Post on 01-Nov-2019
E 0 ~
~ 0 0
Ci x w Cf) N
Physikalisch-Technische Bundesanstalt Braunschweig und Berlin
(1) EG-Baumusterprüfbescheinigung (2) Geräte und Schutzsysteme zur bestimmungsgemäßen Verwendung
in explosionsgefährdeten Bereichen - Richtlinie 94/9/EG (3) EG-Baumusterprüfbescheinigungsnummer
PTB 13 ATEX 2007 X (4) Gerät: Explosionsgeschützter Messumformer für Druck
SITRANS PDS III Hart, SITRANS PDS III-PA, SITRANS PDS III-FF
(5)
(6)
(7)
(8)
Typen 7MF4*** - * ++ * * - *B+ * und 7MF4*** - * ++ * * - *E+ *
Hersteller: Siemens AG 1 ndustry Seetor lndustry Automation Division
Anschrift: 76181 Karlsruhe, Deutschland
Die Bauart dieses Gerätes sowie die verschiedenen zulässigen Ausführungen sind in der Anlage und den darin aufgeführten Unterlagen zu dieser Baumusterprüfbescheinigung festgelegt.
Die Physikalisch-Technische Bundesanstalt bescheinigt als benannte Stelle Nr. 0102 nach Artikel 9 der Richtlinie des Rates der Europäischen Gemeinschaften vom 23. März 1994 (94/9/EG) die Erfüllung der grundlegenden Sicherheits- und Gesundheitsanforderungen für die Konzeption und den Bau von Geräten und Schutzsystemen zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen gemäß Anhang II der Richtlinie.
Die Ergebnisse der Prüfung sind in dem vertraulichen Prüfbericht PTB Ex 13-22337 festgehalten.
(9) Die grundlegenden Sicherheits- und Gesundheitsanforderungen werden erfüllt durch Übereinstimmung mit
EN 60079-0:2009 EN 60079-11 :2012 EN 60079-15:2010 EN 60079-26:2007 (10) Falls das Zeichen „X" hinter der Bescheinigungsnummer steht, wird auf besondere Bedingungen für die
sichere Anwendung des Gerätes in der Anlage zu dieser Bescheinigung hingewiesen.
(11) Diese EG-Baumusterprüfbescheinigung bezieht sich nur auf Konzeption und Prüfung des festgelegten Gerätes gemäß Richtlinie 94/9/EG. Weitere Anforderungen dieser Richtlinie gelten für die Herstellung und das Inverkehrbringen dieses Gerätes. Diese Anforderungen werden nicht durch diese Bescheinigung abgedeckt.
(12) Die Kennzeichnung des Gerätes muss die folgenden Angaben enthalten:
@ 111/2 G Ex ia llC T4/T5/T6 Ga 111/2 G Ex ib llC T4/T5/T6 Gb II 2/3 G Ex nA llC T4/T5/T6 Ge II 2/3 G Ex ie llC T4/T5/T6 Ge II 3 G Ex nA llC T4/T5/T6 Ge II 3 G Ex ie llC T4/T5/T6 Ge
Zertifizierungssektor Explosionsschutz Braunschweig, 23. September 2013
Seite 1/7
EG-Baumu f, !~ einigungen ohne Unterschrift und ohne Siegel haben keine Gültigkeit. Diese EG-Baumusterprüfbescheinigung darf nur unverändert weiterverbreitet werden.
Auszüge oder Änderungen bedürfen der Genehmigung der Physikalisch-Technischen Bundesanstalt.
Physikalisch-Technische Bundesanstalt• Bundesallee 100 • 38116 Braunschweig • DEUTSCHLAND
Physikalisch-Technische Bundesanstalt Braunschweig und Berlin
(13) A n 1 a g e
(14) EG-Baumusterprüfbescheinigung PTB 13 ATEX 2007 X
(15) Beschreibung des Gerätes
Der explosionsgeschützte Messumformer für Druck SITRANS P OS III Hart, SITRANS POS 111-PA, SITRANS P OS III-FF, Typen 7MF4*** - * ++ * * - *B+ * und 7MF4*** - * ++ * * - *E+ * dient zur Messung nicht-aggressiver und aggressiver Gase, Dämpfe und Flüssigkeiten. Das Gerät besteht aus den Komponenten Gehäuse, Elektronikeinheit und Messzelle. Der zu messende Druck wird über eine Trennmembran und ein mit Öl gefülltes System an die hermetisch dichte Sensoreinheit übertragen. Dieser Aufbau gewährleistet eine Trennung der Bereiche voneinander, in denen Betriebsmittel der Kategorien 1/2 bzw. 2/3 erforderlich sind.
Das Messsignal wird in der Elektronikeinheit aufbereitet und steht als eingeprägter Gleichstrom 4-20 mA (HART) oder Bussignal (FF oder Profibus-PA) zur Verfügung.
Kategorie-1 /2-Betriebsm ittel
Das Elektronikgehäuse wird in explosionsgefährdeten Bereichen errichtet, die ein Betriebsmittel der Kategorie 2 erfordern. Die Prozessanschlusselemente werden in die Trennwand errichtet, die die Bereiche voneinander trennt, in denen Betriebsmittel der Kategorie 1 oder 2 erforderlich sind.
Die Abhängigkeit der Temperaturklasse von der höchstzulässigen Temperatur des Mediums und der höchstzulässigen Umgebungstemperatur an der Elektronik ist der folgenden Tabelle zu entnehmen:
Temperaturklasse Temperatur des Mediums Umgebungstemperatur an der Elektronik
T4 -20 „. + 60 °C -40 „. +85 °C T5 -20 „. + 60 °C -40 „. +70 °C T6 -20 „. + 60 °C -40 „. +60 °C
Der Prozessdruck der Medien muss bei Anwendungen, die Kategorie-1-Betriebsmittel erfordern, zwischen 0,8 bar „.1, 1 bar liegen.
Die Einsatzbedingungen im Betrieb ohne explosionsfähige Gemische sind den Herstellerangaben zu entnehmen.
Seite 2/7
EG-Baumusterprüfbescheinigungen ohne Unterschrift und ohne Siegel haben keine Gültigkeit. Diese EG-Baumusterprüfbescheinigung darf nur unverändert weiterverbreitet werden.
Auszüge oder Änderungen bedürfen der Genehmigung der Physikalisch-Technischen Bundesanstalt.
Physikalisch-Technische Bundesanstalt• Bundesallee 100 • 38116 Braunschweig •DEUTSCHLAND
Physikalisch-Technische Bundesanstalt Braunschweig und Berlin
Anlage zur EG-Baumusterprüfbescheinigung PTB 13 ATEX 2007 X
Kategorie-2-Betriebsmittel
Die Messumformer werden in explosionsgefährdeten Bereichen errichtet, die ein Betriebsmittel der Kategorie 2 erfordern.
Die höchstzulässige Umgebungstemperatur in Abhängigkeit von der Temperaturklasse ist der folgenden Tabelle zu entnehmen:
Temperaturklasse Umgebungstemperatur T4 -40 „. +85 °C T5 -40 „. +70 °C T6 -40 „. +60 °C
Die zulässigen Betriebstemperaturen und Drücke für den Betrieb sind den Herstellerangaben zu entnehmen.
