Zf Fault Codes Latest

ZF FRIEDRICHSHAFEN Aktiengesellschaft

Benennung: Zusatzbenennung:

fault codes description of fault codes for Ergo control

Nr.:

DIN A4

Seite 1 von 38

Diese technische Unterlage darf weder kopiert noch dritten Personen ohne unsere Erlaubnis

34

09-10-22 Schwarz

mitgeteilt werden. Index Nr. Datum Name Film K3 ZFN 904 N D E R U N G E N

Erstellt: Geprft: Freigegeben : Name: Plank Sieger Abteilung: ACETS TE-AB Datum: 2011-02-21 03-10-01

Description of the

fault codes for

ERGO-Control EST37

document created for customer "Hyundai construction machineries" 2011-02-21

ZF Friedrichshafen AG 11-02-21 Faultcodes ERGO-Control EST37A

TE-AB Seite 2 von 38

Index of changes:

date index comment software version



1 Introduction

1.1 Abbreviations

o.c. open circuit s.c. short circuit OP-Mode operating mode TCU transmission control unit EEC electronic engine controller PTO power take off

1.2 ZF - Display: If a fault is detected, the display shows a spanner symbol (g) for a fault. The display shows the fault code, if the gear selector is on neutral position. If more than one fault is detected, each fault code is shown for about 1 second.

STOP

h f e d

a b c g

(special symbols a-h)

leftcharacter

rightcharacter

1.3 Display during operation Symbol meaning remarks 1F, 1R 2F, 2R 3F, 3R 4F 5F 6F LF, LR

actual gear and direction left digit shows actual gear right digit shows actual direction

limp home gear

F or R, no gear Clutch Cutoff F or R flashing direction F or R selected while turbine

speed is too high CAUTION gear will engage if turbine speed drops

NN not neutral, waiting for neutral after power up or a severe fault

to engage a gear, first move shift selector to neutral position and again to F or R position

** oil temperature too low, no gear available

warm up engine / transmission

*N oil temperature low, only one gear available

warm up engine / transmission

1 bar (special manual mode 1st gear



symbol) 2 bars manual mode 2nd gear 3 bars manual mode 3rd gear 4 bars manual mode 4th gear and also 5th and

6th gear in 6WG

4 bars and 2 arrows

automatic mode

Bars flashing 6 WG: converter lockup clutch open

4 WG: Downshift mode activ

difference of engine and turbine speed above a certain limit and lockup clutch not activated

Spanner at least one fault activ select neutral to get fault code displayed Fault code see faultcode list WS warning sump temperature changes between actual gear/direction while driving,

in neutral only displayed if no fault is detected (spanner)

WR warning retarder temperature changes between actual gear/direction while driving, in neutral only displayed if no fault is detected (spanner)

WT warning torque converter temperature changes between actual gear/direction while driving, in neutral only displayed if no fault is detected (spanner)

WE warning high engine speed changes between actual gear/direction while driving, in neutral only displayed if no fault is detected (spanner)

WV warning high output speed (velocity) changes between actual gear/direction while driving, in neutral only displayed if no fault is detected (spanner)

WL warning high transmission input torque (load)

changes between actual gear/direction while driving, in neutral only displayed if no fault is detected (spanner)

WO warning high transmission output torque (load)

changes between actual gear/direction while driving, in neutral only displayed if no fault is detected (spanner)

PN direction F or R selected while parking brake engaged

transmission in neutral until parking brake is released CAUTION: vehicle starts to move after release of parking brake

EE flashing no communication with display checked wiring from TCU to display



1.4 Display during AEB-Mode symbol meaning remarks PL AEB - Starter is plugged at the

diagnostic plug

ST AEB-Starter-button is pressed K1..K4,KV,KR, KW

calibrating clutch K1..K4, KV or KR, KW is lockup clutch

_ and Kx wait for start, initialization of clutch Kx, x: 1, 2, 3, 4, V, R, W

and Kx fast fill time determination of clutch Kx = and Kx compensating pressure determination of

clutch Kx

OK calibration for all clutches finished Transmissions stays in neutral, you have to restart the TCU (ignition off/on) after removing AEB-Starter

STOP AEB canceled (activation stopped) Transmissions stays in neutral, you have to restart the TCU (ignition off/on)

STOP and Kx AEB stopped, clutch Kx can't be calibrated

Transmissions stays in neutral, you have to restart the TCU (ignition off/on)

Spanner and Kx Kx couldn't be calibrated, AEB finished Transmissions stays in neutral, you have to restart the TCU (ignition off/on)

E engine speed too low, raise engine speed

E engine speed too high, lower engine speed

T transmission oil temperature too low, heat up transmission

T transmission oil temperature too high cool down transmission

FT transmission temperature not in defined range during calibration


FB operating mode not NORMAL or transmission temperature sensor defective or storing of Calibrated values to EEPROM-has failed.


FO Outputspeed_not_zero Transmissions stays in neutral, you have to restart the TCU (ignition off/on)

FN Shift lever not in Neutral position Transmissions stays in neutral, you have to restart the TCU (ignition off/on)

FP Parkbrake_not_applied Transmissions stays in neutral, you have to restart the TCU (ignition off/on)

STOP AEB - Starter was used incorrect or is defective. Wrong device or wrong cable used




1.5 Display during Inchpedal Calibration symbol meaning remarks

IP push down the pedal slowly until endposition is reached and hold this position

IP Release the pedal slowly until endposition is reached

IP flashing A problem occurred, release the pedal slowly until endposition is reached

