter 1 year (except printing

    mechanism)

    Dear Customer,

    Thank you for the trust that you have shown Testo bypurchasing this analyser.You have made a good choice.However, should you have cause to complain about ourproduct, we will remedy, free of charge, any defects that can beproved to be caused by a factory error. The prerequisite is thatyou report this defect as soon as it is detected and within thewarranty period granted by us.

    Wearing parts, such as, for example, rechargeable batteries,measuring cells, filters, measuring elements, etc., as well asvery fragile parts are naturally excluded from this warranty. Thisalso applies for damages which have occurred due to improperuse or as a result of non-observance of the instruction manual.

    The warranty is also invalid if the analyser has been opened -provided this is not expressly described for maintenancepurposes in the instruction manual - or if serial numbers in thedevice have been changed, damaged or removed.

    The warranty period for hand-held instruments is 2 years, forprobes 1 year. If not otherwise defined, 6 months is the applica-ble period for accessory parts. Actions carried out underwarranty do not result in an extension of the warranty period.

    If in addition to the warranty actions necessary repairs,adjustments or similar have been performed, the warrantyactions are free of charge, but the other actions, as well astransport and packaging, are charged.

    More extensive or other claims are excluded, particularly in thecase of damages arising which do not concern the device, pro-vided that liability is not compulsorily stipulated by law.

    Service after the warranty period

    Naturally, we are here for you even when the warranty periodhas expired. In the event of malfunctions, send us your measur-ing instrument with a brief description of the fault. Please alsostate your telephone number in case we have any queries.

    With us CUSTOMER SERVICE is written in capital letters.

    Warranty

  • Testo weltweit

    Testo worldwideTesto worldwide

    Testo weltweit

    ARGENTINATesto Argentina S.A.C1440ACR - Buenos AiresTel. (11) 46 83 - 50 50Fax (11) 46 83 - 50 [email protected]

    ASIATesto (Asia) Ltd.Shatin, N. T., Hong KongTel. (2) 26 36 38 00Fax (2) 26 47 23 [email protected]

    AUSTRALIATesto Pty. Ltd.Bayswater, Victoria 3153Tel. (3) 97 20 00 11Fax (3) 97 20 00 [email protected]

    AUSTRIATesto Ges. mbH1170 WienTel. (1) 4 86 26 11- 0Fax (1) 4 86 26 11 [email protected]

    BELGIUM / LUXEMBURGS. A. Testo N. V.1741 TernatTel. (2) 5 82 03 61Fax (2) 5 82 62 [email protected]

    BOLIVIAT.E.C.CochabambaTel. (4) 4 40 09 17Fax (4) 4 28 60 [email protected]

    BOSNIA-HERZIGOWINATehnounion SarajevoSarajevoTel. (33) 20 59 44Fax (33) 44 40 00BRAZILTesto do Brazil13028-015 Campinas - SPTel. (19) 37 31 - 58 00Fax (19) 37 31 - 58 [email protected]

    BULGARIAGlobal Test OOD1408 SofiaTel. (2) 9 53 07 96,Fax (2) 9 52 51 [email protected]

    CHILEANWO S.A.SantiagoTel. (2) 7 31 00 00Fax (2) 2 73 04 [email protected]

    CHINATesto (Far East) Ltd.Shanghai 200031Tel. (21) 54 56 - 64 70Fax (21) 54 56 - 14 [email protected]

    CISGlobal Export GmbH105 023 MoscowTel. (0 95) 3 60 53 68Fax (0 95) 3 60 53 [email protected]

    COLOMBIAArotec Colombiana S. A.Bogota D. E.Tel. (1) 2 88 77 99Fax (1) 2 85 36 [email protected]

    COSTA RICARepresentacionesCorelsa S. A.Santo Domingo de HerediaTel. 2 44 25 50Fax 2 44 30 [email protected]

    CROATIA"H.I.P." Zagreb d.o.o.10090 ZagrebTel. (1) 3 73 40 07Fax (1) 3 73 40 [email protected]

    CYPRUSDeksa Ltd.NicosiaTel. (2) 2 45 55 55Fax (2) 49 70 [email protected]

    CZECH REPUBLICTesto s.r.o.158 00 Praha 5Tel. (2) 57 29 02 05Fax (2) 57 29 04 [email protected]

    DENMARKBuhl & Bonsoe A/S2830 VirumTel. 45 95 04 10Fax 45 95 04 [email protected]

    EASTERN EUROPETesto Osteuropa GmbH79850 LenzkirchTel. (0 76 53) 6 81 - 141Fax. (0 76 53) 6 81 - [email protected]