Kategorie-2/3-Betriebsmittel
Das Elektronikgehäuse wird in explosionsgefährdeten Bereichen errichtet, die ein Betriebsmittel der Kategorie 3 erfordern. Die Prozessanschlusselemente werden in die Trennwand errichtet, die die Bereiche voneinander trennt, in denen Betriebsmittel der Kategorie 2 oder 3 erforderlich sind.
Die höchstzulässige Umgebungstemperatur in Abhängigkeit von der Temperaturklasse ist der folgenden Tabelle zu entnehmen:
T em peratu rklasse Umgebungstemperatur T4 -40 „. +85 °C T5 -40 „. +70 °C T6 -40 „. +60 °C
Die Einsatzbedingungen im Betrieb ohne explosionsfähige Gemische sind den Herstellerangaben zu entnehmen.
Kategorie-3-Betriebsmittel
Die Messumformer werden in explosionsgefährdeten Bereichen errichtet, die ein Betriebsmittel der Kategorie 3 erfordern„
Die höchstzulässige Umgebungstemperatur in Abhängigkeit von der Temperaturklasse ist der folgenden Tabelle zu entnehmen:
T em peratu rklasse Umgebungstemperatur T4 -40 „. +85 °C T5 -40 „. +70 °C T6 -40 „. +60 °C
Die zulässigen Betriebstemperaturen und Drücke für den Betrieb sind den Herstellerangaben zu entnehmen.
Seite 3/7
EG-Baumusterprüfbescheinigungen ohne Unterschrift und ohne Siegel haben keine Gültigkeit. Diese EG-Baumusterprüfbescheinigung darf nur unverändert weiterverbreitet werden.
Auszüge oder Änderungen bedürfen der Genehmigung der Physikalisch-Technischen Bundesanstalt.
Physikalisch-Technische Bundesanstalt• Bundesallee 100 • 38116 Braunschweig• DEUTSCHLAND
Physikalisch-Technische Bundesanstalt Braunschweig und Berlin
Anlage zur EG-Baumusterprüfbescheinigung PTB 13 ATEX 2007 X
Elektrische Daten
Variante Kennzeichnung
SITRANS P DS 111, Typ 7MF4*33-*++**-*B+* II 1/2 G Ex ia llC T4/T5/T6 Ga II 1/2 G Ex ib llC T4/T5/T6 Gb
Hilfsenergie-/Ausgangssignalstromkreis (Anschluss: +,-)
Varianten
in Zündschutzart Eigensicherheit Ex ia llC bzw. Ex ib llC
nur zum Anschluss an einen bescheinigten eigensicheren Stromkreis
Höchstwerte: Ui = 30 V li = 100 mA Pi = 750 mW
Li = 0,4 mH Ci = 6 nF
Kennzeichnung Caültig für beide Varianten)
SITRANS POS III PA, Typ 7MF4*34-*++**-*B+* II 1/2 G Ex ia llC T4/T5/T6 Ga SITRANS PDS III FF, Typ 7MF4*35-*++**-*B+* II 1/2 G Ex ib llC T4/T5/T6 Gb
Hilfsenergie-/Ausgangssignalstromkreis (Anschluss: +, -)
in Zündschutzart Eigensicherheit Ex ia llC bzw. Ex ib llC
nur zum Anschluss an einen bescheinigten eigensicheren Stromkreis (z.B. FISCO-Speisegerät oder eine lineare Barriere) mit den Höchstwerten entsprechend folgender Tabelle:
FISCO-Speisegerät lineare Barriere ia I ib ia I ib
ui 17,5 V 24 V
li 380 mA 174 mA
pi 5,32W 1W
Li = 7 µH Ci = 1, 1 nF
Seite 4/7
EG-Baumusterprüfbescheinigungen ohne Unterschrift und ohne Siegel haben keine Gültigkeit. Diese EG-Baumusterprüfbescheinigung darf nur unverändert weiterverbreitet werden.
Auszüge oder Änderungen bedürfen der Genehmigung der Physikalisch-Technischen Bundesanstalt.
Physikalisch-Technische Bundesanstalt• Bundesallee 100 • 38116 Braunschweig • DEUTSCHLAND
Physikalisch-Technische Bundesanstalt Braunschweig und Berlin
Anlage zur EG-Baumusterprüfbescheinigung PTB 13 ATEX 2007 X
Varianten Kennzeichnung (gültig für alle drei Varianten)
SITRANS P DS III, Typ 7MF4*33-*++**-*B+* II 1/2 G Ex ia llC T4/T5/T6 Ga SITRANS PDS III PA, Typ 7MF4*34-*++**-*B+* II 1/2 G Ex ib llC T4/T5/T6 Gb SITRANS PDS III FF, Typ 7MF4*35-*++**-*B+*
Kontrollanzeiger- Signalstromkreis (Anschluss: Steckkontakte, Flachstecker)
Messzellenstrom kreis
Variante
in Zündschutzart Eigensicherheit Ex ia llC bzw. Ex ib llC
nur zum Anschluss an erdfreie Anzeiger oder Prüfgeräte ohne eigene Stromversorgung (Batterie, Netz) und ohne Fremdstromkreise oder zum Anschluss von Prüfgeräten, die für den explosionsgefährdeten Bereich zugelassen sind.
Höchstwerte der Zusammenschaltung von Kontrollanzeiger-Signalstromkreis und Prüfgerät:
Ui = 30 V li = 100 mA Pi = 750 mW
llC L0 mH 0,5 C0 nF 3
geräteintern, keine Schnittstelle nach außen.
KennzeichnunQ
SITRANS P DS III, Typ 7MF4*33-*++**-*E+* II 2/3 G Ex nA llC T4/T5/T6 Ge II 3 G Ex nA llC T4/T5/T6 Ge
Hilfsenergie-/Ausgangssignalstromkreis
(Anschluss: +,-)
Variante
in Zündschutzart Nichtfunkend Ex nA II
Um = 45 V
Kennzeichnung
SITRANS P DS III, Typ 7MF4*33-*++**-*E+* II 2/3 G Ex ic llC T4/T5/T6 Ge II 3 G Ex ic llC T4/T5/T6 Ge
Hilfsenergie-/Ausgangssignalstromkreis (Anschluss: +,-)
in Zündschutzart Eigensicherheit Ex ic llC
Höchstwerte: Ui = 45 V
Li = 0,4 mH Ci = 6 nF
EG-Baumusterprüfbescheinigungen ohne Unterschrift und ohne Siegel haben keine Gültigkeit. Diese EG-Baumusterprüfbescheinigung darf nur unverändert weiterverbreitet werden.
Auszüge oder Änderungen bedürfen der Genehmigung der Physikalisch-Technischen Bundesanstalt.