If the expected enposition could not be reached, release the pedal and try again

OK Finished inchpedal calibration successful

FN and Stop Shift lever not in Neutral position Calibration is aborted FS and Stop sensor supply voltage AU1 is out of

the specified range Calibration is aborted

FO and Stop Outputspeed is not zero Calibration is aborted SL and Stop sensor voltage below specified

rangel Calibration is aborted

SU and Stop sensor voltage above specified rangel

Calibration is aborted

IL and Stop sensor position for released pedal out of specified range


IU and Stop sensor position for pressed pedal out of specified range


TO and Stop time-out calibration, pedal not moved after calibration start


DL and Stop angle between pedalpositions released and pressed to small


DU and Stop angle between pedalpositions released and pressed to big


FI and Stop sensor signal 1 and 2 don't match together




2 definition of operating modes NORMAL:

There's no failure detected in the transmission-system or the failure has no or slight effects on

transmission control. TCU will work without or in special cases with little limitations. (see following table)

SUBSTITUTE CLUTCH CONTROL: TCU can't change the gears or the direction under the control of the normal clutch modulation. TCU

uses the substitute strategy for clutch control. All modulations are only time controlled. (Comparable with EST 25)

LIMP-HOME: The detected failure in the system has strong limitations to transmission control. TCU can engage

only one gear in each direction. In some cases only one direction will be possible.

TCU will shift the transmission into neutral at the first occurrence of the failure. First, the operator

must shift the gear selector into neutral position.

If output speed is less than a threshold for neutral to gear and the operator shifts the gear selector

into forward or reverse, the TCU will select the limp-home gear .

If output speed is less than a threshold for reversal speed and TCU has changed into the limp-home

gear and the operator selects a shuttle shift, TCU will shift immediately into the limp-home gear of

the selected direction.

If output speed is greater than the threshold, TCU will shift the transmission into neutral. The

operator has to slow down the vehicle and must shift the gear selector into neutral position.

TRANSMISSION-SHUTDOWN: TCU has detected a severe failure that disables control of the transmission.

TCU will shut off the solenoid valves for the clutches and also the common power supply (VPS1). Transmission shifts to Neutral. The park brake will operate normally, also the other functions which

use ADM 1 to ADM 8.

The operator has to slow down the vehicle. The transmission will stay in neutral.

TCU-SHUTDOWN: TCU has detected a severe failure that disables control of system.

TCU will shut off all solenoid valves and also both common power supplies (VPS1, VPS2). The park brake will engage, also all functions are disabled which use ADM 1 to ADM 8.

The transmission will stay in neutral.

ZF Friedrichshafen AG description of fault codes for ERGO-Control 11-02-21


3 table of fault codes

Fault Code (hex)

SPN FMI MEANING OF THE FAULT CODE possible reason for fault detection

reaction of the TCU possible steps to repair remarks

10 5001 12 LOGICAL ERROR AT DIRECTION SELECT SIGNAL 3RD SHIFT LEVER TCU detected a wrong signal combination for the direction cable from shift lever 3 to TCU is

broken cable is defective and is contacted to

battery voltage or vehicle ground shift lever is defective

TCU shifts transmission to neutral if selector activ OP-Mode: transmission shutdown if selector activ

check the cables from TCU to shift lever 3

check signal combinations of shift lever positions F-N-R

if shift lever is a CAN shift lever check CAN cable/shifter/device

fault is cleared if TCU detects a valid neutral signal for the direction at the shift lever

11 5000 12 LOGICAL ERROR AT GEAR RANGE SIGNAL TCU detected a wrong signal combination for the gear range cable from shift lever to TCU is broken cable is defective and is contacted to


TCU shifts transmission to neutral OP-Mode: transmission shutdown

check the cables from TCU to shift lever check signal combinations of shift lever

positions for gear range

fault is taken back if TCU detects a valid signal for the position

12 5010 12 LOGICAL ERROR AT DIRECTION SELECT SIGNAL TCU detected a wrong signal combination for the direction cable from shift lever to TCU is broken cable is defective and is contacted to


TCU shifts transmission to neutral OP-Mode: transmission shutdown

check the cables from TCU to shift lever check signal combinations of shift lever

positions F-N-R

fault is taken back if TCU detects a valid signal for the direction at the shift lever

13 5020 12 LOGICAL ERROR AT ENGINE DERATING DEVICE TCU detected no reaction of engine while derating device activ

after selecting neutral, TCU changes to OP-Mode limp home

check engine derating device This fault is reset after power up of TCU



Fault Code (hex)



14 5030 12 LOGICAL ERROR AT PARKBRAKE STATUS Parkbrake-status-signal measured by TCU and parkbrake-status-signal send by CAN don't fit one of the cables from status-switch to

electronic box is broken one of the status-switches is defective

TCU shifts transmission to DCO-State OP-Mode: normal

check the cables from electronic boxes to status switches

check signals of the status switches

15 5040 12 LOGICAL ERROR AT DIRECTION SELECT SIGNAL 2. SHIFT LEVER TCU detected a wrong signal combination for the direction cable from shift lever 2 to TCU is

broken cable is defective and is contacted to


TCU shifts transmission to neutral if selector activ OP-Mode: transmission shutdown if selector activ

check the cables from TCU to shift lever 2

check signal combinations of shift lever positions F-N-R

fault is taken back if TCU detects a valid neutral signal for the direction at the shift lever

16 5050 12 LOGICAL ERROR AT AXLE CONNECTION feedback axle connection measured by TCU and output signal axle connection don't fit axle cant be connected or

disconnected due to mechanical problem

one of the cables from feedback axle connection -switch to TCU is broken

OP-Mode: normal check the cables from TCU to feedback axle connection switch

check signals of the feedback axle connection switch

25 5110 3 S.C. TO BATTERY VOLTAGE OR O.C. AT TRANSMISSION SUMP TEMPERATURE SENSOR INPUT the measured voltage is too high: cable is defective and is contacted to

no reaction, TCU uses default temperature OP-Mode: normal

check the cable from TCU to the sensor check the connectors check the temperature sensor