    EGYPTFuture Plants ContractorsHeliopolis 11361, CairoTel. (2) 4 18 67 79Fax (2) 4 18 95 [email protected]

    EL SALVADOREco Control S.A de C.V.San SalvadorTel. 2 60 66 01Fax 2 60 66 [email protected]

    FINLANDHumitec Oy00410 HelsinkiTel. (9) 5 30 84 00Fax (9) 53 08 40 [email protected]

    FRANCEtesto Srl57602 ForbachTel. 3 87 29 29 00Fax 3 87 87 40 [email protected]

    GREECESigma Hellas Ltd.18536 PiraeusTel. (10) 4 18 01 67Fax (10) 4 51 90 [email protected]

    GREAT BRITAINTesto Ltd.Alton, Hampshire GU34 2QJTel. (14 20) 54 44 33Fax (14 20) 54 44 [email protected]

    HONG KONGTesto Far East Ltd.Shatin, N. T., Hong KongTel. (2) 26 36 38 00Fax (2) 26 47 23 [email protected]

    HUNGARYTesto Kft.1139 BudapestTel. 237 17 47Fax 237 17 [email protected]

    ICELANDRafn Jensson, MechanicalEngineers ehf110 ReykjavikTel. 5 67 80 30Fax 5 67 80 [email protected] Instruments Co. (P) Ltd.Bangalore 560 054Tel. (80) 3 60 25 60Fax (80) 3 60 36 [email protected]

    IRANMehr Kanaz Sanat Co.TehranTel. (21) 2 26 26 89Fax (21) 2 22 37 [email protected]

    ISRAELManoraz Ltd.Azur 58001Tel. (3) 5 59 33 99Fax (3) 5 58 44 [email protected]

    ITALYTesto S.p.A.20019 Settimo Milanese (Mi)Tel. (02) 3 35 19 - 1Fax (02) 3 35 19 - [email protected]

    JAPANTesto K.K.Yokohama 222-0033Tel. (45) 4 76 22 88Fax (45) 4 76 22 [email protected] Technique Est.Sahab 115-12Tel. (6) 4 02 95 22Fax (6) 4 02 35 [email protected] (Republic of)Testo (Korea) Ltd.Seoul 150-102Tel. (2) 6 72 72 00Fax (2) 6 79 98 [email protected]

    MALTATechnoline Ltd.Gzira GZR 06Tel. (21) 34 23 66Fax (21) 34 39 [email protected]

    MACEDONIAPharmachem Skopje1060 SkopjeTel. (2) 33 11 93Fax (2) 33 14 [email protected]

    MAROCA.F.M.I.L. SARLBelevedere-CasablancaTel. (22) 24 01 84Fax (22) 24 01 [email protected]

    MEXICOGrupo de Instrumentacin yMedicin Industrial de Mxico,S.A. de C.V.08920 Mexico, D.F.Tel. (55) 56 34 04 02Fax (55) 56 33 04 [email protected]

    NETHERLANDSTesto B.V.1314 BH Almere-StadTel. (36) 5 48 70 00Fax (36) 5 48 70 [email protected]

    NEW ZEALANDEurotec Instruments Ltd.AucklandTel. (9) 5 79 19 90Fax (9) 5 25 33 [email protected]

    NICARAGUAAdolfo Grber & Ca Ltda.ManaguaTel. 2 66 51 36Fax 2 66 51 [email protected]

    NORWAYMax Sievert A/S0134 OsloTel. (22) 17 30 85Fax (22) 17 25 [email protected]

    PERUJJL Asociados S.A.Lima 17Tel. (1) 2 61 17 52Fax (1) 2 61 46 [email protected] IndustrialTrading CorporationPasay City 1300,Tel. (2) 8 31 95 71Fax (2) 8 31 40 [email protected]

    POLANDTesto Sp. z.o.o.02-362 WarszawaTel. (22) 8 63 74 22Fax (22) 8 63 74 [email protected]

    PORTUGALTesto Lda.3800-559 CaciaTel. 9 67 60 45 34Fax 2 34 08 37 [email protected]

    REP. OF SOUTH AFRICAUnitempLandsdowne, Cape Town, 7779Tel. (21) 7 62 89 95Fax (21) 7 62 89 [email protected]

    ROMANIATest Line SRL72217 BucharestTel. (21) 6 87 34 62Fax (21) 2 42 68 [email protected]

    SINGAPORE / MALAYSIA /INDONESIAFutron Electronics PTE LTDSingapore 329 714Tel. (65) 62 50 24 56Fax (65) 62 50 65 [email protected]

    SLOVAKIAK - Test s.r.o.042 60 KosiceTel. (1) 55 625 36 33Fax (1) 55 625 36 [email protected]