Physikalisch-Technische Bundesanstalt • Bundesallee 100 • 38116 Braunschweig • DEUTSCHLAND
Seite 5/7
Physikalisch-Technische Bundesanstalt Braunschweig und Berlin
Anlage zur EG-Baumusterprüfbescheinigung PTB 13 ATEX 2007 X
Kennzeichnung Varianten (gültig für beide Varianten)
SITRANS POS III PA, Typ 7MF4*34-*++**-*E+* 11 2/3 G Ex nA llC T4/T5/T6 Ge SITRANS POS III FF, Typ 7MF4*35-*++**-*E+* II 3 G Ex nA llC T4/T5/T6 Ge
Hilfsenergie-/Ausgangssignalstromkreis (Anschluss: +,-)
Varianten
in Zündschutzart Nichtfunkend Ex nA 11
Um = 32 V (max. Busspannung)
Kennzeichnung (gültig für beide Varianten)
SITRANS POS III PA, Typ 7MF4*34-*++**-*E+* II 2/3 G Ex ic llC T4/T5/T6 Ge SITRANS POS III FF, Typ 7MF4*35-*++**-*E+* II 3 G Ex ic llC T4/T5/T6 Ge
in Zündschutzart Eigensicherheit Ex ic llC Hilfsenergie-/Ausgangssignalstromkreis (Anschluss: +,-)
zum Anschluss an ein FISCO-Speisegerät gemäß EN 60079-11 :2012 oder eine lineare Barriere mit den Werten entsprechend folgender Tabelle:
FISCO-Speisegerät lineare Barriere ic ic
ui 17,5 V 32 V
li 570mA 132 mA
pi 1W
Li = 7 µH Ci = 1, 1 nF
(16) Prüfbericht PTB Ex 13-22337
(17) Besondere Bedingungen
1. Der Anschluss für den Potenzialausgleichsleiter des Messumformers SITRANS P OS III ist bei nichteigensicheren Varianten (Zündschutzart Ex nA) mit dem Potenzialausgleichssystem des explosionsgefährdeten Bereiches elektrisch zu verbinden. Die eigensicheren Varianten sind in geeigneter Weise elektrostatisch zu erden.
2. Steckvorrichtungen oder Steckverbinder zum Anschluss äußerer Stromkreise sind für den Einsatz als Kategorie 3-Gerät in der Zündschutzart „Nichtfunkend" (nA) nicht zulässig.
3. Bei Anschluss an eigensichere Stromkreise der Kategorie „ib" und gleichzeitigem Einsatz als Trennwandgerät zwischen Bereichen, die ein Kategorie 1- bzw. Kategorie 2-Gerät erfordern, hängt der Explosionsschutz des Messumformers insbesondere von der Dichtheit der Trennmembran ab. Unter diesen Betriebsbedingungen darf der Messumformer nur für solche brennbaren Medien verwendet werden, gegen die die Trennmembran hinreichend chemisch und gegen Korrosion beständig ist.
Seite 6/7
EG-Baumusterprüfbescheinigungen ohne Unterschrift und ohne Siegel haben keine Gültigkeit. Diese EG-Baumusterprüfbescheinigung darf nur unverändert weiterverbreitet werden.
Auszüge oder Änderungen bedürfen der Genehmigung der Physikalisch-Technischen Bundesanstalt.
Physikalisch-Technische Bundesanstalt • Bundesallee 100 • 38116 Braunschweig • DEUTSCHLAND
Physikalisch-Technische Bundesanstalt Braunschweig und Berlin
Anlage zur EG-Baumusterprüfbescheinigung PTB 13 ATEX 2007 X
(18) Grundlegende Sicherheits- und Gesundheitsanforderungen
erfüllt durch Übereinstimmung mit den vorgenannten Normen
Zertifizierungssektor Explosionsschutz Braunschweig, 23. September 2013 Im Auftrc;ig r"· l..l--
u?
Seite 7/7
EG-Baumusterprüfbescheinigungen ohne Unterschrift und ohne Siegel haben keine Gültigkeit. Diese EG-Baumusterprüfbescheinigung darf nur unverändert weiterverbreitet werden.
Auszüge oder Änderungen bedürfen der Genehmigung der Physikalisch-Technischen Bundesanstalt.
Physikalisch-Technische Bundesanstalt • Bundesallee 100 • 38116 Braunschweig • DEUTSCHLAND
J:l
"C -0 -0
~ ~
PIB Physikalisch-Technische Bundesanstalt Braunschweig und Berlin Nationales Metrologieinstitut
1. ERGÄNZUNG gemäß Richtlinie 94/9/EG Anhang III Ziffer 6
zur EG-Baumusterprüfbescheinigung PTB 13 ATEX 2007 X
Gerät: Explosionsgeschützter Messumformer für Druck SITRANS PDS III Hart, SITRANS PDS III-PA, SITRANS P DS 111-FF Typen 7MF4*** - * ++ * * - *B+ * und 7MF4*** - * ++ * * - *E+ *
Kennzeichnung: @ 111/2 G II 2/3 G 113 G
Ex ia llC T 4/T5/T6 Ga Ex nA llC T 4/T5/T6 Ge Ex nA llC T4/T5/T6 Ge
111/2 G II 2/3 G 113 G
Ex ib llC T4/T5/T6 Gb Ex ic llC T 4/T5/T6 Ge Ex ic llC T 4/T5/T6 Ge
Hersteller:
Anschrift:
Siemens AG - Process lndustries and Drives
vormals
Siemens AG lndustry Seetor lndustry Automation Division
76181 Karlsruhe, Deutschland
Beschreibung der Ergänzungen und Änderungen
Die explosionsgeschützten Messumformer für Druck SITRANS P DS III Hart, SITRANS P DS 111-PA, SITRANS P DS 111-FF, Typen 7MF4*** - * ++ * * - *B+ * und 7MF4*** - * ++ * * - *E+ * dürfen künftig auch nach den im Prüfbericht aufgeführten Prüfungsunterlagen gefertigt und betrieben werden. Die Änderungen betreffen die Einführung der neuen Gerätevarianten SITRANS P410 Hart, SITRANS P410-PA, SITRANS P410-FF, Typen 7MF4*** - * ++ * * - *B+ * Z-C41 und 7MF4*** - * ++ * * - *E+ * Z-C41 sowie SITRANS P310 Hart, SITRANS P310-PA, SITRANS P310-FF, Typen 7MF2*** - * ++ * * - *B+ * und 7MF2*** - * ++ * * - *E+ * . Diese neuen Varianten unterscheiden sich von den bisherigen Typen jeweils in der Kalibriergenauigkeit (Software), die technische Ausführung bleibt unverändert.
Die elektrischen Daten und die „Besondere Bedingung" Nr.1 werden für die neuen Gerätevarianten erweitert.
Desweiteren erfolgt eine Anpassung an den aktuellen Normenstand sowie eine Änderung des Herstellernamens wie oben angegeben.
Seite 1/5
EG-Baumusterprüfbescheinigungen ohne Unterschrift und ohne Siegel haben keine Gültigkeit. Diese EG-Baumusterprüfbescheinigung darf nur unverändert weiterverbreitet werden.
Auszüge oder Änderungen bedürfen der Genehmigung der Physikalisch-Technischen Bundesanstalt.