Fault Code (hex)



battery voltage cable has no connection to TCU temperature sensor has an internal

defect connector pin is contacted to battery

voltage or is broken

26 5110 4 S.C. TO GROUND AT TRANSMISSION SUMP TEMPERATURE SENSOR INPUT the measured voltage is too low: cable is defective and is contacted to

vehicle ground temperature sensor has an internal

defect connector pin is contacted to vehicle

ground



27 5120 3 S.C. TO BATTERY VOLTAGE OR O.C. AT RETARDER / TORQUECONVERTER TEMPERATURE SENSOR INPUT the measured voltage is too high: cable is defective and is contacted to

battery voltage cable has no connection to TCU temperature sensor has an internal





28 5120 4 S.C. TO GROUND AT RETARDER / TORQUECONVERTER TEMPERATURE SENSOR INPUT the measured voltage is too low: cable is defective and is contacted to

vehicle ground





Fault Code (hex)



temperature sensor has an internal defect

connector pin is contacted to vehicle ground

29 5130 3 S.C. TO BATTERY VOLTAGE OR O.C. AT PARKING BRAKE SENSOR INPUT the measured voltage is too high: cable is defective and is contacted to

battery voltage cable has no connection to TCU sensor has an internal defect connector pin is contacted to battery


TCU uses default value OP-Mode: normal

check the cable from TCU to the sensor check the connectors check the parking brake sensor

2A 5130 4 S.C. TO GROUND PARKING BRAKE SENSOR INPUT the measured voltage is too low: cable is defective and is contacted to

vehicle ground sensor has an internal defect connector pin is contacted to vehicle

ground


check the cable from TCU to the sensor check the connectors check the parking brake sensor

2B 5313 12 INCHSENSOR-SIGNAL MISMATCH the measured voltage from CCO and CCO2 signal dont match: cable is defective sensor has an internal defect

During inching mode: TCU shifts to neutral While not inching: no change OP-Mode: normal

check the cable from TCU to the sensor check the connectors check sensor

2C 5135 3 S.C. TO BATTERY VOLTAGE OR O.C. AT DLM TRACTION ADJUST DASHBOARD DEVICE INPUT the measured voltage is too high:


check the cable from TCU to the sensor check the connectors check the DLM Traction Adjust

dashboard device



Fault Code (hex)



cable is defective and is contacted to battery voltage

cable has no connection to TCU sensor has an internal defect connector pin is contacted to battery


2D 5135 4 S.C. TO GROUND DLM TRACTION ADJUST DASHBOARD DEVICE INPUT the measured voltage is too low: cable is defective and is contacted to


ground


check the cable from TCU to the sensor check the connectors check the DLM Traction Adjust

dashboard device

2E 5137 3 S.C. TO BATTERY VOLTAGE OR O.C. AT DLM STEERING ANGLE SENSOR INPUT the measured voltage is too high: cable is defective and is contacted to

battery voltage cable has no connection to TCU sensor has an internal defect connector pin is contacted to battery



check the cable from TCU to the sensor check the connectors check the DLM STEERING ANGLE

SENSOR

2F 5137 4 S.C. TO GROUND DLM STEERING ANGLE SENSOR INPUT the measured voltage is too low: cable is defective and is contacted to


ground


check the cable from TCU to the sensor check the connectors check the DLM STEERING ANGLE

SENSOR



Fault Code (hex)



31 5140 3 S.C. TO BATTERY VOLTAGE OR O.C. AT ENGINE SPEED INPUT TCU measures a voltage higher than 7.00 V at speed input pin cable is defective and is contacted to

battery voltage cable has no connection to TCU speed sensor has an internal defect connector pin is contacted to battery

voltage or has no contact

OP-Mode: substitute clutch control

check the cable from TCU to the sensor check the connectors check the speed sensor

32 5140 4 S.C. TO GROUND AT ENGINE SPEED INPUT TCU measures a voltage less than 0.45V at speed input pin cable / connector is defective and is

contacted to vehicle ground speed sensor has an internal defect



33 5140 12 LOGICAL ERROR AT ENGINE SPEED INPUT TCU measures a engine speed over a threshold and the next moment the measured speed is zero cable / connector is defective and has

bad contact speed sensor has an internal defect sensor gap has the wrong size


check the cable from TCU to the sensor check the connectors check the speed sensor check the sensor gap

This fault is reset after power up of TCU

34 5150 3 S.C. TO BATTERY VOLTAGE OR O.C. AT TURBINE SPEED INPUT TCU measures a voltage higher than 7.00 V at speed input pin cable is defective and is contacted to

battery voltage cable has no connection to TCU speed sensor has an internal defect

OP-Mode: substitute clutch control if a failure is existing at output speed, TCU shifts to neutral OP-Mode: limp home




Fault Code (hex)



connector pin is contacted to battery voltage or has no contact

35 5150 4 S.C. TO GROUND AT TURBINE SPEED INPUT TCU measures a voltage less than 0.45V at speed input pin cable / connector is defective and is




36 5150 12 LOGICAL ERROR AT TURBINE SPEED INPUT TCU measures a turbine speed over a threshold and at the next moment the measured speed is zero cable / connector is defective and has





37 5160 3 S.C. TO BATTERY VOLTAGE OR O.C. AT INTERNAL SPEED INPUT TCU measures a voltage higher than 7.00 V at speed input pin cable is defective and is contacted to





38 5160 4 S.C. TO GROUND AT INTERNAL SPEED INPUT TCU measures a voltage less than 0.45V at speed input pin cable / connector is defective and is

contacted to vehicle ground





Fault Code (hex)



speed sensor has an internal defect

39 5160 12 LOGICAL ERROR AT INTERNAL SPEED INPUT TCU measures a internal speed over a threshold and at the next moment the measured speed is zero cable / connector is defective and has