    SLOVENIATehnounion D.D.1000 LjubljanaTel. (1) 5 13 50 88Fax (1) 5 13 52 [email protected] Testo S. A.08348 CabrilsTel. (93) 753 95 20Fax (93) 753 95 [email protected]

    SWEDENNordtec Instrument40241 GteborgTel. (31) 704 10 70Fax (31) 12 50 [email protected]

    SWITZERLANDTesto AG8604 VolketswilTel. (1) 9 08 40 50Fax (1) 9 08 40 [email protected]

    SYRIAMedical Business CenterDamascusTel. (11) 2 32 23 01Fax (11) 2 31 75 [email protected]

    TAIWAN, R.O.C.Hot Instruments Co. Ltd.Chungho CityTel. (2) 89 23 23 18Fax (2) 89 23 23 [email protected]

    THAILANDEntech Associate Co. Ltd.Bangkok 10210Tel. (2) 9 54 54 99Fax (2) 9 54 54 [email protected]

    TUNISIAStareprImmeuble Mouradi (Touta)2000 Le BardoTel. (71) 50 92 86Fax (1) 58 49 [email protected]

    TURKEYTesto Elektronik ve Test lcmCihazlari Dis Ticaret Ltd. STi80280 Esentepe-IstanbulTel. (212) 2 75 77 99Fax (212) 2 72 06 [email protected]

    UNITED ARAB EMIATESEnviro engineeringGeneral TradingDubaiTel. (14) 2 27 70 20Fax (14) 2 23 36 [email protected]

    USATesto Inc.Flanders, NJ. 07836Tel. (973) 2 52 17 20Fax (973) 2 52 17 [email protected]

    VENEZUELAG & M International Service,C. A.San Antonio de los Altos,Edo.MirandaTel. (2) 3 72 77 70Fax (245) 5 71 67 [email protected]

    VIETNAMMTCMeasuring and TestingEquipment Company Ltd.HanoiTel. (4) 7 33 36 36Fax (4) 7 33 21 [email protected]

    _________________________

    Stand: 01.08.2002Stets aktualisierte Adressdatenunserer Tchter und Landes-Vertriebspartner finden Sie imInternet unter: www.testo.com

    01.08.2002The most up-to-date addressdetails of our subsidiaries andagencies can be found in Internetat: www.testo.com

  • Head office / HauptsitzTesto AG Postfach 11 40, D-79849 Lenzkirch Testo-Strae 1, D-79853 LenzkirchTel. (0 76 53) 6 81 - 0 Fax (0 76 53) 6 81 - 1 00E-Mail: [email protected]://www.testo.de

    Kundendienst / Service departmentTesto AGKolumban-Kayser-Str. 17, D-79853 LenzkirchSoftware-Hotline (0 76 53) 6 81 - 630 E-Mail: [email protected] (0 76 53) 6 81 - 620E-Mail: [email protected] (0 76 53) 6 81 - 610E-Mail: [email protected]. Bearbeitung (0 76 53) 6 81 - 600E-Mail: [email protected] (0 76 53) 6 81 - 601http://www.testo.de

    Kundencenter / Service centerNord22457 HamburgTel. (0 40) 55 97 23 - 0Fax (0 40) 55 97 23 - 50Auenstelle BremenTel. (04 21) 54 28 15Fax (04 21) 54 59 37Auenstelle HannoverTel. (0 53 44) 26 15 - 28Fax (0 53 44) 26 15 - 29West42555 Velbert-LangenbergTel. (0 20 52) 95 37 - 0Fax (0 20 52) 95 37 37Auenstelle Groraum KlnTel. (0 65 56) 9 30 53Fax (0 65 56) 9 30 54Mitte65520 Bad CambergTel. (0 64 34) 91 55 - 0Fax (0 64 34) 91 55 - 70Auenstelle Mannheim / HeidelbergTel. (0 63 21) 60 00 28Fax (0 63 21) 60 00 29

    Sdwest72770 ReutlingenTel. (0 71 21) 5 15 38 - 0Fax (0 71 21) 5 15 38 - 20Sdost90455 NrnbergTel. (09 11) 46 25 88 30Fax (09 11) 46 25 88 40Auenstelle RegensburgTel. (0 94 03) 96 18 10Fax (0 94 03) 96 18 11 Auenstelle MnchenTel. (0 89) 4 70 95 94Fax (0 89) 4 70 95 92Nordost13409 BerlinTel. (0 30) 4 96 40 46Fax (0 30) 4 96 50 44Auenstelle GroheringenTel. (03 64 61) 2 07 93Fax (03 64 61) 2 07 99

    0973.3253/T/wh/PC_qxd/08.02