Physikalisch-Technische Bundesanstalt • Bundesallee 100 • 38116 Braunschweig • DEUTSCHLAND
PTB Physlkallsch-Technische Bundesanstalt ' Braunschweig und Berlin
Nationales Metrologieinstitut
1. Ergänzung zur EG-Baumusterprüfbescheinigung PTB 13 ATEX 2007 X
Elektrische Daten
Varianten Kennzeichnung
SITRANS P OS III, Typ 7MF4*33-*++**-*B+* 111/2 G Ex ia llC T 4/T5/T6 Ga SITRANS P410, Typ 7MF4*33-*++**-*B+*Z-C41 SITRANS P310, Typ 7MF2*33-*++**-*B+*
111/2 G Ex ib llC T4/T5/T6 Gb
Hilfsenergie-/Ausgangssignalstromkreis (Anschluss: +,-)
in Zündschutzart Eigensicherheit Ex ia llC bzw. Ex ib llC
nur zum Anschluss an einen bescheinigten eigensicheren Stromkreis
Höchstwerte: Ui = 30 V li = 100 mA Pi = 750 mW
Li = Ci =
0,4 mH 6 nF
Varianten Kennzeichnung
SITRANS POS 111 PA, Typ 7MF4*34-*++**-*B+* SITRANS .P410-PA, Typ 7MF4*34-*++**-*B+*Z-C41 SITRANS P310-PA, Typ 7MF2*34-*++**-*B+* 111/2 G Ex ia llC T4/T5/T6 Ga
SITRANS POS III FF, Typ 7MF4*35-*++**-*B+* 111/2 G Ex ib llC T 4/T5/T6 Gb
SITRANS P410-FF, SITRANS P310-FF,
Hilfsenergie-/Ausgangssignalstromkreis (Anschluss: +, -)
Typ 7MF4*35-*++**-*B+*Z-C41 Typ 7MF2*35-*++**-*B+*
in Zündschutzart Eigensicherheit Ex ia llC bzw. Ex ib llC
nur zum Anschluss an einen bescheinigten eigensicheren Stromkreis (z.B. FISCO-Speisegerät oder eine lineare Barriere) mit den Höchstwerten entsprechend folgender Tabelle:
ui
11
pi
FISCO-Speisegerät
7 µH 1, 1 nF
ia I ib
17,5 V
380mA
5,32W
lineare Barriere ia I ib
24V
174 mA
1W
Seite 2/5
EG-Baumusterprüfbescheinigungen ohne Unterschrift und ohne Siegel haben keine Gültigkeit. Diese EG-Baumusterprüfbescheinigung darf nur unverändert weiterverbreitet werden.
Auszüge oder Änderungen bedürfen der Genehmigung der Physikalisch-Technischen Bundesanstalt.
Physikalisch-Technische Bundesanstalt• Bundesallee 100 • 38116 Braunschweig• DEUTSCHLAND
P1B Physikalisch-Technische Bundesanstalt ' Braunschweig und Berlin
Nationales Metrologieinstitut
1. Ergänzung zur EG-Baumusterprüfbescheinigung PTB 13 ATEX 2007 X
Varianten Kennzeichnung
SITRANS P DS III, Typ 7MF4*33-*++**-*B+* SITRANS P410, Typ 7MF4*33-*++**-*B+*Z-C41 SITRANS P310, Typ 7MF2*33-*++**-*B+*
SITRANS PDS III PA, Typ 7MF4*34-*++**-*B+* 111/2 G Ex ia llC T4/T5/T6 Ga SITRANS P410-PA, Typ 7MF4*34-*++**-*B+*Z-C41 SITRANS P310-PA, Typ 7MF2*34-*++**-*B+*
111/2 G Ex ib llC T4/T5/T6 Gb
SITRANS P DS III FF, Typ 7MF4*35-*++**-*B+* SITRANS P410-FF, Typ 7MF4*35-*++**-*B+*Z-C41 SITRANS P310-FF, Typ 7MF2*35-*++**-*B+*
in Zündschutzart Eigensicherheit Ex ia llC bzw. Ex ib llC
Kontrollanzeiger- Signalstromkreis (Anschluss: Steckkontakte, Flachstecker) nur zum Anschluss an erdfreie Anzeiger oder Prüfgeräte
ohne eigene Stromversorgung (Batterie, Netz) und ohne Fremdstromkreise oder zum Anschluss von Prüfgeräten, die für den explosionsgefährdeten Bereich zugelassen sind.
Messzellenstromkreis
Varianten
Höchstwerte der Zusammenschaltung von Kontrollanzeiger-Signalstromkreis und Prüfgerät:
Ui = 30 V li = 100 mA Pi = 750 mW
llC 0,5 3
geräteintern, keine Schnittstelle nach außen.
Kennzeichnung
SITRANS P DS III, Typ 7MF4*33-*++**-*E+* II 2/3 G Ex nA llC T 4/T5/T6 Ge SITRANS P410, Typ 7MF4*33-*++**-*E+*Z-C41 SITRANS P310, Typ 7MF2*33-*++**-*E+*
113 G Ex nA llC T 4/T5/T6 Ge
Hilfsenergie-/Ausgangssignalstromkreis
(Anschluss: +,-)
in Zündschutzart Nichtfunkend Ex nA llC
Um = 45 V
EG-Baumusterprüfbescheinigungen ohne Unterschrift und ohne Siegel haben keine Gültigkeit.
Diese EG-Baumusterprüfbescheinigung darf nur unverändert weiterverbreitet werden.
Auszüge oder Änderungen bedürfen der Genehmigung der Physikalisch-Technischen Bundesanstalt.
Physikalisch-Technische Bundesanstalt• Bundesallee 100 • 38116 Braunschweig • DEUTSCHLAND
Seite 3/5
P1B Physikalisch-Technische Bundesanstalt ' Braunschweig und Berlin
Nationales Metrologieinstitut
1. Ergänzung zur EG-Baumusterprüfbescheinigung PTB 13 ATEX 2007 X
Varianten Kennzeichnung
SITRANS P OS 111, Typ 7MF4*33-*++**-*E+* II 2/3 G Ex ic llC T 4/T5/T6 Ge SITRANS P410, Typ 7MF4*33-*++**-*E+*Z-C41 SITRANS P310, Typ 7MF2*33-*++**-*E+*
113 G Ex ic llC T 4/T5/T6 Ge
Hilfsenergie-/Ausgangssignalstromkreis (Anschluss: +,-)
in Zündschutzart Eigensicherheit Ex ic llC
Höchstwerte: Ui = 45 V
Li = 0,4 mH Ci = 6 nF
Varianten Kennzeichnung
SITRANS P OS 111 PA, Typ 7MF4*34-*++**-*E+* SITRANS P410-PA, SITRANS P310-PA,
SITRANS P OS III FF, SITRANS P410-FF, SITRANS P310-FF,
Hilfsenergie-/Ausgangssignalstromkreis (Anschluss: +,-)
Typ 7MF4*34-*++**-*E+*Z-C41 Typ 7MF2*34-*++**-*E+* II 2/3 G Ex nA llC T 4/T5/T6 Ge
Typ 7MF4*35-*++**-*E+* 113 G Ex nA llC T4/T5/T6 Ge
Typ 7MF4*35-*++**-*E+*Z-C41 Typ 7MF2*35-*++**-*E+*
in Zündschutzart Nichtfunkend Ex nA llC
Um = 32 V (max. Busspannung)
Varianten Kennzeichnung
SITRANS P OS 111 PA, Typ 7MF4*34-*++**-*E+* SITRANS P410-PA, SITRANS P310-PA,
SITRANS P OS III FF, SITRANS P410-FF, SITRANS P310-FF,
Hilfsenergie-/Ausgangssignalstromkreis (Anschluss: +,-)
Typ 7MF4*34-*++**-*E+*Z-C41 Typ 7MF2*34-*++**-*E+* II 2/3 G Ex ic llC T 4/T5/T6 Ge
Typ 7MF4*35-*++**-*E+* 113 G Ex ic llC T 4/T5/T6 Ge
Typ 7MF4*35-*++**-*E+*Z-C41 Typ 7MF2*35-*++**-*E+*
in Zündschutzart Eigensicherheit Ex ic llC zum Anschluss an ein FISCO-Speisegerät gemäß EN 60079-11 :2012 oder eine lineare Barriere mit den Werten entsprechend folgender Tabelle:
U1
h P1
FISCO-Speisegerät
7 µH 1, 1 nF
ic
17,5 V
570mA
lineare Barriere ic
32V
132 mA
1W
Seite 4/5
EG-Baumusterprüfbescheinigungen ohne Unterschrift und ohne Siegel haben keine Gültigkeit. Diese EG-Baumusterprüfbescheinigung darf nur unverändert weiterverbreitet werden.