3A 5170 3 S.C. TO BATTERY VOLTAGE OR O.C. AT OUTPUT SPEED INPUT TCU measures a voltage higher than 12.5 V at speed input pin cable is defective and is contacted to



special mode for gear selection OP-Mode: substitute clutch control if a failure is existing at turbine speed, TCU shifts to neutral OP-Mode: limp home


3B 5170 4 S.C. TO GROUND AT OUTPUT SPEED INPUT TCU measures a voltage less than 1.00V at speed input pin cable / connector is defective and is




3C 5170 12 LOGICAL ERROR AT OUTPUT SPEED INPUT TCU measures a output speed over a threshold and at the next moment the measured speed is zero cable / connector is defective and has

bad contact

special mode for gear selection OP-Mode: substitute clutch control if a failure is existing at turbine speed, TCU shifts to neutral





Fault Code (hex)



speed sensor has an internal defect sensor gap has the wrong size

OP-Mode: limp home

3E 5180 2 OUTPUT SPEED ZERO DOESNT FIT TO OTHER SPEED SIGNALS if transmission is not neutral and the shifting has finished, TCU measures outputspeed zero and turbine speed or internal speed not equal to zero. speed sensor has an internal defect sensor gap has the wrong size


check the sensor signal of output speed sensor

check the sensor gap of output speed sensor

check the cable from TCU to the sensor


54 5260 9 DCT1 TIMEOUT Timeout of CAN-message DCT1 from display computer interference on CAN-Bus CAN wire/connector is broken CAN wire/connector is defective and

has contact to vehicle ground or battery voltage

OP-Mode: normal check display computer check wire of CAN-Bus check cable to display computer

55 5270 9 JSS TIMEOUT Timeout of CAN-message JSS from Joystick Steering Controller interference on CAN-Bus CAN wire/connector is broken CAN wire/connector is defective and


TCU shifts to neutral while Joystick Steering is active OP-Mode: normal

check Joystick steering controller check wire of CAN-Bus check cable to Joystick steering

controller

56 5280 9 ENGINE CONF TIMEOUT Timeout of CAN-message ENGINE CONF from engine controller interference on CAN-Bus


check engine controller check wire of CAN-Bus check cable to engine controller



Fault Code (hex)



CAN wire/connector is broken CAN wire/connector is defective and


57 5290 9 EEC1 TIMEOUT Timeout of CAN-message EEC1 from EEC controller interference on CAN-Bus CAN wire/connector is broken CAN wire/connector is defective and



check EEC controller check wire of CAN-Bus check cable to EEC controller

58 5300 9 EEC3 TIMEOUT Timeout of CAN-message EEC3 from EEC controller interference on CAN-Bus CAN wire/connector is broken CAN wire/connector is defective an




59 5310 2 AEB-REQUEST AND PARKBRAKETEST SIGNALS ON AT THE SAME TIME CAN signal for AEB-Request and for ParkbrakeTest are ON at the same time

no reaction check programming of vehicle controller

61 5390 2 AEB REQUEST SIGNAL CAN signal for AEB request is defective I/O controller is defective interference on CAN-Bus

no reaction OP-Mode: normal Last selection is kept

check I/O controller check wire of CAN-Bus check cable to I/O controller

65 5430 2 ENGINGE TORQUE SIGNAL CAN signal for engine torque is defective engine controller is defective

OP-Mode:substitute clutch control




Fault Code (hex)



interference on CAN-Bus

69 5440 2 REFERENCE ENGINE TORQUE SIGNAL CAN signal for reference of engine torque is defective engine controller is defective interference on CAN-Bus



6A 5450 2 ACTUAL ENGINE TORQUE SIGNAL CAN signal for actual engine torque is defective engine controller is defective interference on CAN-Bus



6B 5460 2 NOM FRICTION TORQUE SIGNAL CAN signal for nominal friction torque is defective engine controller is defective interference on CAN-Bus



6E 5470 2 EEC2 TIMEOUT Timeout of CAN-message EEC2 from EEC controller interference on CAN-Bus CAN wire/connector is broken CAN wire/connector is defective and


no reaction, TCU uses default signal accelerator pedal in idle position OP-Mode: normal


71 5480 3 S.C. TO BATTERY VOLTAGE AT CLUTCH K1 the measured resistance value of the valve is out of limit, the voltage at K1 valve is too high. cable / connector is defective and has

contact to battery voltage

TCU shifts to neutral OP-Mode: limp home if failure at another clutch is pending TCU shifts to neutral OP-Mode: TCU shutdown

check the cable from TCU to the gearbox

check the connectors from TCU to the gearbox

check the regulator resistance 1) check internal wire harness of the

1) see chapter 4



Fault Code (hex)



regulator has an internal defect

gearbox

72 5480 4 S.C. TO GROUND AT CLUTCH K1 the measured resistance value of the valve is out of limit, the voltage at K1 valve is too low. cable / connector is defective and has

contact to vehicle ground cable / connector is defective and has

contact to another regulator output of the TCU




check the connectors from gearbox to TCU


gearbox

1) see chapter 4

73 5480 5 O.C. AT CLUTCH K1 the measured resistance value of the valve is out of limit. cable / connector is defective and has

no contact to TCU regulator has an internal defect





gearbox

1) see chapter 4


contact to battery voltage regulator has an internal defect





gearbox

1) see chapter 4







gearbox

1) see chapter 4



Fault Code (hex)











gearbox

1) see chapter 4







gearbox

1) see chapter 4









gearbox

1) see chapter 4


no contact to TCU

TCU shifts to neutral OP-Mode: limp home if failure at another clutch is pending TCU shifts to neutral



check the regulator resistance 1)

1) see chapter 4



Fault Code (hex)




OP-Mode: TCU shutdown check internal wire harness of the gearbox

7A 5540 3 S.C. TO BATTERY VOLTAGE AT CONVERTER CLUTCH

no reaction OP-Mode: normal

check the cable from TCU to the valve check the regulator resistance 1)

7B 5540 4 S.C. TO GROUND AT CONVERTER CLUTCH

CONVERTER LOCK UP CLUTCH SOLENOID CONNECTED AT ADMX: TCU switch off VPS2 OP-mode: normal

CONVERTER LOCK UP CLUTCH SOLENOID CONNECTED AT AIP7: TCU switch off VPS2 OP-mode: normal


7C 5540 5 O.C. AT CONVERTER CLUTCH









gearbox

1) see chapter 4









gearbox

1) see chapter 4



Fault Code (hex)









gearbox

1) see chapter 4

84 5520 3 S.C. TO BATTERY VOLTAGE AT CLUTCH KV the measured resistance value of the valve is out of limit, the voltage at KV valve is too high. cable / connector is defective and has






gearbox

1) see chapter 4

85 5520 4 S.C. TO GROUND AT CLUTCH KV the measured resistance value of the valve is out of limit, the voltage at KV valve is too low. cable / connector is defective and has








gearbox

1) see chapter 4

86 5520 5 O.C. AT CLUTCH KV the measured resistance value of the valve is out of limit. cable / connector is defective and has






gearbox

1) see chapter 4



Fault Code (hex)



87 5530 3 S.C. TO BATTERY VOLTAGE AT CLUTCH KR the measured resistance value of the valve is out of limit, the voltage at KR valve is too high. cable / connector is defective and has






gearbox

1) see chapter 4

88 5530 4 S.C. TO GROUND AT CLUTCH KR the measured resistance value of the valve is out of limit, the voltage at KR valve is too low. cable / connector is defective and has








gearbox

1) see chapter 4

89 5530 5 O.C. AT CLUTCH KR the measured resistance value of the valve is out of limit. cable / connector is defective and has






gearbox

1) see chapter 4

8A 5535 4 S.C. TO GROUND AT DLM TRANSVERSAL OUTPUT TCU detected a wrong voltage at the output pin, that looks like a s.c. to vehicle ground cable is defective and is contacted to

vehicle ground device has an internal defect connector pin is contacted to vehicle

output will be on until TCU power down even if fault vanishes (loose connection) OP-Mode: normal

check the cable from TCU to the valve check the connectors check the resistance of valve

1) see chapter 4



Fault Code (hex)



ground

8B 5535 3 S.C. TO BATTERY VOLTAGE AT DLM TRANSVERSAL OUTPUT TCU detected a wrong voltage at the output pin, that looks like a s.c. to battery voltage cable is defective and is contacted to

battery voltage device has an internal defect connector pin is contacted to battery

voltage



1) see chapter 4

8C 5535 5 O.C. AT DLM TRANSVERSAL OUTPUT TCU detected a wrong voltage at the output pin, that looks like a o.c. for this output pin cable is defective and has no

connection to TCU device has an internal defect connector has no connection to TCU



1) see chapter 4

8D 5536 4 S.C. TO GROUND AT DLM INDICATOR LAMP OUTPUT TCU detected a wrong voltage at the output pin, that looks like a s.c. to vehicle ground cable is defective and is contacted to


ground


check the cable from TCU to the device check the connectors check the resistance of device

1) see chapter 4

8E 5536 3 S.C. TO BATTERY VOLTAGE AT DLM INDICATOR LAMP OUTPUT


check the cable from TCU to the device check the connectors

1) see chapter 4



Fault Code (hex)



TCU detected a wrong voltage at the output pin, that looks like a s.c. to battery voltage cable is defective and is contacted to


voltage

check the resistance of device

8F 5536 5 O.C. DLM INDICATOR LAMP OUTPUT

TCU detected a wrong voltage at the output pin, that looks like a o.c. for this output pin cable is defective and has no



check the cable from TCU to the device check the connectors check the resistance of device

1) see chapter 4

91 5560 4 S.C. TO GROUND AT RELAY REVERSE WARNING ALARM TCU detected a wrong voltage at the output pin, that looks like a s.c. to vehicle ground cable is defective and is contacted to

vehicle ground backup alarm device has an internal


ground

backup alarm will be on until TCU power down even if fault vanishes (loose connection) OP-Mode: normal

check the cable from TCU to the backup alarm device

check the connectors from backup alarm device to TCU

check the resistance 1) of backup alarm device

1) see chapter 4

92 5560 3 S.C. TO BATTERY VOLTAGE AT RELAY REVERSE WARNING ALARM TCU detected a wrong voltage at the output pin, that looks like a s.c. to battery




1) see chapter 4



Fault Code (hex)



voltage cable is defective and is contacted to

battery voltage backup alarm device has an internal


voltage


93 5560 5 O.C. AT RELAY REVERSE WARNING ALARM TCU detected a wrong voltage at the output pin, that looks like a o.c. for this output pin cable is defective and has no

connection to TCU backup alarm device has an internal

defect connector has no connection to TCU





1) see chapter 4

94 5570 4 S.C. TO GROUND AT RELAY STARTER INTERLOCK TCU detected a wrong voltage at the output pin, that looks like a s.c. to vehicle ground cable is defective and is contacted to

vehicle ground starter interlock relay has an internal


ground


check the cable from TCU to the starter interlock relay

check the connectors from starter interlock relay to TCU

check the resistance 1) of starter interlock relay

1) see chapter 4

95 5570 3 S.C. TO BATTERY VOLTAGE AT RELAY STARTER INTERLOCK TCU detected a wrong voltage at the output pin, that looks like a s.c. to battery voltage