Auszüge oder Änderungen bedürfen der Genehmigung der Physikalisch-Technischen Bundesanstalt.
Physikalisch-Technische Bundesanstalt• Bundesallee 100 • 38116 Braunschweig• DEUTSCHLAND
PTB Physlkallsch-Technlsche Bundesanstalt Braunschweig und Berlln Nationales Metrologieinstitut
1. Ergänzung zur EG-Baumusterprüfbescheinigung PTB 13 ATEX 2007 X
Besondere Bedingungen
1. Der Anschluss für den Potenzialausgleichsleiter der Messumformer SITRANS P OS III, SITRANS P410 und SITRANS P310 ist bei nichteigensicheren Varianten (Zündschutzart Ex nA llC) mit dem Potenzialausgleichssystem des explosionsgefährdeten Bereiches elektrisch zu verbinden. Die eigensicheren Varianten sind in geeigneter Weise elektrostatisch zu erden.
Alle weiteren „Besonderen Bedingungen" und Angaben der EG-Baumusterprüfbescheinigung gelten unverändert auch für diese 1. Ergänzung.
Angewandte Normen
EN 60079-0:2012 EN 60079-11 :2012 EN 60079-15:2010 EN 60079-26:2007
Prüfbericht: PTB Ex 15-25064
Braunschweig, 30. April 2015
Seite 5/5
EG-Baumusterprüfbescheinigungen ohne Unterschrift und ohne Siegel haben keine Gültigkeit. Diese EG-Baumusterprüfbescheinigung darf nur unverändert weiterverbreitet werden .
Auszüge oder Änderungen bedürfen der Genehmigung der Physikalisch-Technischen Bundesanstalt.
Physikalisch-Technische Bundesanstalt• Bundesallee 100 • 38116 Braunschweig• DEUTSCHLAND
E 0 -0 ai
0 0 ~
0
x UJ (/) N
Physikalisch-Technische Bundesanstalt Braunschweig und Berlin
(1) EC-TYPE-EXAMINATION CERTIFICATE (Translation)
(2) Equipment and Protective Systems lntended for Use in Potentially Explosive Atmospheres - Directive 94/9/EC
(3) EC-type-examination Certificate Number:
PTB 13 ATEX 2007 X (4) Equipment: Explosion protected pressure transducer
SITRANS PDS III Hart, SITRANS PDS III-PA, SITRANS PDS III-FF types 7MF4*** - * ++ * * - *B+ * and 7MF4*** - * ++ * * - *E+ *
(5) Manufacturer: Siemens AG lndustry Seetor
(6)
(7)
(8)
(9)
(10)
( 11)
(12)
lndustry Automation Division
Address: 76181 Karlsruhe, Germany This equipment and any acceptable variation thereto are specified in the schedule to this certificate and the documents therein referred to. The Physikalisch-Technische Bundesanstalt, notified body No. 0102 in accordance with Article 9 of the Council Directive 94/9/EC of 23 March 1994, certifies that this equipment has been found to comply with the Essential Health and Safety Requirements relating to the design and construction of equipment and protective systems intended for use in potentially explosive atmospheres, given in Annex II to the Directive.
The examination and test results are recorded in the confidential test report PTB Ex 13-22337. Compliance with the Essential Health and Safety Requirements has been assured by compliance with: EN 60079-0:2009 EN 60079-11:2012 EN 60079-15:2010 EN 60079-26:2007 lf the sign "X" is placed after the certificate number, it indicates that the equipment is subject to special conditions for safe use specified in the schedule to this certificate. This EC-type-examination Certificate relates only to the design, examination and tests of the specified equipment in accordance to the Directive 94/9/EC. Further requirements of the Directive apply to the manufacturing process and supply of this equipment. These are not covered by this certificate. The marking of the equipment shall include the following:
@ 111/2 G Ex ia llC T4/T5/T6 Ga 111/2 G Ex ib llC T4/T5/T6 Gb II 2/3 G Ex nA llC T4/T5/T6 Ge II 2/3 G Ex ie llC T4/T5/T6 Ge II 3 G Ex nA llC T4/T5/T6 Ge II 3 G Ex ie llC T4/T5/T6 Ge
Braunschweig, September 23, 2013
sheet 1/7
EC-type-examination Certificates w1thout signature and official stamp shall not be valid. The certificates may be circulated only without alteration. Extraeis or alterations are subject to approval by the Physikalisch-Technische Bundesanstalt.
In case of dispute, the German !ext shall prevail.
Physikalisch-Technische Bundesanstalt • Bundesallee 100 • 38116 Braunschweig • GERMANY
Physikalisch-Technische Bundesanstalt Braunschweig und Berlin
(13) S C H E D U L E
(14) EC-TYPE-EXAMINATION CERTIFICATE PTB 13 ATEX 2007 X
(15) Oescription of equipment
The explosion protected pressure transducer SITRANS P OS III Hart, SITRANS P OS III-PA, SITRANS POS III-FF, Typen 7MF4*** - * ++ * * - *B+ * and 7MF4*** - * ++ * * - *E+ * is used for the measurement of non-corrosive and corrosive gases, vapours and liquids. The equipment consists of the components enclosure, electronic assembly and measuring cell. The pressure to be measured is transmitted to the hermetically sealed sensor unit by means of a separating diaphragm and an oil-filled system. This arrangement guarantees the separation of areas from each other where equipment of categories 1/2 or 2/3 is required.
The measuring signal is conditioned in the electronic assembly making it available as a loadindependent direct current, 4-20 mA (HART) or as a bus signal (FF or Profibus-PA).
Category-1 /2-egui pment
The enclosure for the electronic system is installed in hazardous areas requiring equipment of category 2. The process connection elements are mounted into the partition separating areas from each other where equipment of category 1 or 2 is required.
For relationship between temperature class, maximum permissible medium temperature and maximum permissible ambient temperature at the electronic system, reference is made to the following table:
Temperature class Medium temperature Ambient temperature at the electronic system
T4 -20 „. + 60 °C -40 „. +85 °C T5 -20 „. + 60 °C -40 „. +70 °C T6 -20 „. + 60 °C -40 „. +60 °C
For applications requiring category-1-equipment the process pressure shall range from 0.8 bar to 1.1 bar.
The operating conditions for operation without explosive mixtures shall be taken from the manufacturer' s specifications.
sheet 2/7
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only without alteration. Extracts or alterations are subject to approval by the Physikalisch-Technische Bundesanstalt.
In case of dispute, the German text shall prevail.
Physikalisch-Technische Bundesanstalt • Bundesallee 100 • 38116 Braunschweig • GERMANY
Physikalisch-Technische Bundesanstalt Braunschweig und Berlin
SCHEDULE TO EC-TYPE-EXAMINATION CERTIFICATE PTB 13 ATEX 2007 X
Category-2-equipment
The measuring transducers are installed in hazardous areas requiring equipment of category 2.
For relationship between maximum permissible ambient temperature and temperature class reference is made to the following table:
Temperature class Ambient temperature T4 -40 ... +85 °C T5 -40 ... +70 °C T6 -40 ... +60 °C
The permissible operating temperatures and pressures for the operation shall be taken from the manufacturer's specifications.
Category-2/3-eq u i pment
The enclosure for the electronic system is installed in hazardous areas requiring equipment of category 3. The process connection elements are mounted into the partition separating areas from each other where equipment of category 2 or 3 is required.
For relationship between maximum permissible ambient temperature and temperature class reference is made to the following table:
Temperature class Ambient temperature T4 -40 ... +85 °C T5 -40 ... +70 °C T6 -40 ... +60 °C
The operating conditions for operation without explosive mixtures shall be taken from the manufacturer' s specifications.
Category-3-eq u i pment
The measuring transducers are installed in hazardous areas requiring equipment of category 3.
For relationship between maximum permissible ambient temperature and temperature class reference is made to the following table:
Temperature class Ambient temperature T4 -40 ... +85 °C T5 -40 ... +70 °C T6 -40 ... +60 °C
The operating conditions for operation without explosive mixtures shall be taken from the manufacturer's specifications.
sheet 3/7
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only without alteration. Extracts or alterations are subject to approval by the Physikalisch-Technische Bundesanstalt.
In case of dispute, the German text shall prevail.
Physikalisch-Technische Bundesanstalt • Bundesallee 100 • 38116 Braunschweig • GERMANY
Physikalisch-Technische Bundesanstalt Braunschweig und Berlin
SCHEDULE TO EC-TYPE-EXAMINATION CERTIFICATE PTB 13 ATEX 2007 X
Electrical data
Variant Marking
SITRANS P DS III, Typ 7MF4*33-*++**-*B+* 111/2 G Ex ia llC T4/T5/T6 Ga II 1/2 G Ex ib llC T4/T5/T6 Gb
Auxiliary power-/output signal circuit (terminals: +,-)
Variants
type of protection lntrinsic Safety Ex ia llC or Ex ib llC
only for connection to a certified intrinsically safe circuit
Maximum values:
Ui = 30 V li = 100 mA Pi = 750 mW
Li = 0.4 mH Ci = 6 nF
Marking (applicable to both variants)
SITRANS PDS III PA, Typ 7MF4*34-*++**-*B+* II 1/2 G Ex ia llC T4/T5/T6 Ga SITRANS PDS III FF, Typ 7MF4*35-*++**-*B+* II 1/2 G Ex ib llC T4/T5/T6 Gb
Auxiliary power-/output signal circuit (terminals: +,-)
type of protection lntrinsic Safety Ex ia llC or Ex ib llC
only for connection to a certified intrinsically safe circuit (e.g. FISCO-supply unit or a linear barrier) with the maximum values specified in the following table:
FISCO-supply unit linear barrier ia / ib ia I ib
ui 17.5 V 24 V
li 380 mA 174 mA
pi 5.32W 1W
Li = 7 µH Ci = 1.1 nF
sheet 4/7
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only without alteration. Extraeis or alterations are subject to approval by the Physikalisch-Technische Bundesanstalt.
In case of dispute, the German text shall prevail.
Physikalisch-Technische Bundesanstalt• Bundesallee 100 • 38116 Braunschweig • GERMANY
Physikalisch-Technische Bundesanstalt Braunschweig und Berlin
SCHEDULE TO EC-TYPE-EXAMINATION CERTIFICATE PTB 13 ATEX 2007 X
Variants Marking (applieable to all three variants)
SITRANS P DS III, Typ 7MF4*33-*++**-*B+* 111/2 G Ex ia llC T4/T5/T6 Ga
SITRANS PDS III PA, Typ 7MF4*34-*++**-*B+* 111/2 G Ex ib llC T4/T5/T6 Gb SITRANS PDS III FF, Typ 7MF4*35-*++**-*B+*
Pilot indicator signal circuit (terminals: plug-in contacts, flat connector)
Measuring cell circuit
Variant
type of protection lntrinsic Safety Ex ia llC or Ex ib llC
only for connection to floating indicators ortest instruments without internal power supply (battery, mains) and without external circuits
or
for connection to test instruments which are approved for operation in explosion hazardous areas
Maximum values for the interconnection of pilot indicator signal circuit and test instrument
Ui = 30 V li = 100 mA Pi = 750 mW
llC L0 [mH] 0.5 Co rnFl 3
internal circuit, no external interface
Marking
SITRANS P DS 111, Typ 7MF4*33-*++**-*E+* 11 2/3 G Ex nA llC T4/T5/T6 Ge 113 G Ex nA llC T4/T5/T6 Ge
Auxiliary power-/output signal circuit (terminals: +,-)
Variant
type of protection Non-sparking Ex nA 11
Um = 45 V
Marking
SITRANS PDS III, Typ 7MF4*33-*++**-*E+* II 2/3 G Ex ie llC T4/T5/T6 Ge 113 G Ex ie llC T4/T5/T6 Ge
Auxiliary power-/output signal circuit (terminals: +,-)
type of protection lntrinsic Safety Ex ic llC
Maximum values: Ui = 45 V
Li = 0.4 mH Ci = 6 nF
sheet 5/7
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only without alteration. Extracts or alterations are subject to approval by the Physikalisch-Technische Bundesanstalt.
In case of dispute, the German text shall prevail.