check the resistance 1) of starter

1) see chapter 4



Fault Code (hex)



cable is defective and is contacted to battery voltage

starter interlock relay has an internal defect

connector pin is contacted to battery voltage

interlock relay

96 5570 5 O.C. AT RELAY STARTER INTERLOCK TCU detected a wrong voltage at the output pin, that looks like a o.c. for this output pin cable is defective and has no

connection to TCU starter interlock relay has an internal

defect connector has no connection to TCU




check the resistance 1) of starter interlock relay

1) see chapter 4

A4 5620 4 S.C. TO GROUND AT WARNING SIGNAL OUTPUT TCU detected a wrong voltage at the output pin, that looks like a s.c. to vehicle ground cable is defective and is contacted to

vehicle ground warning device has an internal defect connector pin is contacted to vehicle

ground

no reaction OP-mode: normal

check the cable from TCU to the warning device

check the connectors from warning device to TCU

check the resistance 1) of warning device

1) see chapter 4

A5 5620 5 O.C. AT WARNING SIGNAL OUTPUT TCU detected a wrong voltage at the output pin, that looks like a o.c. for this output pin cable is defective and has no

connection to TCU warning device has an internal defect





1) see chapter 4



Fault Code (hex)



connector has no connection to TCU

A6 5620 3 S.C. TO BATTERY VOLTAGE AT WARNING SIGNAL OUTPUT TCU detected a wrong voltage at the output pin, that looks like a s.c. to battery voltage cable is defective and is contacted to

battery voltage warning device has an internal defect connector pin is contacted to battery

voltage





1) see chapter 4

B1 5660 2 SLIPPAGE AT CLUTCH K1 TCU calculates a differential speed at closed clutch K1. If this calculated value is out of range, TCU interprets this as slipping clutch. low pressure at clutch K1 low main pressure wrong signal at internal speed sensor wrong signal at output speed sensor wrong size of the sensor gap clutch is defective


check pressure at clutch K1 check main pressure in the system check sensor gap at internal speed

sensor

check sensor gap at output speed sensor check signal at internal speed sensor check signal at output speed sensor replace clutch

B2 5665 2 SLIPPAGE AT CLUTCH K2 TCU calculates a differential speed at closed clutch K2. If this calculated value is out of range, TCU interprets this as slipping clutch. low pressure at clutch K2 low main pressure wrong signal at internal speed sensor wrong signal at output speed sensor wrong size of the sensor gap



sensor




Fault Code (hex)



clutch is defective

B3 5670 2 SLIPPAGE AT CLUTCH K3 TCU calculates a differential speed at closed clutch K3. If this calculated value is out of range, TCU interprets this as slipping clutch. low pressure at clutch K3 low main pressure wrong signal at internal speed sensor wrong signal at output speed sensor wrong size of the sensor gap clutch is defective



sensor


B4 5675 2 SLIPPAGE AT CLUTCH K4 TCU calculated a difference speed at TCU calculates a differential speed at closed clutch K4. If this calculated value is out of range, TCU interprets this as slipping clutch. low pressure at clutch K4 low main pressure wrong signal at internal speed sensor wrong signal at turbine speed sensor wrong size of the sensor gap clutch is defective



sensor

check sensor gap at turbine speed sensor check signal at internal speed sensor check signal at turbine speed sensor replace clutch

B5 5680 2 SLIPPAGE AT CLUTCH KV TCU calculates a differential speed at closed clutch KV. If this calculated value is out of range, TCU interprets this as slipping clutch. low pressure at clutch KV low main pressure wrong signal at internal speed sensor


check pressure at clutch KV check main pressure in the system check sensor gap at internal speed

sensor




Fault Code (hex)



wrong signal at turbine speed sensor wrong size of the sensor gap clutch is defective

B6 5685 2 SLIPPAGE AT CLUTCH KR TCU calculates a differential speed at closed clutch KR. If this calculated value is out of range, TCU interprets this as slipping clutch. low pressure at clutch KR low main pressure wrong signal at internal speed sensor wrong signal at turbine speed sensor wrong size of the sensor gap clutch is defective


check pressure at clutch KR check main pressure in the system check sensor gap at internal speed

sensor


B7 5700 0 OVERTEMP SUMP TCU measured a temperature in the oil sump that is over the allowed threshold.


cool down machine check oil level check temperature sensor

BA 5730 0 DIFFERENTIAL PRESSURE OIL FILTER TCU measured a voltage at differential pressure switch out of the allowed range oil filter is polluted cable/connector is broken or

cable/connector is contacted to battery voltage or vehicle ground

differential pressure switch is defective


check oil filter check wiring from TCU to differential

pressure switch check differential pressure switch

(measure resitance)

BC 5745 15 OVERSPEED OUTPUT TCU messures an transmission output speed above the defined threshold

No reaction OP-Mode: normal

C0 5751 0 ENGINE TORQUE OR ENGINE POWER OVERLOAD TCU calculates an engine torque or engine

OP-Mode: normal



Fault Code (hex)



power above the defined thresholds C1 5752 0 TRANSMISSION OUTPUT TORQUE

OVERLOAD TCU calculates an transmission output torque above the defined threshold

OP-Mode: normal

C2 5755 15 TRANSMISSION INPUT TORQUE OVERLOAD TCU calculates an transmission input torque above the defined threshold

programmable :No reaction or shift to neutral OP-Mode: normal

C3 5760 0 OVERTEMP CONVERTER OUTPUT TCU measured a oil temperature at the converter ouput that is over the allowed threshold.