Physikalisch-Technische Bundesanstalt • Bundesallee 100 • 38116 Braunschweig • GERMANY
Physikalisch-Technische Bundesanstalt Braunschweig und Berlin
SCHEDULE TO EC-TYPE-EXAMINATION CERTIFICATE PTB 13 ATEX 2007 X
Variants Marking (applicable to both variants)
SITRANS P OS 111 PA, Typ 7MF4*34-*++**-*E+* II 2/3 G Ex nA llC T4/T5/T6 Ge SITRANS POS III FF, Typ 7MF4*35-*++**-*E+* II 3 G Ex nA llC T4/T5/T6 Ge
Auxiliary power-/output signal circuit (terminals: +,-)
Variant
type of protection Non-sparking Ex nA 11
Um = 32 V (max. bus voltage)
Marking (applieable to both variants)
SITRANS POS III PA, Typ 7MF4*34-*++**-*B+* II 2/3 G Ex ie llC T4/T5/T6 Ge SITRANS POS III FF, Typ 7MF4*35-*++**-*B+* II 3 G Ex ie llC T4/T5/T6 Ge
Auxiliary power-/output signal circuit (terminals: +,-)
( 16) Test report PTB Ex13-22337
(17) Special conditions for safe use
type of protection lntrinsic Safety Ex ic llC for connection to an FISCO-supply unit according to EN 60079-11 :2012 or to a linear barrier with the maximum values specified in the following table:
FISCO-supply unit linear barrier ie ie
ui 17.5 V 32 V
li 570mA 132 mA
pi 1W
Li = 7 µH Ci = 1.1 nF
1. For non-intrinsically safe variants (type of protection Ex nA) the terminal for the equipotential bonding conductor of the pressure transducer SITRANS P OS III shall be electrically connected to the equipotential bonding system of the hazardous area. The intrinsically safe variants shall be earthed electrostatically using an appropriate method.
2. Plug facilities or plug connectors for the connection of external circuits are not permitted for the application as category-3-equipment with type of protection "Non-sparking" (nA).
3. The explosion protection of the pressure transducer particularly depends on the tightness of the diaphragm when the equipment is connected to intrinsically safe circuits of category "ib" and simultaneously mounted and operated in the partition between areas where equipment of category 1 or category 2 is required. For these operating conditions the pressure transducer shall only be used for such flammable media, the diaphragm is sufficiently resistent to, with respect to chemical influences and corrosion.
sheet 6/7
EC-type-exarnination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only without alteration. Extracts or alterations are subject to approval by the Physikalisch-Technische Bundesanstalt.
In case of dispute, the German text shall prevail.
Physikalisch-Technische Bundesanstalt • Bundesallee 100 • 38116 Braunschweig • GERMANY
Physikalisch-Technische Bundesanstalt Braunschweig und Berlin
SCHEDULE TO EC-TYPE-EXAMINATION CERTIFICATE PTB 13 ATEX 2007 X
(18) Essential health and safety requirements
met by compliance with the standards mentioned above
Zertifizierungssektor Explosionsschutz Braunschweig, September 23, 2013 ~ha~f Qf PTB:
Ua \
"" Dr.-lng. T. Horn
sheet 7/7
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only without alteration. Extracts or alterations are subject to approval by the Physikalisch-Technische Bundesanstalt.
In case of dispute, the German text shall prevail.
Physikalisch-Technische Bundesanstalt • Bundesallee 100 • 38116 Braunschweig • GERMANY
.J:J
Q) .... 0 .... 0
~ g]
P1B Physikallsch-Technische Bundesanstalt ' Braunschweig und Berlln
Nationales Metrologieinstitut
1. SUPPLEMENT
according to Directive 94/9/EC Annex 111.6
to EC-TYPE-EXAMINATION CERTIFICATE PTB 13 ATEX 2007 X
Equipment:
(Translation)
Explosion protected pressure transducer SITRANS PDS III Hart, SITRANS PDS III-PA, SITRANS P DS 111-FF types 7MF4*** - * ++ * * - *B+ * and 7MF4*** - * ++ * * - *E+ *
Marking: @ 111/2 G II 2/3 G 113 G
Ex ia llC T 4/T5/T6 Ga Ex nA llC T4/T5/T6 Ge Ex nA llC T 4/T5/T6 Ge
111/2 G II 2/3 G 113 G
Ex ib llC T 4/T5/T6 Gb Ex ie llC T 4/T5/T6 Ge Ex ic llC T4/T5/T6 Ge
Manufacturer: Siemens AG - Process lndustries and Drives formerly Siemens AG lndustry Seetor lndustry Automation Division
Address: 76181 Karlsruhe, Germany
Description of supplements and modifications
In the future the explosion protected pressure transducer SITRANS PDS III Hart, SITRANS PDS
111-PA, SITRANS P DS 111-FF, types 7MF4*** - * ++ * * - *B+ * and 7MF4*** - * ++ * * - *E+ *
may also be manufacturd and operated according to the test documents listed in the test report.
The modifications concern the introduction of the new variants SITRANS P41 O Hart, SITRANS
P410-PA, SITRANS P410-FF, types 7MF4*** - * ++ * * - *B+ * Z-C41 and 7MF4*** - * ++ * * -
*E+ * Z-C41 as well as SITRANS P310 Hart, SITRANS P310-PA, SITRANS P310-FF, types
7MF2*** - * ++ * * - *B+ * and 7MF2*** - * ++ * * - *E+ * . These new variants differ from the
previous types in their calibration accuracy (software), the technical design applies without
changes .
The electrical data and "Special Condition" No. 1 are extended for the new variants.
Furthermore, the applied standards are adapted to the current state and the name of the
manufacturer changes as given above.
Sheet 1/5
EC-type-examination Certificates without signature and official stamp shall not be valid . The certificates may be circulated
only without alteration. Extracts or alterations are subject to approval by the Physikalisch-Technische Bundesanstalt.
In case .of dispute, the German text shall prevail.
Physikalisch-Technische Bundesanstalt• Bundesallee 100 • 38116 Braunschweig• GERMANY
PTB Physlkallsch-Technlsche Bundesanstalt ' Braunschweig und Berlln
Nationales Metrologieinstitut
1. SUPPLEMENT TO EC-TYPE-EXAMINATION CERTIFICATE PTB 13 ATEX 2007 X
Electrical data
Variant Marking
SITRANS P OS III, Typ 7MF4*33-*++**-*B+* 111/2 G Ex ia llC T4/T5/T6 Ga SITRANS P410, Typ 7MF4*33-*++**-*B+*Z-C41 111/2 G Ex ib llC T4/T5/T6 Gb SITRANS P310, Typ 7MF2*33-*++**-*B+*
Auxiliary power-/output signal circuit (terminals: +,-)
Variants
type of protection lntrinsic Safety Ex ia llC or Ex ib llC
only for connection to a certified intrinsically safe circuit
Maximum values:
Ui = 30 V li = 100 mA Pi = 750 mW
Li = 0.4 mH Ci = 6 nF
Marking
SITRANS POS III PA, Typ 7MF4*34-*++**-*B+* SITRANS P410-PA, SITRANS P310-PA,
SITRANS P OS III FF, SITRANS P410-FF, SITRANS P310-FF,
Auxiliary power-/output signal circuit (terminals: +,-)
Typ 7MF4*34-*++**-*B+*Z-C41 Typ 7MF2*34-*++**-*B+* 111/2 G Ex ia llC T 4/T5/T6 Ga
Typ 7MF4*35-*++**-*B+* 111/2 G Ex ib llC T4/T5/T6 Gb
Typ 7MF4*35-*++**-*B+*Z-C41 Typ 7MF2*35-*++**-*B+*
type of protection lntrinsic Safety Ex ia llC or Ex ib llC
only for connection to a certified intrinsically safe circuit (e.g. FISCO-supply unit or a linear barrier) with the maximum values specified in the following table:
U1
11
P1
FISCO-supply unit
7 µH 1.1 nF
ia I ib
17.5 V
380mA
5.32W
linear barrier ia I ib
24 V
174 mA
1W
Sheet 2/5
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated
only without alteration. Extracts or alterations are subject to approval by the Physikalisch-Technische Bundesanstalt. In case of dispute, the German text shall prevail.
Physikalisch-Technische Bundesanstalt• Bundesallee 100 • 38116 Braunschweig • GERMANY
PlB Physlkallsch-Technlsche Bundesanstalt Braunschweig und Berlin Nationales Metrologieinstitut
1. SUPPLEMENT TO EC-TYPE-EXAMINATION CERTIFICATE PTB 13 ATEX 2007 X
Variants Marking
SITRANS P OS III, Typ 7MF4*33-*++**-*B+* SITRANS P410, Typ 7MF4*33-*++**-*B+*Z-C41 SITRANS P310, Typ 7MF2*33-*++**-*B+*
SITRANS POS III PA, Typ 7MF4*34-*++**-*B+* 111/2 G Ex ia llC T 4/T5/T6 Ga SITRANS P410-PA, Typ 7MF4*34-*++**-*B+*Z-C41 SITRANS P310-PA, Typ 7MF2*34-*++**-*B+*
111/2 G Ex ib llC T4/T5/T6 Gb
SITRANS POS III FF, Typ 7MF4*35-*++**-*B+* SITRANS P410-FF, Typ 7MF4*35-*++**-*B+*Z-C41 SITRANS P310-FF, Typ 7MF2*35-*++**-*B+*
Pilot indicator signal circuit (terminals: plug-in contacts, flat connector)
type of protection lntrinsic Safety Ex ia llC or Ex ib llC
only for connection to floating indicators or test instruments without intemal power supply (battery, mains)
and without extemal circuits
Measuring cell circuit
Variant
or
for connection to test instruments which are approved for operation in explosion hazardous areas
Maximum values for the interconnection of pilot indicator signal circuit and test instrument
Ui = 30 V li = 100 mA Pi = 750 mW
llC 0.5 3
intemal circuit, no extemal interface
Marking
SITRANS P OS III, Typ 7MF4*33-*++**-*E+* 11 2/3 G Ex nA llC T 4/T5/T6 Ge SITRANS P410, Typ 7MF4*33-*++**-*E+*Z-C41 113 G Ex nA llC T 4/T5/T6 Ge SITRANS P310, Typ 7MF2*33-*++**-*E+*
Auxiliary power-/output signal circuit (terminals: +,-)
type of protection Non-sparking Ex nA llC
Um = 45 V
Sheet 3/5
EC-type-examination Certificates without signature and official stamp shall not be valid. The certi~cates may be circulated
only without alteration. Extracts or alterations are subject to approval by the Physikalisch-Technische Bundesanstalt.
In case of dlspute. the German taxt shall prevail.
Physikalisch-Technische Bundesanstalt• Bundesallee 100 • 38116 Braunschweig• GERMANY
PJB Physlkallsch-Technische Bundesanstalt ' Braunschweig und Berlin
Nationales Metrologieinstitut
1. SUPPLEMENT TO EC-TYPE-EXAMINATION CERTIFICATE PTB 13 ATEX 2007 X
Variant Marking
SITRANS P OS 111, Typ 7MF4*33-*++**-*E+* 11 2/3 G Ex ie llC T4/T5/T6 Ge SITRANS P410, Typ 7MF4*33-*++**-*E+*Z-C41 113 G Ex ie llC T 4/T5/T6 Ge SITRANS P310, Typ 7MF2*33-*++**-*E+*
Auxiliary power-/output signal circuit (terminals: +,-)
Variants
type of protection lntrinsic Safety Ex ic llC
Maximum values: Ui = 45 V
Li = 0.4 mH Ci = 6 nF
Marking
SITRANS P OS III PA, Typ 7MF4*34-*++**-*E+* SITRANS P410-PA, SITRANS P310-PA,
SITRANS P OS III FF, SITRANS P410-FF, SITRANS P310-FF,
Auxiliary power-/output signal circuit (terminals: +,-)
Typ 7MF4*34-*++**-*E+*Z-C41 Typ 7MF2*34-*++**-*E+* II 2/3 G Ex nA llC T 4/T5/T6 Ge
Typ 7MF4*35-*++**-*E+* 113 G Ex nA llC T 4/T5/T6 Ge
Typ 7MF4*35-*++**-*E+*Z-C41 Typ 7MF2*35-*++**-*E+*
type of protection Non-sparking Ex nA llC
Um = 32 V (max. bus voltage)
Variant Marking
SITRANS POS III PA, Typ 7MF4*34-*++**-*E+* SITRANS P410-PA, SITRANS P310-PA,
SITRANS POS III FF, SITRANS P410-FF, SITRANS P310-FF,
Auxiliary power-/output signal circuit (terminals: +,-)
Typ 7MF4*34-*++**-*E+*Z-C41 Typ 7MF2*34-*++**-*E+* 11 2/3 G Ex ie llC T4/T5/T6 Ge
Typ 7MF4*35-*++**-*E+* 113 G Ex ie llC T 4/T5/T6 Ge
Typ 7MF4*35-*++**-*E+*Z-C41 Typ 7MF2*35-*++**-*E+*
type of protection lntrinsic Safety Ex ic llC for connection to an FISCO-supply unit according to EN 60079-11 :2012 or to a linear barrier with the maximum values specified in the following table:
ui 11
P1
FISCO-supply unit
7 µH 1.1 nF
ie
17.5 V
570mA
linear barrier ie
32V
132 mA
1W
Sheet 4/5
EC-type-examination Certiflcates without signature and official stamp shall not be valid . The certificates may be circulated
only without alteration. Extracts or alterations are subject to approval by the Physikalisch-Technische Bundesanstalt.
In case of dispute. the German text shall prevail.
Physikalisch-Technische Bundesanstalt• Bundesallee 100 • 38116 Braunschweig • GERMANY
PIB Physikallsch-Technische Bundesanstalt 1 Braunschweig und Berlin
Nationales Metrologieinstitut
1. SUPPLEMENT TO EC-TYPE-EXAMINATION CERTIFICATE PTB 13 ATEX 2007 X
Special conditions for safe use
1. For non-intrinsically safe variants (type of protection Ex nA llC) the terminal for the
equipotential bonding conductor of the pressure transducer SITRANS P DS III, SITRANS
P410 and SITRANS P310 shall be electrically connected to the equipotential bonding system
of the hazardous area. The intrinsically safe variants shall be earthed electrostatically using an appropriate method.
All further "Special Conditions" and specifications of the EC-type examination certificate apply
without changes also to this 1 st supplement.
Applied standards
EN 60079-0:2012 EN 60079-11 :2012 EN 60079-15:2010 EN 60079-26:2007
Test report: PTB Ex 15-25064
Braunschweig, April 30, 2015
Sheet 5/5
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated
only without alteration. Extracts or alteratlons are subject to approval by the Physikalisch-Technische Bundesanstalt.
In case of dispute, the German text shall prevail.
Physikalisch-Technische Bundesanstalt• Bundesallee 100 • 38116 Braunschweig• GERMANY