cool down machine check oil level check temperature sensor

C4 5770 4 S.C. TO GROUND AT JOYSTICK STATUS INDICATOR TCU detected a wrong voltage at the output pin, that looks like a s.c. to vehicle ground cable is defective and is contacted to

vehicle ground joystick status indicator has an

internal defect connector pin is contacted to vehicle

ground


check the cable from TCU to joystick status indicator

check the connectors from joystick status indicator to TCU

check the resistance 1) of joystick status indicator

C5 5770 3 S.C. TO BATTERY VOLTAGE AT JOYSTICK STATUS INDICATOR TCU detected a wrong voltage at the output pin, that looks like a s.c. to battery voltage cable is defective and is contacted to

battery voltage joystick status indicator has an

internal defect connector pin is contacted to battery







Fault Code (hex)



voltage

C6 5770 5 O.C. AT JOYSTICK STATUS INDICATOR TCU detected a wrong voltage at the output pin, that looks like a o.c. for this output pin cable is defective and has no

connection to TCU joystick status indicator has an

internal defect connector has no connection to TCU





C7 5780 4 S.C. TO GROUND AT OVERTEMP NEUTRAL INDICATOR TCU detected a wrong voltage at the output pin, that looks like a s.c. to vehicle ground cable is defective and is contacted to

vehicle ground overtemp status indicator has an

internal defect connector pin is contacted to vehicle

ground


check the cable from TCU to OVERTEMP NEUTRAL INDICATOR

check the connectors from OVERTEMP NEUTRAL INDICATOR to TCU

check the resistance 1) of OVERTEMP NEUTRAL INDICATOR

C8 5780 3 S.C. TO BATTERY VOLTAGE AT OVERTEMP NEUTRAL INDICATOR TCU detected a wrong voltage at the output pin, that looks like a s.c. to battery voltage cable is defective and is contacted to

battery voltage overtemp status indicator has an

internal defect connector pin is contacted to battery







Fault Code (hex)



voltage

C9 5780 5 O.C. AT OVERTEMP NEUTRAL INDICATOR TCU detected a wrong voltage at the output pin, that looks like a o.c. for this output pin cable is defective and has no

connection to TCU OVETEMP status indicator has an

internal defect connector has no connection to TCU





CA 5790 9 ENGINE_RETARDER CONFIG_TIMEOUT Timeout of CAN-message ENGINE_RETARDER CONFIG from EEC controller interference on CAN-Bus CAN wire/connector is broken CAN wire/connector is defective an




CB 5800 9 ERC1 TIMEOUT Timeout of CAN-message ERC1 from EEC controller interference on CAN-Bus CAN wire/connector is broken CAN wire/connector is defective an




D1 5810 3 S.C. TO BATTERY VOLTAGE AT POWER SUPPLY FOR SENSORS TCU measures more than 6V at the pin

see fault codes no. 21 to 2C check cables and connectors to sensors, which are supplied from AU1

check the power supply at the pin AU1

fault codes no. 21 to no. 2C may be a reaction of this fault



Fault Code (hex)



AU1 (5V sensor supply)

(should be appx. 5V)

D2 5810 4 S.C. TO GROUND AT POWER SUPPLY FOR SENSORS TCU measures less than 4V at the pin AU1 (5V sensor supply)

see fault codes no. 21 to 2C check cables and connectors to sensors, which are supplied from AU1

check the power supply at the pin AU1 (should be appx. 5V)

fault codes no. 21 to no. 2C may be a reaction of this fault

D3 5820 4 LOW VOLTAGE AT BATTERY measured voltage at power supply is lower than 10 V (12V device) lower than 18 V (24V device)

shift to neutral OP-Mode: TCU shutdown

check power supply battery check cables from batteries to TCU check connectors from batteries to TCU

D4 5820 3 HIGH VOLTAGE AT BATTERY measured voltage at power supply is higher than 18 V (12V device) higher than 32.5 V (24V device)


check power supply battery check cables from batteries to TCU check connectors from batteries to TCU

D5 5830 2 ERROR AT VALVE POWER SUPPLY VPS1 TCU switched on VPS1 and measured VPS1 is off or TCU switched off VPS1 and measured VPS1 is still on cable or connectors are defect and are

contacted to battery voltage cable or connectors are defect and are

contacted to vehicle ground permanent power supply KL30 missing TCU has an internal defect


check fuse check cables from gearbox to TCU check connectors from gearbox to TCU replace TCU

D6 5840 2 ERROR VALVE POWER SUPPLY VPS2 TCU switched on VPS2 and measured VPS2 is off or TCU switched off VPS2 and measured VPS2 is still on cable or connectors are defect and are

contacted to battery voltage cable or connectors are defect and are

contacted to vehicle ground permanent power supply KL30 missing


check fuse check cables from gearbox to TCU check connectors from gearbox to TCU replace TCU



Fault Code (hex)



TCU has an internal defect

D7 5545 4 S.C. TO GROUND AT DLM LONGITUDINAL OUTPUT TCU detected a wrong voltage at the output pin, that looks like a s.c. to vehicle ground cable is defective and is contacted to


ground



1) see chapter 4

D8 5545 3 S.C. TO BATTERY VOLTAGE AT DLM LONGITUDINAL OUTPUT TCU detected a wrong voltage at the output pin, that looks like a s.c. to battery voltage cable is defective and is contacted to


voltage



1) see chapter 4

D9 5545 5 O.C. AT DLM LONGITUDINAL OUTPUT TCU detected a wrong voltage at the output pin, that looks like a o.c. for this output pin cable is defective and has no




1) see chapter 4

E3 5860 3 S.C. TO BATTERY VOLTAGE AT DISPLAY OUTPUT


check the cable from TCU to the display check the connectors at the display



Fault Code (hex)



TCU sends data to the display and measures allways a high voltage level on the connector cable or connectors are defective and

are contacted to battery voltage display has an internal defect

change display

E4 5860 4 S.C. TO GROUND AT DISPLAY OUTPUT TCU sends data to the display and measures allways a high voltage level on the connector cable or connectors are defective and

are contacted to vehicle ground display has an internal defect


check the cable from TCU to the display check the connectors at the display change display

F1 5890 2 GENERAL EEPROM FAULT TCU can't read non volantile memoy TCU is defective


replace TCU often shown together with fault code F2

F2 5900 13 CONFIGURATION LOST TCU has lost the correct configuration and can't control the transmission. interference during saving data on non

volatile memory TCU is brand new or from another

vehicle

transmission stay neutral OP-Mode: TCU shutdown

Reprogramm the correct configuration for the vehicle (e.g. with cluster controller,...)

F3 5910 13 APPLICATION ERROR something of this application is wrong


replace TCU !! This fault occurs only if an test engineer did something wrong in the application of the vehicle

F5 5930 7 CLUTCH FAILURE AEB was not able to adjust clutch filling parameters One of the AEB-Values is out of limit


check clutch TCU shows also the affected clutch on the Display



Fault Code (hex)



F6 5930 13 CLUTCH ADJUSTMENT DATA LOST OR INCHPEDAL CALIBRATION DATA LOST TCU was not able to read correct clutch adjustment parameters interference during saving data on non

volatile memory TCU is brand new

default values = 0 for AEB offsets used OP-Mode: normal no Inchmode available

execute AEB

F7 5940 11 SUBSTITUTE CLUTCH CONTROL transmission input torque wrong engine retarder torque wrong speed signal(s) defective

OP-Mode : substitute clutch control

check engine retarder torque check speed sensors



4 measuring of resistance at actuator/sensors and cable

4.1 actuator:

R

2

1

G

open circuit: R12 R1G R2G short cut to ground: R12 R; R1G 0, R2G R or R1G R, R2G 0 (for s.c. to ground, G is connected to vehicle ground) short cut to battery: R12 R; R1G 0, R2G R or R1G R, R2G 0 (for s.c. to battery, G is connected to battery voltage)

4.2 cable:

P (power supply)

1 2

TCUActuator /Sensor

UBat

Gnd

C (chassis)

open circuit: R12 R1P R1C R2P R2C short cut to ground: R12 0; R1C R2C 0, R1P R2P short cut to battery: R12 0, R1C R2C , R1P R2P 0

Zf Fault Codes Latest

Documents

Transcript of Zf Fault Codes Latest

Группа компаний КОРОБКИ ОТБОРА МОЩНОСТИomfb.ru/katalog/kom/zf/01006100176.pdf · * zf 6s - 850/6,72-0,79 ** zf 16s - 151 to/13,8-0,84 - Без интардера

A Fault-Tolerant Dynamic Time-Triggered Protocol - Jens Christian

ZF SI Oelwechselkit 50145 V102 EN - ZF Friedrichshafen · ZF 5HP/6HP automatic transmission ZF Friedrichshafen AG ZF Services Obere Weiden 12, 97424 Schweinfurt, ... 6HP26 X BMW x

12115-1-03 ZF Compliance Guideline A4 alleSprachen 1807 …€¦ · ZF Friedrichshafen AG ZF Forum | Headquarters Löwentaler Straße 20 88046 Friedrichshafen Tyskland twitter.com/zf_konzern

INVERSE SIMULATION AS A TOOL FOR FAULT DETECTION ...

FAULT CODE LISTING FOR ZF WG110 TRANSMISSIONwinget.co.uk/document/ZF WG110 TRANSMISSION FAULT CODES.pdf · fault code listing for zf wg110 transmission winget limited po box 41 edgefold

ALLES WIRD ANDERS - ZF · 2020. 5. 29. · DAS ZF-MAGAZIN 1.2017 drive DAS ZF-MAGAZIN KÜNSTLICHE INTELLIGENZ ZF lehrt Autos das Denken SICHERHEIT Ein Algorithmus als Schutzengel

Workshop zf l_web_20_ceb_100326_final

© ZF Friedrichshafen AG, 20151ZF hilft, Öffentlich ZF Friedrichshafen AG ZF hilft 100 Jahre – 100 Schulen.

Kapitel Montagezahnstangen Companion racks ZF-2 ...€¦ · Montagezahnstangen Companion racks ZF-2 Zahnstangenbefestigung Rack mounting ZF-3 Zahnstangen Montageset Rack assembly

Ch.03 Fault Management

Fault Is Of The Sufferer(German)

Fault Tolerant Control Schemes for Wireless Networked Control … · 2014-11-04 · Fault Tolerant Control Schemes for Wireless Networked Control Systems with an Integrated Scheduler

Zf Astronic Esp

Zf april 2014

ZF Transmission EST37 fault codes

ZF Friedrichshafen AG Division Active & Passive Safety ... · PDF file1 © ZF Friedrichshafen AG, 2016 ZF Friedrichshafen AG ZF Friedrichshafen AG Division Active & Passive Safety

VMware vSphere 5 - Amazon Simple Storage Service · B VMware-vShield-Zones-Produktfamilie ... 5.5 Fault Tolerance ..... 198 5.5.1 Wie funktioniert Fault Tolerance ...

Portable Insulation Fault Location System ... - Bender … · EDS3365 and EDS3360 Portable Insulation Fault Location System for IT AC and DC Systems and Residual Current Measurements

SICHERHEITSDATENBLATT Produktname: ZF …...SICHERHEITSDATENBLATT gemäß Verordnung (EG) Nr. 1907/2006 (REARCH-Verordnung) Produktname: ZF-Ecofluid HV ZF Friedrichshafen AG • ZF